Mitsubishi Pick-ups and Montero 1983-1995 Repair Guide

Carburetors

Print

ADJUSTMENTS



Accelerator Cable
  1. Warm the engine up completely and make certain the high idle cam is not engaged.
  2.  
  3. Check the action of the accelerator pedal. There should be little to no free-play between the normal "at rest" position and the point that engine speed begins to increase. Correct free-play measurement is 0-0.8 in. (0-20mm).
  4.  
  5. If there is excessive free-play, loosen the cable adjusting nuts located on the cable mount on the carburetor. With both nuts loosened, the cable may be adjusted to remove slack. Do not adjust the cable beyond the point of no free-play; the engine idle speed will be changed.
  6.  

Float and Fuel Level

See Figures 1 and 2

  1. Remove the top of the carburetor and remove the gasket. The carburetor does not need to be removed for this procedure. Follow the directions within the carburetor overhaul procedure later in this section.
  2.  
  3. Hold the carburetor top and float upside down. Use a float gauge or depth gauge to measure the distance from the bottom of the float (now the top, since it's upside down) to the inside of the carburetor top. The correct distance is 0.76-0.84 in. (19-21mm).
  4.  
  5. If the dimension is not correct, the shim below the needle seat must be changed. Use a thicker shim to increase the measurement (or lower the float level) or a thinner shim to decrease the measurement (raise the float level).
  6.  
  7. The shim kit contains 3 shims: 0.3mm, 0.4mm and 0.5mm. The float measurement will change by 3 times the measurement of the shim installed or removed. Shims may be combined as necessary. Some arithmetic after measuring should provide the correct shim thickness on the first try.
  8.  
  9. To replace the shim, remove the float pin and the float. Remove the needle valve.
  10.  
  11. Use a pair of pliers to gently unscrew the seat at its widest point. Take great care not to damage the seat or the surrounding metal.
  12.  
  13. Slip the shim(s) over the narrow portion of the seat and then reinstall the seat. Gently tighten it without damage.
  14.  
  15. Reassemble the needle valve and float.
  16.  
  17. Re-measure the float height and replace the shim(s) if necessary to get the correct height.
  18.  
  19. Reinstall the carburetor top.
  20.  



Click image to see an enlarged view

Fig. Fig. 1: Sets of shims are available for adjusting float height-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 2: The shims fit under the seat of the needle valve-feedback carburetor

Throttle Opener
1983-87 PICK-UP AND 1983-86 MONTERO

See Figures 3, 4 and 5

  1. Disconnect the vacuum hose running to the throttle opener port.
  2.  
  3. Connect a hand vacuum pump to the nipple of the throttle opener. Install a tachometer to read engine speed. Make certain the idle speed for the engine is set correctly.
  4.  
  5. Run the engine at curb idle (fully warm). Apply 11.8 in. Hg (39.8 kPa) with the hand pump; idle speed should increase to 900-950 rpm. If the idle does not increase, replace the dashpot/throttle opener assembly.
    1. Remove the throttle return spring from the throttle lever.
    2.  
    3. Disconnect the throttle opener rod from the free lever.
    4.  
    5. Remove the two attaching screws and remove the throttle opener/dashpot assembly.
    6.  
    7. Install the new unit, connect the rod and install the spring.
    8.  

  6.  
  7. Reconnect the vacuum hose to the nipple. Start the engine, run it at curb idle and turn the air conditioning on. Idle speed should increase to 900-950 rpm.
  8.  
  9. If the throttle opener needs adjustment, do so by turning the screw on the throttle opener/dashpot assembly. Don't turn any other screws to adjust the throttle opener; the curb idle or other important settings may be affected.
  10.  



