Mazda Tribute 2001-06

Removal & Installation

Print

2.0L And 2.3L Engines



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the accessory drive belt.

    Click image to see an enlarged view

    Fig. Identifying electrical connector

  6.  
  7. Disconnect the electrical connector.
    NOTE
    Drain the power steering fluid into a suitable drain pan.



    Click image to see an enlarged view

    Fig. Identifying the power steering pressure line

  8.  
  9. Disconnect the power steering pressure line.

    Click image to see an enlarged view

    Fig. Identifying lower power steering pump bolts

  10.  
  11. Remove the lower power steering pump bolts.
  12.  
  13. Lower the vehicle.

    Click image to see an enlarged view

    Fig. Identifying power steering pressure line bracket bolt

  14.  
  15. Remove the power steering pressure line bracket bolt.

    Click image to see an enlarged view

    Fig. Disconnecting power steering low pressure hose

  16.  
  17. Disconnect the power steering low pressure hose.

    Click image to see an enlarged view

    Fig. Removing power steering pump bolts

  18.  
  19. Remove the bolts and the power steering pump.

    Click image to see an enlarged view

    Fig. Removing power steering pump pulley

  20.  
  21. Using the special tool 211-016, remove the power steering pump pulley.
  22.  

To install:


CAUTION
Install a new power steering pump pulley after the second removal and installation. Inspect the pulley for paint marks in the web area near the hub. If there are two paint marks, install a new pulley. If there is no paint or one paint mark, use a paint pencil to mark the web area of the pulley near the hub.



Click image to see an enlarged view

Fig. Installing power steering pump pulley

  1. Using the special tool 211-185, install the power steering pump pulley.

    Click image to see an enlarged view

    Fig. Installing a new seal on the power steering pressure hose fitting

  2.  
  3. Using the special tool 211-D027, install a new seal on the power steering pressure hose fitting. Remove and discard the original seal. Stretch the seal over the seal replace and slide it onto the tube nut.

    Click image to see an enlarged view

    Fig. Installing upper bolts

  4.  
  5. Position the power steering pump and install the upper bolts.
  6.  
  7. Connect the power steering low pressure hose.

    Click image to see an enlarged view

    Fig. Installing the power steering pressure line bracket and bolt

  8.  
  9. Position the power steering pressure line bracket and install the bolt.
  10.  
  11. Raise the vehicle.

    Click image to see an enlarged view

    Fig. Installing lower power steering pump bolts

  12.  
  13. Install the lower power steering pump bolts.

    Click image to see an enlarged view

    Fig. Connecting power steering pressure line

  14.  
  15. Connect the power steering pressure line.
  16.  
  17. Connect the electrical connector.
  18.  
  19. Install the drive belt.
  20.  
  21. Connect the negative battery cable.
  22.  
  23. Fill, bleed and leak check the power steering system.
  24.  

3.0L Engine



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Drain power steering system.

    Click image to see an enlarged view

    Fig. Supporting Engine

  6.  
  7. Using the special tools 303-050 and 303-F072, support the engine.

    Click image to see an enlarged view

    Fig. Identifying power steering pump pulley bolt

  8.  
  9. Loosen the power steering pump pulley bolt.
  10.  
  11. Remove the drive belt.
  12.  
  13. Remove the bolt and the power steering pump pulley.
    NOTE
    Drain the power steering fluid into a suitable drain pan.



    Click image to see an enlarged view

    Fig. Identifying power steering pressure line bracket bolt (1), electrical connector (2) and power steering pressure line (3)

  14.  
  15. Remove the power steering pressure line bracket bolt.
  16.  
  17. Disconnect the electrical connector.
  18.  
  19. Disconnect the power steering pressure line and position aside.

    Click image to see an enlarged view

    Fig. Removing ground cable nut

  20.  
  21. Remove the nut and position the ground cable aside.

    Click image to see an enlarged view

    Fig. Removing upper engine insulator bracket bolt

  22.  
  23. Remove the upper engine insulator bracket bolt.

    Click image to see an enlarged view

    Fig. Identifying A/C line support nut

  24.  
  25. Remove the A/C line support nut.
    NOTE
    The engine isolator bracket is shown removed for clarity.



    Click image to see an enlarged view

    Fig. Removing the engine insulator nut (1) and bolts (2)

  26.  
  27. Remove the engine insulator nut.
  28.  
  29. Remove the bolt and the engine insulator.

    Click image to see an enlarged view

    Fig. Identifying pressure line bracket screw (1), nuts (2) and bolts (3)

  30.  
  31. Remove the pressure line bracket screw.
  32.  
  33. Remove the six nuts.
  34.  
  35. Remove five bolts and the power steering pump bracket.

    Click image to see an enlarged view

    Fig. Removing power steering pump

  36.  
  37. Remove the power steering pump.
  38.  

To install:

Click image to see an enlarged view

Fig. Installing the power steering pump components

  1. Position the power steering pump.
  2.  
  3. Install the power steering pump bracket, five bolts, six nuts and pressure line bracket screw.

    Click image to see an enlarged view

    Fig. Installing the engine insulator components

  4.  
  5. Install the engine insulator, bolts and nuts.

    Click image to see an enlarged view

    Fig. Installing the upper engine insulator bracket bolt

  6.  
  7. Install the upper engine insulator bracket bolt.
  8.  
  9. Position the A/C line support and install the nut.

    Click image to see an enlarged view

    Fig. Installing ground cable and nut.

  10.  
  11. Install the ground cable and nut.
  12.  
  13. Using the special tool, install a new seal on the power steering pressure hose fitting. Remove and discard the original seal. Stretch the seal over the special tool and slide it onto the tube nut.

    Click image to see an enlarged view

    Fig. Installing the power steering pressure hose components

  14.  
  15. Connect the power steering pressure hose. Connect the power steering pressure hose to the pump. Connect the electrical connector. Install the power steering pressure line bracket bolt.
  16.  
  17. Connect the power steering low pressure hose.
  18.  
  19. Install the power steering pump pulley and bolt.
  20.  
  21. Install the drive belt.
  22.  
  23. Torque the power steering pump pulley bolt to 36 ft. lbs. (49 Nm)
  24.  
  25. Lower the vehicle and remove the special tools 303-050 and 303-F072.
  26.  
  27. Fill, bleed and leak check the power steering system.
  28.  



Click image to see an enlarged view

Fig. Identifying power steering system components


CAUTION
While repairing the power steering system, care should be taken to prevent the entry of contaminants or premature failure of the power steering components can result.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Drain the power steering fluid into a suitable drain pan. Rotate the accessory drive belt tensioner counterclockwise and position the accessory drive belt aside.
  6.  
  7. Release the clamp and remove the power steering fluid suction hose from the power steering pump.
  8.  
  9. Disconnect the power steering pressure line fitting nut from the power steering pump.
  10.  
  11. Remove the 3 power steering pump bolts.
    CAUTION
    Do not let the flow control valve fall out of the power steering pump.

  12.  
  13. Remove the power steering pump.
  14.  
  15. To install, reverse the removal procedure. Torque all fasteners to specification.
  16.  
  17. Fill, bleed and leak check the power steering system.
  18.  

 
label.common.footer.alt.autozoneLogo