Mazda Trucks 1994-1998 Repair Guide

Seats

Print

REMOVAL & INSTALLATION



Navajo and B Series Pick-up
BENCH SEAT

See Figure 1



Click image to see an enlarged view

Fig. Fig. 1: B Series Pick-up bench seat

  1. On the right side, remove the seat track insulator.
  2.  
  3. Remove 4 seat track-to-floor retaining screws (2 each side) and lift the seat and track assembly from vehicle.
  4.  
  5. To remove the tracks from the seat, place the seat upside-down on a clean bench.
  6.  
  7. Disconnect the track latch tie rod assembly from latch lever and hook in the center of the cushion assembly.
  8.  
  9. Remove 4 track-to-seat cushion retaining screws (2 each side) and remove the tracks from the cushion assembly.
  10.  

To install:
  1. Position the track to the cushion assembly. Install the 4 track-to-seat retaining screws and tighten.
  2.  
  3. Connect the track latch tie rod assembly to the latch lever and hook in center of cushion.
  4.  
  5. Position the seat and track assembly in the vehicle.
  6.  
  7. Install the 4 seat track-to-floor retaining screws and tighten to specification.
  8.  
  9. On the right side, install the seat track insulator.
  10.  

BUCKET & 60/40 SEATS

See Figures 2, 3 and 4



Click image to see an enlarged view

Fig. Fig. 2: B Series Pick-up bucket seat



Click image to see an enlarged view

Fig. Fig. 3: Navajo bucket seat



Click image to see an enlarged view

Fig. Fig. 4: 60/40 split seat-Navajo

  1. Remove the seat track insulator (B Series Pick-up passenger seat only).
  2.  
  3. Remove the 4 seat track-to-floorpan screws (2 each side) and lift the seat and track assembly from the vehicle.
  4.  
  5. To remove the seat tracks from the seat cushion, position the seat upside down on a clean bench.
  6.  
  7. Disconnect the latch tie rod assembly and assist spring from the tracks.
  8.  
  9. Remove 4 track-to-seat cushion screws (2 each side) from the track assemblies. Remove the tracks from seat cushion.
  10.  

To install:
  1. Position the tracks to the seat cushion. Install the 4 track-to-seat cushion screws (2 each side) and tighten.
  2.  
  3. Connect the latch tie rod assembly and assist spring to the tracks.
  4.  
  5. Position the seat and track assembly in the vehicle.
  6.  
  7. Install 4 track-to-floorpan screws and tighten to specification.
  8.  
  9. Install the seat track insulators (B Series Pick-up passenger seat only).
  10.  

MPV Models
DRIVER'S SEAT

See Figure 5

  1. Remove the fuel filler lid opener.
  2.  
  3. Remove the parking brake lever.
  4.  
  5. Remove the seat bracket covers.
  6.  
  7. Remove the seat leg covers.
  8.  
  9. Remove the seat bracket-to-floor bolts and lift out the seat.
  10.  
  11. Installation is the reverse of removal. Torque the bracket-to-floor bolts to 25-41 ft. lbs. (34-56 Nm).
  12.  



Click image to see an enlarged view

Fig. Fig. 5: Front seat components

FRONT RIGHT SEAT

See Figure 5

  1. Remove the jack cover.
  2.  
  3. Remove the jack and jack handle.
  4.  
  5. Remove the seat bracket covers.
  6.  
  7. Remove the seat leg covers.
  8.  
  9. Remove the seat bracket-to-floor bolts and lift out the seat.
  10.  
  11. Installation is the reverse of removal. Torque the bracket-to-floor bolts to 25-41 ft. lbs. (34-56 Nm).
  12.  

NO. 1 REAR SEAT

See Figure 6



Click image to see an enlarged view

Fig. Fig. 6: No. 1 rear seat components

The seat is removed by simply unlatching the release levers on the seat legs.

NO. 2 REAR SEAT

See Figure 7



Click image to see an enlarged view

Fig. Fig. 7: No. 2 rear seat and seat mounts

  1. Remove the seat bracket cover.
  2.  
  3. Remove the folding link bolts.
  4.  
  5. Remove the rear hinge bolts.
  6.  
  7. Remove the front hinge bolts.
  8.  
  9. Lift out the seat.
  10.  
  11. Installation is the reverse of removal. Torque all bolts to 16-22 ft. lbs. (22-30 Nm).
  12.  

 
label.common.footer.alt.autozoneLogo