Click image to see an enlarged view

Fig. Fig. 3: The location of the throttle opener adjusting screw. Do not adjust SAS 1 or 3-1983-87 Pick-ups and 1983-86 Monteros



Click image to see an enlarged view

Fig. Fig. 4: Adjusting the throttle opener-1983-87 Pick-ups and 1983-86 Monteros



Click image to see an enlarged view

Fig. Fig. 5: The location of the throttle opener setting screw-1983-87 Pick-ups and 1983-86 Monteros

1988-89 PICK-UP AND 1987-90 MONTERO
  1. Identify the vacuum control solenoid on the firewall. Label and carefully remove the two vacuum hoses running to the unit.
  2.  
  3. Disconnect the electrical connector from the solenoid.
  4.  
  5. Connect a hand vacuum pump to the solenoid port which held the vacuum hose with the white stripe.
  6.  
  7. Using jumper wires, connect battery voltage to one terminal of the solenoid and connect the other terminal to a good ground.
  8.  
  9. With battery voltage applied to the solenoid, draw vacuum with the hand pump. Use the chart to check the properties of the valve with proper combinations of vacuum and electricity applied or removed.
  10.  
  11. Remove the 12 volt jumpers. Use an ohmmeter to measure the resistance of the solenoid. Resistance should be 40-46 ohms at 68°F (20°C).
  12.  
  13. If the solenoid does not behave correctly under ALL test conditions, it must be replaced.
  14.  

REMOVAL & INSTALLATION




CAUTION
Gasoline in either liquid or vapor state is EXTREMELY explosive. Take great care to contain spillage. Work in an open or well-ventilated area. Do not connect or disconnect electrical connectors while fuel hoses are removed or loosened. Observe no smoking/no open flame rules during repairs. Have a dry-chemical fire extinguisher (type B-C) within arm's reach at all times and know how to use it.

Non-Feedback Models

All 1983-84 non-diesel Pick-ups, as well as 1983 Monteros and 1984 non-California Monteros, were equipped with a non-feedback carburetor.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the air cleaner.
  4.  
  5. Place a container under the fuel line inlet fitting to contain spillage. Disconnect the fuel inlet line from the carburetor nipple.
  6.  
  7. Label or diagram each vacuum hose connection; disconnect the hoses from the carburetor ports.
  8.  
  9. Disconnect the throttle cable at the carburetor.
  10.  
  11. Remove the mounting bolts. Lift the carburetor off the engine and remove it to a workbench. Keep it level to avoid spilling fuel from the float bowl.
  12.  
  13. Carefully drain the carburetor into a container with an airtight lid.
  14.  
  15. Before installation, inspect the mating surfaces of the carburetor and manifold. They should be clean and free of nicks, burrs or any pieces of gasket material. Clean the surfaces as necessary and remove any slight imperfections with crocus or emery cloth.
  16.  
  17. Put a new carburetor gasket on the surface of the manifold.
  18.  
  19. Carefully locate the carburetor on top of the gasket with all holes lined up. Install the carburetor bolts, tightening them alternately and evenly in small increments. The gasket must be compressed evenly to prevent leakage.
  20.  
  21. Connect the throttle linkage. Have someone depress the accelerator pedal and make sure the throttle blade opens all the way; it should be exactly vertical at full throttle. Adjust the cable as needed to obtain full opening of the throttle plate.
  22.  
  23. Connect the vacuum hoses according to your drawing or labeling. Make sure all are soft and free of cracks to make a good seal. Replace hoses that are hard or cracked.
  24.  
  25. Reconnect the fuel hoses.
  26.  
  27. Reinstall the air cleaner assembly. Check the filter element and replace it if needed.
  28.  
  29. Connect the negative battery cable.
  30.  
  31. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  32.  
  33. Start the engine. It will require a longer cranking period and two or three pumps of the accelerator pedal before it starts.
  34.  


CAUTION
Do NOT prime the engine by pouring fuel into the air horn of the carburetor. This outdated and foolish practice can result in severe injury or damage.

  1. While the engine is warming up, check the work area carefully for any sign of fuel or vacuum leaks and attend to them immediately. Set the idle speed and make other necessary adjustments after the engine is running smoothly and is fully warmed up.
  2.  

