Mazda Car 2005-06

Locks & Lock Systems

Print

Power Door Locks



Diagnosis & Testing
  1. Inspect for continuity between the door lock switch terminals using an ohmmeter. There should be continuity when the lock is open and 940-1060 ohms resistance when the lock is closed.
  2.  

Removal & Installation
Door Lock Motor
Mazda3
  1. Remove the door trim.
  2.  
  3. Remove the door glass.
  4.  
  5. Remove the door speaker.
  6.  
  7. Remove the inner handle.
  8.  
  9. Remove the front door unit.
  10.  
  11. Pull the stopper of the front door lock actuator connector.
  12.  
  13. Disconnect the front door lock actuator connector.
  14.  
  15. Remove the front door latch and lock actuator from the front door unit.
  16.  

To install:

  1. Installation is the reverse of removal.
  2.  

Mazda6 And Mazdaspeed6
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Remove the front door unit.
  4.  
  5. Remove the screws, then remove the front door latch and door lock actuator
  6.  

To install:

  1. Installation is the reverse of removal.
  2.  

MX-5 Miata
  1. Remove the door trim.
  2.  
  3. Remove the door glass.
  4.  
  5. Remove the door speaker.
  6.  
  7. Remove the door unit by unplugging the electrical connections, unfastening the screws and remove the unit. Door
  8.  
  9. Disconnect the cables from the inner handle and the door lock knob.
  10.  
  11. Disconnectthe rods from the key cylinder and the outer handle.
  12.  
  13. Remove the screws, then remove the door latch and lock actuator.
  14.  

To install:

  1. Installation is the reverse of removal.
  2.  

Door Lock Switch
Mazda6 And Mazdaspeed6
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Open the front door glass so that the distance from the top of the front door glass to the upper part of the front beltline molding is 8.3 inch (210mm).
  4.  
  5. Disconnect the negative battery cable.
  6.  
  7. Open the inner handle cap using a small screwdriver, then remove the screw.
  8.  
  9. Remove the inner handle cover.
  10.  
  11. Disconnect the door lock switch connector.
  12.  
  13. Remove the inner garnish.
  14.  
  15. Remove the cover, then remove the screw.
  16.  
  17. Remove the lens cover, then remove screw.
  18.  
  19. Disengage the clips from the front door using a fastener remover.
  20.  
  21. Pull the front door trim upward, then disengage the tabs from the front door.
  22.  
  23. Disconnect the power door mirror switch connector and the power window main switch connector.
  24.  
  25. Remove the courtesy light.
  26.  
  27. Remove the front door trim.
  28.  
  29. Remove the switch panel from the front door trim
  30.  
  31. Remove the hole cover.
  32.  
  33. Remove the screws.
  34.  
  35. Lift out the front door glass.
  36.  
  37. Remove the front door speaker.
  38.  
  39. Disconnect the power window motor connector, front door lock actuator connector, and the power outside mirror connector.
  40.  
  41. Remove the front door harness from the front door unit.
  42.  
  43. Remove screws
  44.  
  45. Remove the front door actuator tab from the front door unit.
  46.  
  47. Pull the front door unit slightly outward, and while keeping the power window regulator from
  48.  
  49. Catching on the front door, remove the front door unit from the front door.
  50.  
  51. Pull out the inner handle cable and door lock knob cable from the hole.
  52.  
  53. Remove the power window motor and power window regulator from the front door unit carrier.
  54.  
  55. Remove the screws, then the front door latch and door lock actuator.
  56.  

To install:

  1. Installation is the reverse of removal.

    Click image to see an enlarged view

    Fig. Power window mounting-Mazda6 and Mazdaspeed6



    Click image to see an enlarged view

    Fig. Window regulator-Mazda6 and Mazdaspeed6

  2.  

MX-5 Miata
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the door trim.
  4.  
  5. Remove the screws, then remove the door lock switch.
  6.  

To install:

  1. Installation is the reverse of removal.
  2.  

 
label.common.footer.alt.autozoneLogo