Metro, Prizm 2000-2002

Multi-Function (Combination) Switch

Print

Removal & Installataion



  1. Disconnect the negative battery cable.
  2.  
  3. Disable the Supplemental Inflatable Restraint (SIR) system, as outlined in the Chassis Electrical Section.
  4.  
  5. Remove the knee bolster.
  6.  
  7. Remove the steering wheel from the column.
  8.  
  9. Loosen the 2 upper steering column mounting bolts.
  10.  
  11. Slightly lower the steering column.
  12.  
  13. Remove the 5 screws from the lower steering column cover in order to remove the upper cover and the lower cover.
  14.  
  15. Disconnect the SIR coil and the combination switch electrical connectors.
  16.  
  17. Loosen the SIR coil and combination switch electrical harness wire bands.
  18.  
  19. Remove the 3 screws in order to remove the SIR coil and the combination switch from the column.

    Click image to see an enlarged view

    Fig. Combination (multi-function) switch removal-Metro

  20.  

To install:

  1. Use the 3 screws in order to install the SIR coil and the combination switch to the column.
  2.  
  3. Connect the SIR coil and the combination switch electrical connectors (2).
  4.  
  5. Secure the harness to the column with the wire bands.
  6.  
  7. Install the upper column cover (1) and the lower column cover (2).
  8.  
  9. Secure the column covers with the 5 screws.
  10.  
  11. Tighten the 2 upper steering column mounting bolts to 10 ft. lbs. (14 Nm).
  12.  
  13. Install the knee bolster.
  14.  
  15. Install the lower trim cover to the steering column.
  16.  
  17. Secure the lower trim cover with the 3 screws.
  18.  
  19. Install the steering wheel to the steering column.
  20.  
  21. Enable the SIR system, as outlined in the Chassis Electrical Section.
  22.  
  23. Connect the negative battery cable.
  24.  

  1. Disconnect the negative battery cable.
  2.  
  3. Disable the Supplemental Inflatable Restraint (SIR) system, as outlined in the Chassis Electrical Section.
  4.  
  5. Remove the lower trim cover screws and the 2 lower trim cover screws that are located beneath the steering wheel.
  6.  
  7. Remove the steering column lower trim cover (6).
  8.  
  9. Remove the steering column upper trim cover screw and upper trim cover from the steering column (7).
  10.  
  11. Inspect the base for damage. If damage to the base is observed, replace the turn signal, headlamp and windshield washer switch as an assembly.
  12.  
  13. Disconnect the wiper/washer switch electrical connector.
  14.  
  15. Remove the 2 screws and the wiper/washer switch (5).

    Click image to see an enlarged view

    Fig. Steering wheel and turn signal/headlamp and wiper/washer switch (5) components-Prizm

  16.  

To install:

  1. Install the wiper/washer switch to the steering column. Secure the switch with the 2 screws.
  2.  
  3. Connect the wiper/washer switch electrical connector.
  4.  
  5. Install the steering column upper trim cover to the vehicle (7). Secure the trim cover with the screw.
  6.  
  7. Install the steering column lower trim cover to the vehicle (6). Secure the trim cover with the 3 screws.
  8.  
  9. Enable the SIR system, as outlined in the Chassis Electrical Section.
  10.  
  11. Connect the negative battery cable.
  12.  

 
label.common.footer.alt.autozoneLogo