Feedback Models

All 1985-89 Pick-ups and Monteros, as well as 1984 California Monteros and 1990 4-cylinder Monteros, were equipped with a feedback carburetor.

  1. Disconnect the negative battery cable.
  2.  

All wires and hoses should be labeled at the time of removal. The amount of time saved during reassembly makes the extra effort well worthwhile.

  1. Drain the engine coolant to a point below the level of the intake manifold.
  2.  


CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  1. Remove the air cleaner assembly, disconnecting the various hoses and ducts as necessary.
  2.  
  3. Disconnect the accelerator cable from the carburetor.
  4.  
  5. Disconnect the coolant hose connection from the back of the carburetor.
  6.  
  7. Disconnect the vacuum hoses.
  8.  
  9. For vehicles with automatic transmissions, remove the lock pin and disconnect the throttle control cable linkage.
  10.  
  11. Disconnect the wiring to the throttle position sensor.
  12.  
  13. Disconnect the wiring to the solenoid valve.
  14.  
  15. Unplug the connector for the carburetor heater. Take care to separate the connectors without pulling on the wiring.
  16.  
  17. Use a small pan or jar to hold under the fuel hose connections. Disconnect them one at a time and catch any spilled fuel.
  18.  
  19. Remove the carburetor retaining bolts and lift the carburetor off the engine. Keep the carburetor level to avoid spillage. Once the carburetor is clear of the car, drain the remaining fuel into a container with an airtight lid.
  20.  
  21. Remove the carburetor base gasket (insulator). If desired, remove the heater element. Handle the heater carefully, protecting it from impact or pulling on the wire.
  22.  
  23. Before installation, inspect the mating surfaces of the carburetor and manifold. They should be clean and free of nicks, burrs or any pieces of gasket material. Clean the surfaces as necessary and remove any slight imperfections with crocus or emery cloth.
  24.  
  25. Reinstall the heater element and put a new carburetor gasket on the surface of the manifold.
  26.  
  27. Carefully locate the carburetor on top of the gasket with all holes lined up. Install the carburetor bolts, tightening them alternately and evenly in small increments. The gasket must be compressed evenly to prevent leakage. Tighten the bolts to 13 ft. lbs. (18 Nm).
  28.  
  29. Connect the wiring harness to the heater element, the solenoid valve and the throttle position sensor.
  30.  
  31. If equipped with an automatic transmission, connect the throttle control cable and install the locking pin securely.
  32.  
  33. Connect the vacuum hoses, inspecting each one for any sign of cracking or hardening. If a hose is suspect, replace it.
  34.  
  35. Install the coolant hose and secure the clamp.
  36.  
  37. Connect the accelerator cable.
  38.  
  39. Reinstall the air cleaner, connecting the hoses and ductwork as necessary. Make certain the air cleaner body is properly seated on the carburetor and that each hose is firmly attached.
  40.  
  41. Refill the cooling system with coolant.
  42.  
  43. Connect the negative battery cable.
  44.  
  45. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  46.  
  47. Start the engine. It will require a longer cranking period and two or three pumps of the accelerator pedal before it starts.
  48.  


CAUTION
Do NOT prime the engine by pouring fuel into the air horn of the carburetor. This outdated and foolish practice can result in severe injury or damage.

  1. While the engine is warming up, check the work area carefully for any sign of fuel, coolant or vacuum leaks and attend to them immediately. Set the idle speed and make other necessary adjustments to the accelerator or throttle control cables after the engine is running smoothly and is fully warmed up.
  2.  

OVERHAUL



Non-Feedback Models

The carburetor is comprised of three main sections: the top or float bowl cover, the main body and the throttle body or base. Separating these sections requires the removal and installation of many small parts and fittings. Do not disassemble anything unnecessarily. Some important components are not removed or adjusted during an overhaul.

