Kia_Sephia_Rio_Spectra_Optima_1998-2006

TroubleCodes (29 of 130)

Print

1.8L L4 VIN 1 Auto



Trouble Code: P0507

Idle Speed Higher Than Expected

Trouble Code Conditions: Engine running at idle speed while in closed loop, and the PCM detected the Actual idle speed was more than 200 rpm above the Target idle speed during the CCM test.

Possible Causes:



High resistance between the main relay and IAC valve
 
High resistance between PCM and IAC valve control circuits
 
IAC valve is damaged or has failed
 
Intake air leak located below the throttle plate assembly
 

Trouble Code: P0560

Battery Backup Line Circuit Malfunction

Trouble Code Conditions: Engine runtime over 4 minutes and the PCM did not detect any system voltage on the Battery Backup circuit for 5 seconds.

Possible Causes:



Battery backup circuit to the PCM is open
 
Battery backup fuse to the PCM is open or missing
 
Battery backup circuit to the PCM has high resistance
 
PCM has failed
 

Trouble Code: P0561

System Voltage Unstable

Trouble Code Conditions: Engine runtime over 4 minutes, and the PCM detected the system voltage rapidly changed its value by more than 3 volts. Note: If the Battery Backup circuit is open, the vehicle will not run.

Possible Causes:



Charging system problem (charging voltage interrupted)
 
Backup voltage circuit to the PCM open (intermittent fault)
 
PCM has failed
 

Trouble Code: P0562

System Voltage Low Input

Trouble Code Conditions: Engine runtime over 4 minutes, and the PCM detected the system voltage was less than 8.0 volts, condition met for 5 seconds. Note: If the Battery Backup circuit is open, the vehicle will not run.

Possible Causes:



Charging system problem (charging voltage too low)
 
Battery backup circuit to the PCM has high resistance
 
Backup voltage circuit to the PCM open (intermittent fault)
 
PCM has failed
 

Trouble Code: P0563

System Voltage High Input

Trouble Code Conditions: Engine runtime over 4 minutes, and the PCM detected the system voltage was more than 17.0 volts, condition met for 5 seconds. Note: If the Battery Backup circuit is open, the vehicle will not run.

Possible Causes:



Charging system problem (charging voltage too high)
 
Backup voltage circuit to the PCM open (intermittent fault)
 
PCM has failed
 

Trouble Code: P0601

PCM or TCM Internal Random Check Sum Error

Trouble Code Conditions: Key on or engine running and the PCM or the TCM detected that a Random Check Sum Error was present.

Possible Causes:



Poor terminal contact at the ECM ISC Backup Voltage circuit
 
PCM or TCM has an internal problem or has failed
 

Trouble Code: P0604

PCM or TCM Internal Random Access Memory Error

Trouble Code Conditions: Key on or engine running and the PCM or TCM detected an Internal Random Access Memory (RAM) error was present.

Possible Causes:



Poor terminal contact at the ECM Backup Voltage circuit
 
PCM or TCM has an internal problem or has failed
 

Trouble Code: P0650

Malfunction Indicator Lamp Circuit Malfunction

Trouble Code Conditions: Key on or engine running and the PCM detected an unexpected voltage condition on the Malfunction Indicator Lamp (MIL) circuit.

Possible Causes:



MIL control circuit open
 
MIL control circuit shorted to ground
 
MIL "bulb" is damaged or missing
 
PCM has failed (MIL control "driver" may be open or shorted)
 

Trouble Code: P0705

Transmission Range Switch Circuit Malfunction

Trouble Code Conditions: Engine running with VSS inputs received, and the PCM detected invalid signals or multiple TR switch inputs with the gearshift in drive. Note: If DTC P1500 is also set, check the Meter Fuse and circuit.

