LaCrosse 2006-2007

Arming The System

Print

Zone 1





Click image to see an enlarged view

Fig. SIR fuse



Click image to see an enlarged view

Fig. Front end sensor

  1. Remove the key from the ignition switch.
  2.  
  3. Connect both front end sensor connectors to each front end sensor.
  4.  
  5. Install both CPA's into each front end sensor connector.
  6.  
  7. Install the radiator upper air baffle and deflector.
  8.  
  9. Install the SIR Fuse.
  10.  
  11. Close the underhood fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 2





Click image to see an enlarged view

Fig. Left roof rail module. Right similar.



Click image to see an enlarged view

Fig. Left side impact sensor. Right similar.

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS proceed to step 3, if the roof rail module needs enabling then go to step 7.
  4.  
  5. Install the left SIS connector (3) to the SIS (1).
  6.  
  7. Install the SIS CPA to the SIS connector (3).
  8.  
  9. Replace and secure the water deflector back over the SIS.
  10.  
  11. Install the left/driver door trim panel.
  12.  
  13. Connect the left roof rail module wiring harness yellow connector (2) to the left roof rail module (3).
  14.  
  15. Install the CPA to the left roof rail module connector (2).
  16.  
  17. Install the left rear panel.
  18.  
  19. Install the SIR Fuse.
  20.  
  21. Close the underhood fuse center cover.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

Zone 3





Click image to see an enlarged view

Fig. Steering wheel module coil yellow connector

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the steering wheel module coil yellow connector (3) to the vehicle harness yellow connector (1).
  4.  
  5. Install the CPA to the steering wheel module coil yellow connector (1).
  6.  
  7. Install the left sound insulator to the I/P (2).
  8.  
  9. Install the SIR Fuse.
  10.  
  11. Close the underhood fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 5





Click image to see an enlarged view

Fig. I/P module yellow connector 

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the I/P module yellow connector (1) to the vehicle harness yellow connector (2).
  4.  
  5. Install the CPA to the I/P module yellow connector (1).
  6.  
  7. Install the right sound insulator to the I/P (3).
  8.  
  9. Install the SIR Fuse.
  10.  
  11. Close the underhood fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 6



  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS proceed to step 3, if the roof rail module needs enabling then go to step 7.
  4.  
  5. Install the right SIS connector to the SIS.
  6.  
  7. Install the SIS CPA to the SIS connector.
  8.  
  9. Replace and secure the water deflector back over the SIS.
  10.  
  11. Install the right/passenger door trim panel.
  12.  
  13. Connect the right roof rail module wiring harness yellow connector to the right roof rail module.
  14.  
  15. Install the CPA to the right roof rail module connector.
  16.  
  17. Install the right rear panel.
  18.  
  19. Install the SIR Fuse.
  20.  
  21. Close the underhood fuse center cover.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

Zone 7



  1. Remove the key from the ignition switch.
  2.  
  3. Connect the left seat belt pretensioner connector to the vehicle wiring harness connector (1).
  4.  
  5. Install the CPA to the seat belt pretensioner connector (1).
  6.  
  7. Install the SIR Fuse.
  8.  
  9. Close the underhood fuse center cover.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

Zone 9



  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the right/passenger seat belt pretensioner proceed to step 3, if the SDM needs enabling then use entire procedure.
  4.  
  5. Connect the seat belt pretensioner-right connector to the vehicle wiring harness connector.
  6.  
  7. Install the CPA to the seat belt pretensioner connector.
  8.  
  9. Connect the right roof rail module wiring harness yellow connector to the right roof rail module.
  10.  
  11. Install the CPA to the right roof rail module connector.
  12.  
  13. Install the right rear panel.
  14.  
  15. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  16.  
  17. Install the CPA to the I/P module yellow connector.
  18.  
  19. Install the right sound insulator to the I/P.
  20.  
  21. Connect the steering wheel module coil yellow connector to the vehicle harness yellow connector.
  22.  
  23. Install the CPA to the steering wheel module coil yellow connector.
  24.  
  25. Install the left sound insulator to the I/P.
  26.  
  27. Connect the seat belt pretensioner-left connector to the vehicle wiring harness connector.
  28.  
  29. Install the CPA to the seat belt pretensioner connector.
  30.  
  31. Connect the left roof rail module wiring harness yellow connector to the left roof rail module.
  32.  
  33. Install the CPA to the left roof rail module connector.
  34.  
  35. Install the left rear panel.
  36.  
  37. Install the SIR Fuse.
  38.  
  39. Close the underhood fuse center cover.
  40.  
  41. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  42.  

 
label.common.footer.alt.autozoneLogo