  1. Remove the carburetor from the car, following the instructions earlier in this section. Drain any remaining fuel into a container with an airtight lid. Place the carburetor on the workbench in a clean, dry area. Placing it on a large, lint-free cloth will help prevent parts from getting lost or rolling around.
  2.  
  3. Remove the coolant hose from the throttle body and from the wax element.
  4.  
  5. Using a small hand grinder or similar tool, remove the heads from the two lock screws in the choke cover.
  6.  
  7. Disconnect the fuel cut-off solenoid ground wire from the top of the carburetor.
  8.  
  9. Remove the throttle return spring and the damper spring.
  10.  
  11. Disconnect the vacuum hose running from the depression chamber to the throttle body.
  12.  
  13. Remove the accelerator pump rod from the throttle lever.
  14.  
  15. Remove the dashpot rod (for manual transmission) or the throttle opener rod (automatic transmission) from the free lever.
  16.  
  17. Remove the depression chamber rod from the secondary throttle lever.
  18.  
  19. Remove the six screws from the carburetor top. The four outer ones connect to the main body of the carburetor; the two bolts within the air passage connect to the throttle body.
  20.  

Many of the screws use Phillips-type heads. Use a screwdriver which fits the head exactly. An improper tool can damage the head of the screw and cause problems during reassembly.

  1. Remove the main body with the top attached (the top cannot come free yet) by lifting straight up. Do not turn the carburetor upside down during the removal; if it is inverted, the accelerator pump check weight, ball and steel ball of the anti-overfill device will fall out.
  2.  
  3. Remove the E-clip from the lower end of the choke unloader rod and disconnect the rod from the lever.
  4.  
  5. Separate the top from the main body.
  6.  
  7. At this point, the carburetor is disassembled enough to perform common overhaul replacements. Do not disassemble any further components without good diagnostic reasons. In particular, do not disassemble the automatic choke system or attempt to remove the throttle plates; both systems require very precise alignment which is beyond the ability of the home mechanic.
  8.  
  9. Remove the float from the float arm by removing the pivot pin.
  10.  
  11. Inspect the float bowl for any sign of particulate dirt or solid matter. Carefully wipe the bowl clean. Shake the float, listening for any sign of liquid fuel inside. If the float has absorbed fuel, it must be replaced.
  12.  
  13. Remove the retaining screw and bracket holding the needle valve. Carefully remove the needle valve and inspect it for uneven wear or pitting. (A magnifying glass is very helpful for checking the tip.) Check the seat for signs of pitting. Don't remove the seat without planning to replace it; if it looks OK, leave it alone. If the seat is to be removed, it must be carefully unscrewed with pliers. It will be difficult to loosen and care must be take not to damage or deform the seat. When the seat is removed, the spacing shim below it must be recovered and reinstalled. This shim determines float level adjustment.
  14.  
  15. Remove the accelerator pump and the fuel cut-off solenoid. Remove the check weight and ball.
  16.  
  17. Wearing eye protection and gloves, carefully clean the fuel and air passages with a spray cleaner and, if available, compressed air. A majority of carburetor problems are caused by very small bits of dirt lodging in the air or fuel passages. Clean everything thoroughly.
  18.  
  19. Inspect the motion of both the choke and throttle plates. They must move smoothly with absolutely no sign of binding or notching. Clean the linkages and plates as necessary, then apply a small amount of lubricant to the pivot points.
  20.  
  21. If any of the fuel jets are to be replaced due to wear or etching, they must be replaced with the identical item. Each jet has a number on the side of it to aid in identification. (The jets are selected based on precise airflow measurements during assembly. Installation of the wrong jet will send the wrong fuel mixture to the engine under almost all conditions).
  22.  
  23. Install the accelerator pump, the fuel cut-off solenoid and the check weight and ball.
  24.  
  25. Install the needle valve and its retainer.
  26.  
  27. Hold the float in position and install the pivot pin.
  28.  
  29. Carefully place the carburetor top onto the main body and install the four retaining screws holding the top to the body.
  30.  
  31. Install the choke unloader rod to the lever and install the E-ring to hold the rod in place.
  32.  