Possible Causes:



TR switch signal circuit is open or shorted to ground
 
TR switch signal circuit is shorted to VREF or system power
 
TR switch is damaged or has failed
 
PCM has failed
 
TSB 2TD007 (12/01) contains information related to this code
 

Trouble Code: P0712

Transmission Fluid Temperature Low Input

Trouble Code Conditions: Key on or engine running and the PCM detected the TFT sensor signal indicated less than 0.49 volt 300°F) for more than 1 second. Note: The TFT sensor signal at 68°F is 4.0 volts, and at 266°F it is 1.5 volts.

Possible Causes:



TFT sensor signal circuit shorted to ground (sensor to TCM)
 
TFT sensor signal circuit shorted to ground (TCM to PCM)
 
TFT sensor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0713

Transmission Fluid Temperature High Input

Trouble Code Conditions: Key on or engine running and the PCM detected the TFT sensor signal indicated more than 4.57 volts (-40°F) during the CCM test period. Note: The TFT sensor signal at 68°F is 4.0 volts, and at 266°F it is 1.5 volts.

Possible Causes:



TFT sensor signal circuit is open (sensor circuit to the TCM)
 
TFT sensor signal circuit is open (TCM circuit to the PCM)
 
TFT sensor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0715

Input/Turbine Speed Sensor Circuit Malfunction

Trouble Code Conditions: Vehicle driven to a speed of over 15.5 mph with the engine speed over 1500 rpm in 3rd or 4th gear, and the PCM did not detect any Input/Turbine speed sensor signals for 5 seconds.

Possible Causes:



Input/Turbine speed sensor signal circuit open or shorted
 
Input/Turbine speed sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0716

Input/Turbine Speed Sensor Performance

Trouble Code Conditions: Vehicle drive to a speed of over 25 mph, gear ratio indicating the vehicle is in Drive, 2nd or 1st gear, and the PCM did not detect any Input/Turbine Speed sensor signals, or that the Input/Turbine sensor signals indicated less than 98 rpm during the CCM test.

Possible Causes:



Input/Turbine speed sensor signal circuit open or shorted
 
Input/Turbine speed sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0717

Input/Turbine Speed Sensor No Signal

Trouble Code Conditions: Vehicle drive to a speed of over 25 mph, gear ratio indicating the vehicle is in Drive, 2nd or 1st gear, and the PCM detected that the Input/Turbine Speed sensor signal indicated less than 98 rpm.

Possible Causes:



Input/Turbine speed sensor signal circuit open or shorted
 
Input/Turbine speed sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0726

Engine Speed Signal High Input

Trouble Code Conditions: Engine running, throttle position angle from 5-94%, and the TCM detected the Engine Speed signal indicated more than 7500 rpm.

Possible Causes:



Engine Speed Signal circuit open (PCM to the TCM)
 
Engine Speed Signal circuit shorted to ground (PCM to TCM)
 
PCM has failed
 
TCM has failed
 

Trouble Code: P0727

Engine Speed Signal Low Input

Trouble Code Conditions: Engine running, throttle position angle from 5-94%, gear selector not indicating 'P' or 'N' position, and the TCM detected the Engine Speed signal indicated less than 96 rpm during the CCM test.

Possible Causes:



Engine Speed Signal circuit open (PCM to the TCM)
 
Engine Speed Signal circuit shorted to ground (PCM to TCM)
 
PCM has failed
 
TCM has failed
 

Trouble Code: P0731

TCM Incorrect First Gear Ratio

Trouble Code Conditions: Vehicle driven at 12-32 mph in 3rd gear, shift solenoids 'A', 'B' and 'C', input/turbine speed sensor and TFT sensor inputs all indicating okay, and the PCM detected the 1st gear ratio was too high.

