Kia_Sedona_2002-2006

Power Door Locks

Print

Door Lock Control Panel



Removal & Installation

WARNING
Be careful not the scratch the door trim and other parts. Wear gloves to protect your hands.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the quadrant inner cover.

    Click image to see an enlarged view

    Fig. Remove the quadrant inner cover (A)

  4.  
  5. Loosen the mounting screw, remove the inside handle cover.

    Click image to see an enlarged view

    Fig. Loosen the mounting screw, then remove the inside handle cover (A)

  6.  
  7. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D).

    Click image to see an enlarged view

    Fig. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D)

  8.  
  9. Loosen the mounting screws, then detach the connector (A).

    Click image to see an enlarged view

    Fig. Loosen the mounting screws, then detach the connector (A)



    Click image to see an enlarged view

    Fig. Remove the switch assembly (A)

  10.  
  11. Installation is the reverse of the removal procedure.
  12.  

Door Lock Motor



Removal & Installation

WARNING
Be careful not the scratch the door trim and other parts. Wear gloves to protect your hands.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the quadrant inner cover.

    Click image to see an enlarged view

    Fig. Remove the quadrant inner cover (A)

  4.  
  5. Loosen the mounting screw, remove the inside handle cover.

    Click image to see an enlarged view

    Fig. Loosen the mounting screw, then remove the inside handle cover (A)

  6.  
  7. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D).

    Click image to see an enlarged view

    Fig. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D)

  8.  
  9. Remove the door glass as follows:
    1. Remove the door trim seal.

      Click image to see an enlarged view

      Fig. Remove the door trim seal (A)

    2.  
    3. Carefully move the glass (A) until you can see the bolts, then loosen them. Carefully pull the glass out through the window slot (B).

      Click image to see an enlarged view

      Fig. Carefully move the glass (A) until you can see the bolts, then loosen them. Carefully pull the glass out through the window slot (B)

    4.  

  10.  
  11. Detach the wiring harness.

    Click image to see an enlarged view

    Fig. Detach the wiring harness (A)

  12.  
  13. Detach the lock rod (A) and outside handle rod (B).

    Click image to see an enlarged view

    Fig. Detach the lock rod (A) and outside handle rod (B).

  14.  
  15. Loosen the door module mounting bolts, then remove the door module (A).

    Click image to see an enlarged view

    Fig. Loosen the door module mounting bolts, then remove the door module (A)

  16.  
  17. Installation is the reverse of the removal procedure. Note the following:
    1. Roll the glass up and down to make sure it moves freely and without binding.
    2.  
    3. Make sure there is no clearance between the glass and glass run channel when the glass is closed.
    4.  
    5. Adjust the position of the glass if necessary.
    6.  

  18.  

 
label.common.footer.alt.autozoneLogo