Be careful that the E-ring does not spring out of place during installation.

  1. Install the two screws through the air horn and tighten them.
  2.  
  3. Install the depression chamber rod to the secondary throttle lever.
  4.  
  5. Connect the dashpot or throttle opener rod to the free lever.
  6.  
  7. Install the accelerator pump rod to the throttle lever.
  8.  
  9. Install the vacuum hose between the depression chamber and the throttle body.
  10.  
  11. Install the throttle return spring and the damper spring.
  12.  
  13. Connect the ground wire for the fuel cut-off solenoid.
  14.  
  15. Install new screws to hold the choke cover in place.
  16.  
  17. Install the coolant hose from the throttle body to the wax element.
  18.  
  19. Move the carburetor linkage by hand, checking that motions are smooth and there is no binding in any of the mechanisms.
  20.  
  21. Reinstall the carburetor.
  22.  

Feedback Models

See Figures 6 through 39


WARNING
Certain parts or assemblies must not be disassembled or altered during overhaul. The choke plate and shaft, automatic choke linkage, inner venturi, throttle plate and shaft, and fuel inlet nipple must be left alone. Damage and or reduced performance may result from tampering with these components. Many of the screws have Phillips-type heads. Use a screwdriver which fits the head exactly. An improper tool can damage the head of the screw and cause problems during reassembly.

  1. Remove the carburetor from the vehicle, following the instructions earlier in this section. Drain any remaining fuel into a container with an airtight lid. Place the carburetor on the workbench in a clean, dry area. Placing it on a large, lint-free cloth will help prevent parts from getting lost or rolling around.
  2.  
  3. Remove the throttle return spring and the damper spring.
  4.  
  5. Remove the throttle opener (automatic transmission) or the dashpot (manual transmission) rod from the free lever and remove the opener or dashpot unit from the top of the carburetor.
  6.  
  7. If equipped with automatic transmission, remove the Idle Speed Control (ISC) servo by removing the bracket screws. Put the ISC servo out of the way until reassembly.
  8.  


WARNING
Do not attempt to test the servo with battery voltage. It runs on a lower voltage sent from the ECM. Applying battery voltage to this unit will destroy it.

  1. Remove the connector bracket.
  2.  
  3. Remove the vacuum hose running from the base to the choke breaker. This vacuum line will have a delay valve in it.
  4.  



Click image to see an enlarged view

Fig. Fig. 6: Air cleaner components, emission hoses and feedback carburetor removal components-2.6L engines



Click image to see an enlarged view

Fig. Fig. 7: Components removed when separating the float chamber from the mixing body of a feedback carburetor-2.6L engines



Click image to see an enlarged view

Fig. Fig. 8: Feedback carburetor float chamber disassembly components-2.6L engines



Click image to see an enlarged view

Fig. Fig. 9: Feedback carburetor mixing body and throttle body disassembly components-2.6L engines



Click image to see an enlarged view

Fig. Fig. 10: Remove the water hose and the return and damper springs-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 11: Remove the choke cover-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 12: Remove the Throttle Position Sensor (TPS) from the feedback carburetor

  1. Remove the five screws holding the top of the carburetor to the body and base.
  2.  
  3. The top of the carburetor will be firmly held to the mixing body by the gasket. Do not attempt to lift the top by hand. Use a screwdriver blade or similar thin, flat tool inserted between the top and the enrichment cover. Lightly pry the top upwards and lift the top slowly. Do not apply excessive force and don't try to rush the job.
  4.  
  5. Remove the float pivot pin and remove the float. Carefully remove the needle valve.
  6.  


WARNING
Do not let the float drop and do not apply any force to the float. The needle valve controlled by the float will be damaged.