Possible Causes:



ATF fluid level too low or line pressure low
 
Control valve stuck or solenoid valve is damaged or has failed
 
Forward clutch, 3-4 brake band or 1-way clutch No. 1 slippage
 
PCM has failed
 
TSB 2TD007 (12/01) contains information related to this code
 

Trouble Code: P0732

TCM Incorrect Second Gear Ratio

Trouble Code Conditions: Vehicle driven at 17-60 mph in 2nd gear, shift solenoids 'A', 'B' and 'C', input/turbine speed sensor and TFT sensor inputs all indicating okay, and the PCM detected the 2nd gear ratio was too high.

Possible Causes:



ATF fluid level too low or line pressure low
 
Control valve stuck or solenoid valve is damaged or has failed
 
Forward clutch, 2-4 brake band or 1-way clutch No. 1 slippage
 
PCM has failed
 
TSB 2TD004 (8/00) contains information related to this code
 
TSB 2TD007 (12/01) contains information related to this code
 
TSB 3TD008 (3/02) contains information related to this code
 

Trouble Code: P0733

TCM Third Gear Incorrect Ratio

Trouble Code Conditions: Vehicle driven at 19-32 mph in 3rd gear, shift solenoids 'A', 'B' and 'C', input/turbine speed sensor and TFT sensor inputs all indicating okay, and the PCM detected the 3rd gear ratio was too high.

Possible Causes:



ATF fluid level too low or line pressure low
 
Control valve stuck or solenoid valve is damaged or has failed
 
Forward clutch, 3-4 brake band or 1-way clutch No. 1 slippage
 
PCM has failed
 
TSB 2TD004 (8/00) contains information related to this code
 
TSB 2TD007 (12/01) contains information related to this code
 
TSB 3TD008 (3/02) contains information related to this code
 

Trouble Code: P0734

TCM Fourth Gear Incorrect Ratio

Trouble Code Conditions: Vehicle driven at 44-65 mph in 4th gear, shift solenoids 'A', 'B' and 'C', input/turbine speed sensor and TFT sensor inputs all indicating okay, and the PCM detected the 4th gear ratio was too high.

Possible Causes:



ATF fluid level too low or line pressure low
 
Control valve stuck or solenoid valve is damaged or has failed
 
2-4 brake band or 3-4 clutch slippage
 
PCM has failed
 
TSB 2TD004 (8/00) contains information related to this code
 
TSB 2TD007 (12/01) contains information related to this code
 
TSB 3TD008 (3/02) contains information related to this code
 

Trouble Code: P0740

TCC System Malfunction

Trouble Code Conditions: Vehicle driven at 44-65 mph in 4th gear in TCC, shift solenoids 'A', 'B' and 'C', input/turbine speed sensor and TFT sensor inputs all okay, and the PCM detected the difference in the number of engine revolutions and reverse/forward drum revolutions was over 100 rpm.

Possible Causes:



ATF fluid level too low or line pressure low
 
Torque converter clutch slippage excessive
 
Control valve stuck or TCC solenoid is damaged or has failed
 
PCM has failed
 
TSB 2TD004 (8/00) contains information related to this code
 
TSB 2TD005 (11/00) contains information related to this code
 
TSB 2TD007 (12/01) contains information related to this code
 
TSB 3TD008 (3/02) contains information related to this code
 

Trouble Code: P0743

TCC Solenoid Circuit Malfunction

Trouble Code Conditions: Engine running in gear with VSS inputs received, and the PCM detected an unexpected voltage condition on the TCC circuit.

Possible Causes:



TCC solenoid control circuit is open or shorted to ground
 
TCC solenoid control circuit is shorted to system power (B+)
 
TCC solenoid is damaged or has failed
 
PCM or TCM has failed
 

Trouble Code: P0748

TCM Linear Solenoid Circuit Malfunction

Trouble Code Conditions: Engine running in gear with VSS inputs received, and the PCM detected an unexpected voltage on the Linear solenoid circuit.

