Mazda Car 2005-06

Sunroof

Print

Power Sunroof



Diagnosis & Testing
Mazda3
  1. Check the sunroof fuses.
  2.  
  3. Apply battery voltage to terminal A, the sunroof should open fully. If not check the sunroof switch.
  4.  
  5. Apply battery voltage to terminal B, the sunroof should close fully. If not check the sunroof switch.
  6.  
  7. Apply battery voltage to terminal B, the sunroof should tilt up. If not check the sunroof switch.

    Click image to see an enlarged view

    Fig. Sunroof motor terminals-Mazda3

  8.  
  9. Apply battery voltage to terminal A, the sunroof should open fully. If not check the sunroof switch.
  10.  
  11. Check the sunroof switch for continuity between terminals G and F, the glass should slide closed. if not replace the switch.
  12.  
  13. Check the sunroof switch for continuity between terminals G and H, the glass should tilt up. if not replace the switch.

    Click image to see an enlarged view

    Fig. Sunroof switch terminals-Mazda3

  14.  

Mazda6 And Mazdaspeed6
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Apply battery voltage to terminals 2A and 2B, the glass should slide close/tilt up. If not replace the switch.
  4.  
  5. Apply battery voltage to terminals 2B and 2A, the glass should slide open/tilt down. If not replace the switch.

    Click image to see an enlarged view

    Fig. Sunroof motor terminals-Mazda6 and Mazdaspeed6

  6.  

Removal & Installation
Motor
Mazda3
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the console on 4 door models.
  4.  
  5. Remove the A-pillar trim.
  6.  
  7. Remove the upper anchor of the front seat belt.
  8.  
  9. Remove the front and rear scuff plates.
  10.  
  11. Remove the B-pillar lower and lower trim.
  12.  
  13. Remove the rear seat.
  14.  
  15. Remove the tire house trim.
  16.  
  17. Remove the trunk side upper trim on 5 door models.
  18.  
  19. Remove the C-pillar trim.
  20.  
  21. Remove the map light.
  22.  
  23. Remove the sun visor.
  24.  
  25. Remove the assist handle.
  26.  
  27. Remove the headliner.
  28.  
  29. Disconnect the sunroof motor connector.
  30.  
  31. Remove the screws, then remove the sunroof motor.
  32.  

To install:

  1. Installation is the reverse of removal.
  2.  

Mazda6 And Mazdaspeed6
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Partially peel back the seaming welt.
  6.  
  7. Remove the microphone, if equipped with a car-navigation system.
  8.  
  9. Remove the microphone sunroof seaming welt.
  10.  
  11. Remove the microphone A-pillar trims.
  12.  
  13. Remove the microphone upper anchor of the front seat belt.
  14.  
  15. Remove the front and rear scuff plates .
  16.  
  17. Remove the B-pillar lower and upper trims.
  18.  
  19. Remove the C-pillar trims.
  20.  
  21. Remove the D-pillar trims, on sport wagon models.
  22.  
  23. Remove thefront and rear map lights.
  24.  
  25. Remove the cargo compartment light .
  26.  
  27. Disconnect the auto-dimming mirror connector.
  28.  
  29. Remove the sun visors.
  30.  
  31. Remove the assist handle.
  32.  
  33. Remove the headliner.
  34.  
  35. Unplug the motor connector.
  36.  
  37. Remove the screws, and then remove the sunroof motor.
  38.  

To install:

  1. Installation is the reverse of removal.
  2.  

Switch
Mazda6 And Mazdaspeed6
  1. Before servicing the vehicle, refer to the precautions section.
  2.  

The sunroof switch and the map light are a single unit.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the screws and the map light from the headliner. Unplug the connector and remove the assembly.
  4.  

To install:

  1. Installation is the reverse of removal.
  2.  

 
label.common.footer.alt.autozoneLogo