  1. The valve seat may be removed by using two small, flat-bladed screwdrivers to gently lever the seat upwards and out of position. Use care not to damage the surrounding area or the seat mounts during this process.
  2.  
  3. Find the electrical connector for the Feedback Solenoid Valve (FBSV). The terminals must be removed from the connector housing before the valve can be removed. Use a very thin, flat tool (such as a jeweler's screwdriver) inserted into the connector to loosen the stopper and remove each terminal.
  4.  
  5. Remove the grommet from the top of the carburetor. Remove the retainer and remove the FBSV attaching screw; remove the feedback solenoid valve.
  6.  



Click image to see an enlarged view

Fig. Fig. 13: Remove the throttle opener/dashpot, being careful not to bend the actuating rods



Click image to see an enlarged view

Fig. Fig. 14: Removing the terminals from the connector body. Use a very small prytool to gently lift the stop tab within the plastic shell



Click image to see an enlarged view

Fig. Fig. 15: Remove the feedback solenoid valve after the terminals are free



Click image to see an enlarged view

Fig. Fig. 16: Removing the solenoid valve-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 17: Removing the bowl vent solenoid-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 18: Removing the Bowl Vent Valve (BVV)-feedback carburetor

  1. Remove the retainer and remove the Slow Cut Solenoid Valve (SCSV) from the carburetor top. Hold the solenoid by the body and avoid pulling on the wiring.
  2.  
  3. Using the same small screwdriver technique as in Step 11, disconnect the SCSV terminals from the plastic connector body and remove the SCSV from the carburetor.
  4.  
  5. Use a hand grinder or similar tool to remove the heads of the rivets holding the cover of the choke assembly. Remove the small screw in the bottom of the cover.
  6.  
  7. Remove the packing (gasket), bimetal assembly and plate.
  8.  
  9. Using a pin punch or similar tool, remove the remainder of the rivets from each hole. Take care not to damage the surrounding material.
  10.  
  11. Remove the bimetal terminal from the wiring connector.
  12.  
  13. Remove the bowl vent valve.
  14.  

There are small springs within this unit. Take note of their location and placement, and be careful not to lose them.

  1. Remove the choke breaker cover.
  2.  



Click image to see an enlarged view

Fig. Fig. 19: Removing the choke breaker cover-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 20: Removing the depression chamber-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 21: Removing the accelerator pump rod-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 22: Remove the snapring and then the choke rod-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 23: Remove the float chamber cover-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 24: Remove the pin, then remove the float and needle-feedback carburetor

  1. Remove the check weight and its ball and remove the steel ball from the anti-overfill device.
  2.  
  3. Remove the accelerator pump rod from the throttle shaft lever.
  4.  
  5. Remove the screw from the throttle body assembly, taking care not to raise burrs on the head of the screw. Any deformation will prevent the base from mating to the manifold properly.
  6.  
  7. Using a screwdriver which exactly matches the groove, remove the main jets.
  8.  
  9. Remove the accelerator pump mounting screws and remove the pump cover link assembly, the diaphragm, spring, pump body and gasket from the carburetor body.
  10.  
  11. Remove the three attaching screws from the enrichment valve and remove the cover, spring, and diaphragm assembly from the main body of the carburetor.
  12.  
  13. Remove the vacuum hose running between the depression chamber and the throttle body.
  14.  
  15. Disconnect the depression chamber rod from the secondary throttle lever. Unbolt and remove the depression chamber.
  16.  
  17. Using a screwdriver that exactly matches the screw heads, remove the throttle position sensor from the throttle body (base) of the carburetor.
  18.  
  19. Wearing eye protection and gloves, carefully clean the fuel and air passages with a spray cleaner and, if available, compressed air. A majority of carburetor problems are caused by very small bits of dirt lodging in the air or fuel passages. Do NOT use metal wire or similar to clean the passages.
  20.  