Possible Causes:



Linear solenoid control circuit open or shorted to ground
 
Linear solenoid control circuit shorted to system power (B+)
 
Linear solenoid is damaged or has failed
 
PCM or TCM has failed
 

Trouble Code: P0753

TCM Shift Solenoid 'A' Circuit Malfunction

Trouble Code Conditions: Engine running in gear, VSS inputs received, and PCM detected an unexpected voltage condition on the SSA circuit during the test.

Possible Causes:



SSA control circuit open or shorted to ground
 
SSA control circuit shorted to system power (B+)
 
SSA is damaged or has failed
 
PCM or TCM has failed
 
TSB 3TD008 (3/02) contains information related to this code
 

Trouble Code: P0758

TCM Shift Solenoid 'B' Circuit Malfunction

Trouble Code Conditions: Engine running in gear, VSS inputs received, and PCM detected an open or shorted condition in the SSB circuit during the CCM test.

Possible Causes:



SSB control circuit open or shorted to ground
 
SSB control circuit shorted to system power (B+)
 
SSB is damaged or has failed
 
PCM or TCM has failed
 
TSB 3TD008 (3/02) contains information related to this code
 

Trouble Code: P0765

TCM Overdrive Solenoid Circuit Malfunction

Trouble Code Conditions: Engine running in gear, VSS inputs received, and PCM detected an unexpected voltage condition on the O/D valve circuit during the test.

Possible Causes:



O/D solenoid control circuit open or shorted to ground
 
O/D solenoid control circuit shorted to system power (B+)
 
O/D solenoid valve is damaged or has failed
 
PCM or TCM has failed
 

Trouble Code: P1307

Chassis Acceleration Sensor Range/Performance

Trouble Code Conditions: Vehicle driven to a speed of over 10 mph and then returned to a stop and allowed to idle for 15 seconds, and the PCM detected the Chassis Acceleration Sensor input was not plausible during the test. Note: If DTC P0501 or P1500 is set, repair these trouble codes first.

Possible Causes:



Chassis Acceleration sensor signal circuit is open
 
Chassis Acceleration sensor signal circuit is shorted to ground
 
Chassis Acceleration sensor power circuit is open
 
Chassis Acceleration sensor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P1308

Chassis Acceleration Sensor Low Input

Trouble Code Conditions: Vehicle driven to a speed of over 10 mph, and the PCM detected the Chassis Acceleration Sensor signal was too low during the test. Note: If DTC P0501 or P1500 is set, repair these trouble codes first.

Possible Causes:



Chassis Acceleration sensor signal circuit is shorted to ground
 
Chassis Acceleration sensor power circuit is open
 
Chassis Acceleration sensor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P1309

Chassis Acceleration Sensor High Input

Trouble Code Conditions: Vehicle driven to a speed of over 10 mph, and the PCM detected the Chassis Acceleration Sensor signal was too high during the test. Note: If DTC P0501 or P1500 is set, repair these trouble codes first.

Possible Causes:



Chassis Acceleration sensor signal circuit is shorted to power
 
Chassis Acceleration sensor ground circuit is open
 
Chassis Acceleration sensor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P1386

Knock Sensor Control Zero Test

Trouble Code Conditions: Engine speed over 2200 rpm, ECT sensor signal more than 104°F, engine load more than 3 ms, and the PCM detected an unexpected voltage condition on the Knock Sensor 1 circuit during the test.

Possible Causes:



Knock sensor 1 circuit is open
 
Knock sensor 1 circuit is shorted to ground
 
Knock sensor 1 is damaged or has failed
 
PCM has failed
 

Trouble Code: P1402

Leak Detection Module Pump Circuit Malfunction

Trouble Code Conditions: Ignition OFF.

Possible Causes:



Open or short to ground between leakage detection pump and ECM
 
Short to battery between leakage detection pump and ECM
 
Faulty or damaged leakage detection pump in diagnostic module tank leakage(DMTL)
 

Trouble Code: P1403

Leak Detection Module Solenoid Valve Circuit Malfunction

Trouble Code Conditions: Ignition OFF.

