Mazda Car 2005-06

Removal & Installation

Print

Mazda3



Automatic Control Panel
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the ashtray panel.
  4.  
  5. Remove the decoration panel.
  6.  
  7. Remove the center panel module.
  8.  
  9. Release the left and right tabs and slide the control panel forward.
  10.  
  11. Remove the screws, connector and panel.
  12.  

To install:

  1. Installation is the reverse of removal.
  2.  

Manual Control Panel
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the ashtray panel.
  4.  
  5. Detach the hood release lever from the lower panel.
  6.  
  7. Remove the front scuff plate.
  8.  
  9. Remove the front side trim.
  10.  
  11. Remove the lower panel.
  12.  
  13. Remove the right side front scuff plate.
  14.  
  15. Remove the right side front side trim.
  16.  
  17. Remove the decoration panel.
  18.  
  19. Remove the glove compartment.
  20.  
  21. Remove the passenger junction box and bracket. Unplug the junction box wiring harness clamp from the dashboard.
  22.  
  23. Remove the center panel module.
  24.  
  25. Remove the Remove the wire clamp screws from the A/C unit.
  26.  
  27. Remove the air mix wire and airflow mode wire. Pull the wire in off while pressing the link tab. Remove the E-rings from the air mix wire and airflow mode wire, slide the wires outwards, then remove the wire clamps from the air mix wire and airflow mode wire
  28.  
  29. Release the left and right tabs and remove screw, fan switch connector, climate control connector and unit.

    Click image to see an enlarged view

    Fig. Remove the air mix wire and airflow mode wire-Mazda3

  30.  
  31. Install the wire clamp to the A/C unit.
  32.  
  33. Set the temperature control dial at MAX COLD.
  34.  
  35. Set the airflow mode selector dial at defroster.
  36.  
  37. Install the E-rings to each position on the wires shown in the illustration.

    Click image to see an enlarged view

    Fig. Install the E-rings to each position on the wires shown-Mazda3



    Click image to see an enlarged view

    Fig. Pass each wire through the following routes and connect to A/C unit-Mazda3

  38.  
  39. Pass each wire through the following routes and connect to A/C unit.
  40.  
  41. Connect the climate control unit connectors.
  42.  
  43. Install the climate control unit.
  44.  
  45. Adjust the climate control unit air mix wire as follows:
    1. Set the temperature control dial at middle position (MAX HOT-MAX COLD).
      CAUTION
      If the air mix wire is set without first fixing the air mix link position, it is possible that the air mix door cannot be switched normally.

    2.  
    3. Set the air mix sub link by inserting an #5 Phillips screwdriver into the set hole to fix the position of the link.

      Click image to see an enlarged view

      Fig. Set the air mix sub link by inserting an #5 Phillips screwdriver into the set hole to fix the position of the link-Mazda3



      Click image to see an enlarged view

      Fig. Connect the air mix wire to air mix link-Mazda3



      Click image to see an enlarged view

      Fig. Install the air mix wire to the wire clamp-Mazda3

    4.  
    5. Connect the air mix wire to air mix link.
    6.  
    7. Install the air mix wire to the wire clamp as illustrated.
    8.  
    9. Remove the screwdriver and verify that the temperature control dial can move its full stroke.
    10.  

  46.  
  47. Adjust the climate control unit air mix wire as follows:
    1. Set the airflow mode selector dial at defroster.
      CAUTION
      If the airflow mode wire is set without first fixing the airflow mode main link position, it is possible that the airflow mode door cannot be switched normally.

    2.  
    3. Set the airflow mode main link to the vent position and insert a #5 Phillips screwdriver into the set hole to fix the position of the link.
    4.  
    5. Connect the airflow mode wire to airflow mode link.
    6.  
    7. Install the airflow mode wire to the wire clamp as illustrated.

      Click image to see an enlarged view

      Fig. Install the airflow mode wire to the wire clamp -Mazda3

    8.  
    9. Remove the screwdriver and verify that the airflow mode selector dial can move its full stroke.
    10.  

  48.  

Mazdaspeed6



  1. Disconnect the negative battery cable.
  2.  
  3. Remove the center panel unit.
  4.  
  5. Remove the screws and climate control unit.
  6.  

To install:

  1. Installation is the reverse of removal.
  2.  

MX-5 Miata



  1. Remove the battery cover.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the side wall.
  6.  
  7. Remove the center panel unit.
  8.  
  9. Remove the climate control unit from the center panel unit
  10.  

To install:

  1. Installation is the reverse of removal.
  2.  

 
label.common.footer.alt.autozoneLogo