Click image to see an enlarged view

Fig. Fig. 25: Use a pair of pliers to remove the needle seat-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 26: When removing the needle seat, grasp it by area A, not area B-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 27: Remove the main jet with a screwdriver equipped with the proper-sized blade for the main jet slot-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 28: Remove the pilot jet retainer and pull the secondary jet out with pliers-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 29: Remove the two lockscrews, then remove the choke pinion assembly-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 30: Remove the check weight and ball, as well as the steel ball of the anti-overfill device-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 31: Remove the accelerator pump mounting screws, then remove the pump cover link assembly, diaphragm, spring, body and gasket from the main body-feedback carburetor

  1. Check the diaphragms carefully for any sign of damage or cracking.
  2.  
  3. Check the operation of the needle valve; it should move lightly and smoothly. If any binding is felt, replace it.
  4.  
  5. Check the fuel inlet filter (above the needle valve) for clogging.
  6.  
  7. Check the float for cracks, deformation or internal leakage.
  8.  
  9. Inspect the motion of the various linkages and pivots. If any binding is felt, clean the system thoroughly and apply a light coat of lubricant.
  10.  
  11. Check the operation of both solenoid valves. Apply battery voltage to the terminals; the solenoid should operate with a distinct click each time power is applied or removed. Inspect the tip of the FBSV to insure the jet is open and clean.
  12.  
  13. Use an ohmmeter to check the solenoids' resistance. The SCSV should have a resistance of 48-60 ohms at 68°F (20°C); the FBSV should have 54-66 ohms resistance at the same temperature.
  14.  

Resistance will increase or decrease as the temperature rises or falls. Make common sense allowances for the temperature in which you are testing the units.

  1. Hold one lead of the ohmmeter against the case of each solenoid and touch the other lead to each terminal. There should NOT be continuity between the case and the terminals.
  2.  



Click image to see an enlarged view

Fig. Fig. 32: After removing the snapring from the sub-EGR control valve pin, remove the pin and the link from the valve. Take the little steel ball and spring out of the sub-EGR control valve-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 33: Inspect the function of the dashpot and depression chamber-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 34: Sizes are marked on each jet; exact replacements must be used-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 35: Use a hand riveter to refasten the bimetal choke cover back onto the choke body-feedback carburetor

  1. Use the ohmmeter to check the bimetal assembly. Connect one lead to the wire terminal and the other lead to the body of the assembly. Correct resistance is approximately 6 ohms at 68°F (20°C).
  2.  
  3. The dashpot should be inspected by pulling outward on the rod. Resistance should be felt; when released, the lever should return quickly to its original position.
  4.  
  5. The depression chamber is checked by pushing the rod all the way into the unit and then blocking the vacuum port firmly with a finger. Release the rod; if it stays in place (with the vacuum port blocked), the unit is good. If the rod returns to its original extended position, the diaphragm inside has failed.
  6.  
  7. Before reassembly, make certain that all parts are clean and dry. Any gasket or O-ring which was removed MUST be replaced with a new one during reinstallation.
  8.  

If the jets are to be replaced, the new ones must be exact replacements. The jets have a number stamped on them for identification. Jet size is selected based on sophisticated air flow measurements during assembly of the carburetor; changing the jets will lead to extreme driveability and emission problems.

To assemble:
  1. Install the throttle position sensor onto the throttle body and tighten the screws without causing damage.
  2.  
  3. Install the depression chamber. Connect the chamber rod to the secondary throttle lever.
  4.  
  5. Install the vacuum hose from the depression chamber to the throttle body.
  6.  
  7. Assemble the diaphragm, spring and cover for the enrichment valve. Install the valve and cover assembly onto the main body.
  8.  



