Log In
Search suggestions

    My Vehicles

    Add a Vehicle

    Find a Store

    Select Store

    SAVE 20% + GET A $10 GIFT CARD ON ONLINE SHIP-TO-HOME ORDERS OVER $100.

    Use Code: FALLBACK

    See Details

    Mitsubishi Galant/Mirage/Diamante 1990-2000

    Antenna

    Print

    REPLACEMENT



    1990-92 Mirage


    Click image to see an enlarged view

    Fig. Antenna mounting-1990-92 Mirage


    NOTE
    The mast may be replaced separately by simply unscrewing it from the base. The following procedure is for replacing the base and cable as a unit.

    1. Raise and safely support the vehicle securely on jackstands.
    2.  
    3. Remove the passenger side front wheel.
    4.  
    5. Remove the splash shield inside the passenger side front wheel arch.
    6.  
    7. Remove the center panel (for radio access) and remove the glove box.
    8.  
    9. Remove the right side sill plate and remove the kick panel.
    10.  
    11. If the car has a rear heater, remove the shower duct under the glove box.
    12.  
    13. Carefully remove the PCM. For more details, please refer to .
    14.  
    15. Remove the radio and disconnect the antenna cable.
    16.  
    17. Release the cable from the bands and clips holding it under the dash.
    18.  
    19. Unscrew the mast from the antenna base.
    20.  
    21. Remove the upper base mounting nut (at the fender) and disconnect the lower bolt holding the mast. Remove the mast and carefully remove the cable.
    22.  
    23. Install the new unit, tightening both the upper nut and lower bolt.
    24.  
    25. Carefully feed the cable into the car and route it to the radio. Engage the cable in the clips and install new retaining bands.
    26.  
    27. Connect the antenna cable to the radio and reinstall the radio.
    28.  
    29. Replace the MPI control unit.
    30.  
    31. Install the heater duct, if it was removed, and install the kick panel on the right side.
    32.  
    33. Install the sill plate. Install the glove box.
    34.  
    35. Install the center panel.
    36.  
    37. Reinstall the wheel arch splash shield. Install the wheel if it was removed. Lower the car to the ground.
    38.  

    1993-00 Mirage


    Click image to see an enlarged view

    Fig. Antenna mounting-1993-00 Mirage

    1. Disconnect the negative battery cable.
    2.  
    3. Remove the antenna base retaining screws.
    4.  
    5. Lift the base and mast assembly up from the roof.
    6.  
    7. Detach the connector for the antenna.
    8.  
    9. The installation is the reverse of removal.
    10.  

    Galant and Diamante


    Click image to see an enlarged view

    Fig. Antenna mounting-Galant



    Click image to see an enlarged view

    Fig. Antenna mounting-Diamante

    1. Disconnect the negative battery cable.
    2.  
    3. Remove the side trim from the trunk.
    4.  
    5. On a non-power antenna, unscrew the mast.
    6.  
    7. Carefully remove the ring nut from the fender top.
    8.  
    9. Detach the wiring for the electric motor and the antenna cable connection.
    10.  
    11. Remove the nuts and bolts holding the motor to the body, then remove the motor.
    12.  

    To install:

    1. Install the new motor and tighten the mounting nuts and bolts.
    2.  
    3. Attach the wiring connectors for the antenna cable and the motor.
    4.  
    5. Install the ring nut and tighten it only to 3 ft. lbs. (4 Nm).
    6.  


    NOTE
    This is little more than finger tight; do not overtighten this nut.

    1. On a non-power antenna, install the mast.
    2.  
    3. Install the trim panels in the trunk.
    4.  

     
    AutoZone Logo