Possible Causes:



Open or short to ground between leakage detection solenoid valve and ECM
 
Short to battery between leakage detection solenoid valve and ECM
 
Faulty or damaged leakage solenoid valve in diagnostic module tank leakage(DMTL)
 

Trouble Code: P1404

Leak Detection Module Heater Malfunction

Trouble Code Conditions: Ignition OFF.

Possible Causes:



Open or short to ground between leakage detection heater and ECM
 
Short to battery between leakage detection heater and ECM
 
Faulty or damaged leakage detection heater in diagnostic module tank leakage(DMTL)
 

Trouble Code: P1446

Leak Detection Pump Solenoid Circuit Malfunction

Trouble Code Conditions: Key on or engine running and the PCM detected an unexpected voltage condition on the Leak Detection Pump circuit (PCM pin 19).

Possible Causes:



LDP power circuit open to the Injector Fuse
 
LDP control solenoid circuit open or shorted to ground
 
LDP control solenoid circuit shorted to system power
 
LDP is damaged or has failed
 
PCM has failed (pump solenoid driver circuit is open or shorted)
 

Trouble Code: P1447

Leak Detection Pump Control Circuit Malfunction

Trouble Code Conditions: Key on or engine running and the PCM detected an unexpected voltage condition on the Leak Detection Pump circuit (PCM pin 20).

Possible Causes:



LDP pump power circuit open to the Injector Fuse
 
LDP motor circuit open or shorted to ground
 
LDP motor circuit is shorted to system power
 
LDP is damaged or has failed
 
PCM has failed (pump motor driver circuit is open or shorted)
 

Trouble Code: P1448

Leak Detection Module Malfunction

Trouble Code Conditions: Key on or engine running and the PCM detected an unexpected voltage condition on the Leak Detection Heater circuit to the module.

Possible Causes:



Leak detection heater circuit is open or shorted to ground
 
Leak detection heater circuit is shorted to system power (B+)
 
Leak detection heater is damaged or has failed
 
PCM has failed
 

Trouble Code: P1458

Air Conditioning Compressor Clutch Circuit Malfunction

Trouble Code Conditions: Engine running and PCM detected an unexpected voltage condition on the A/C Compressor Clutch signal circuit during the test.

Possible Causes:



A/C compressor clutch circuit is open
 
A/C compressor clutch circuit is shorted to ground
 
A/C compressor clutch circuit is shorted to system power
 
PCM has failed
 

Trouble Code: P1500

Vehicle Speed Sensor Performance

Trouble Code Conditions: Engine running OSS signal over 775 rpm, L4 switch indicating "off", and the PCM did not detect any VSS signals during the CCM test.

Possible Causes:



Vehicle speed sensor circuit to the Meter Fuse is open
 
VSS signal ground circuit is open
 
VSS signal circuit is open or shorted to ground
 
VSS signal circuit is shorted to VREF or system power (B+)
 
VSS is damaged or failed, or the speedometer is damaged
 
TSB 2TD004 (8/00) contains information related to this code
 

Trouble Code: P1505

IAC Valve Opening Coil Signal Low

Trouble Code Conditions: Engine runtime over 5 seconds, and the PCM detected the IAC Valve Opening Coil signal remained in a low state during the test.

Possible Causes:



IAC valve control signal is open
 
IAC valve control signal is shorted to ground
 
IAC valve is damaged or has failed
 
PCM has failed (IAC "driver" circuit may be open in the PCM)
 

Trouble Code: P1506

IAC Valve Opening Coil Signal High

Trouble Code Conditions: Engine runtime over 5 seconds, and the PCM detected the IAC Valve Opening Coil signal remained in a high state during the test.

Possible Causes:



IAC valve control signal is shorted to system power (B+)
 
IAC valve is damaged or has failed
 
PCM has failed (IAC "driver" circuit may be shorted in the PCM)
 

 
label.common.footer.alt.autozoneLogo