Click image to see an enlarged view

Fig. Fig. 36: The terminals must be correctly installed in the connector body-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 37: The throttle plate clearance must be checked after the high idle cam is correctly set-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 38: Use a drill or feeler gauge to check the throttle plate clearance-feedback carburetor



Click image to see an enlarged view

Fig. Fig. 39: Check the choke plate clearance with the throttle wide open; make needed adjustments by carefully bending the lever-feedback carburetor

  1. Assemble the accelerator pump and install it to the body with a new gasket.
  2.  
  3. Install the main jets without damaging them.
  4.  
  5. Install the screw into the throttle body assembly without damaging the head of the screw.
  6.  
  7. Install the accelerator pump rod to the throttle shaft lever.
  8.  
  9. Install the check weight and ball and the steel ball for the anti-overfill device.
  10.  
  11. Install the choke breaker cover.
  12.  
  13. Install the bowl vent valve, taking care to assemble the small springs and diaphragm correctly.
  14.  
  15. Loosely hold the bimetal choke assembly in place. Route the terminal and wiring correctly to the plastic connector. Install the terminal in the connector by pushing it into the correct location. The stopper pin will engage the terminal automatically. A slight click may be heard or felt when the terminal is in position.
  16.  
  17. To install the bimetal assembly:
    1. Using a new gasket, place the cup on the top of the spiral spring in line with the choke lever. Fit the cap into place and use the small screw to hold it in place.
    2.  
    3. Line up the mating marks on the case and body.
    4.  
    5. Once aligned, install the rivets to hold the case in place. A hand riveter is required; the use of nuts and bolts is NOT recommended.
    6.  

  18.  
  19. Route the wiring for the FBSV and SCSV correctly. Install terminals into the correct connector port by pushing them in firmly.
  20.  
  21. Install the SCSV and its retainer into the top of the carburetor. Handle the unit only by the body and avoid pulling on the wire.
  22.  
  23. Install the FBSV into the carburetor. Install the retainer and attaching screw as well as a new grommet.
  24.  
  25. Install the seat and needle valve, making sure each is correctly placed and securely installed.
  26.  
  27. Install the float and pivot pin, taking great care not to put any undue force on the float. Refer to the carburetor adjustment section for float level adjustment procedure.
  28.  
  29. Install the carburetor top to the main body (with a new gasket) and install the five screws. Make sure each screw is tight without deforming the head.
  30.  
  31. Install the vacuum hose and delay valve running from the base of the carburetor to the choke breaker.
  32.  
  33. Install the connector bracket.
  34.  
  35. Install the ISC servo if it was removed (automatic transmission only).
  36.  
  37. Install either the dashpot or throttle opener unit and connect the rod to the free lever.
  38.  
  39. Install the throttle return spring and damper spring.
  40.  
  41. Move the carburetor linkages by hand, checking that motions are smooth and there is no binding in any of the mechanisms.
  42.  
  43. With the carburetor correctly assembled, some adjustments must be made on the bench. Set the high idle cam to the second highest position and turn the carburetor upside down. Using a drill bit of known diameter or a clearance tool, check the clearance between the primary throttle plate and the throttle bore. Correct clearances are:

    2.0L engine with manual transmission: 0.025 in. (0.63mm)
     
    2.0L engine with automatic transmission: 0.028 in. (0.71mm)
     
    2.6L engine with manual transmission: 0.028 in. (0.71mm)
     
    2.6L engine with automatic transmission: 0.031 in. (0.80mm)
     

  44.  

  1. Check the choke unloader clearance by using your finger to lightly press and set the choke plate. When it is fully closed, move the throttle linkage to open the throttle plate(s) all the way; the throttle plates should be vertical in their bores. Measure the clearance between the choke plate and the choke bore. Correct clearance is 0.079 in. (2mm) for Pick-ups and Monteros. If adjustment is needed, gently bend the throttle lever to achieve the correct clearance. Bending the lever upwards increases the clearance and bending it downward reduces the clearance.
  2.  

Generally, the choke unloader clearance should not change after an overhaul. Adjusting this clearance greatly affects cold driveability; check the clearance after an overhaul, but don't adjust it unless necessary.

  1. Install a new base gasket and reinstall the carburetor on the engine, following instructions given previously in this section.
  2.  

 
label.common.footer.alt.autozoneLogo