Montana, Silhouette, Venture 2000-2005

Parking Brake Shoes

Print

Adjustment



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Apply and fully release the parking brake six times.
  4.  
  5. Verify that the parking brake pedal releases completely.
    1. Turn ON the ignition. Verify that the BRAKE indicator lamp is off.
    2.  
    3. If the BRAKE indicator lamp is on, ensure that the parking brake pedal is in release mode and fully returned to stop.
    4.  
    5. Remove the slack in the front parking brake cable by pulling downward on the cable.
    6.  

  6.  
  7. Raise and suitably support the vehicle.
  8.  
  9. Remove the rear wheels and tires.
  10.  
  11. Relieve tension on the park brake system at the park brake equalizer.
  12.  
  13. Remove both rear caliper bracket bolts.
    WARNING
    Support the brake caliper with heavy mechanic's wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  14.  
  15. Remove brake caliper and bracket as one assembly. Do not disconnect the brake hose from the caliper.
  16.  
  17. Support the assembly with mechanic's wire, or equivalent.
  18.  
  19. Remove rear brake rotor.
  20.  
  21. Set the J 21177-A inside of the park brake drum at the widest point. Tighten the set screw on the tool to ensure the proper measurement when removing the tool from the drum.

    Click image to see an enlarged view

    Fig. Measuring the inside of the parking brake drum

  22.  
  23. Position the J 21177-A over the park brake shoe at the widest point.
  24.  
  25. Turn the adjuster on the actuator until the park brake shoe just contacts the J 21177-A.

    Click image to see an enlarged view

    Fig. Measuring the parking brake shoes

  26.  
  27. Repeat these steps for the opposite side.
  28.  
  29. Install both rear brake rotors.
  30.  
  31. Install both rear brake calipers and brackets.
    NOTE
    To ensure that the proper clamp load will be present when installed. It is imperative that the threads on the caliper bracket bolts, as well as the mounting holes in the knuckle, be cleaned of all debris and inspected before proceeding with installation.

  32.  
  33. Clean and visually inspect threads of the caliper bracket bolts and mounting holes in the knuckle.
  34.  
  35. Apply THREADLOCKER, GM P/N 12345493 (Canadian P/N 10953488), or equivalent to the threads of the brake caliper bracket bolts.
    WARNING
    Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  36.  
  37. Install the caliper bracket bolts. Tighten the brake caliper bracket bolts to 130 Nm (96 ft. lbs.).
  38.  
  39. Install the rear wheels and tires.
  40.  
  41. Adjust the parking brake cable by turning the nut at the equalizer while spinning both rear wheels. When either rear wheel starts to drag, back off the nut one full turn.
  42.  
  43. Lower the vehicle to curb height.
  44.  
  45. Apply the parking brake, then inspect for rotation of the rear wheels. If the rear wheels rotate during this inspection, readjust the parking brake cable.
  46.  
  47. Release the parking brake. Verify that the wheels rotate freely.
  48.  
  49. Lower the vehicle.
  50.  

Removal & Installation



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Raise and support the vehicle.
  4.  
  5. Remove the rear tire and wheel assemblies.
  6.  
  7. Relieve the park brake system tension at the equalizer assembly.
  8.  
  9. Remove the rear caliper bracket.
  10.  
  11. Remove the rear rotor.
  12.  
  13. Disconnect and remove the rear park brake cable from the bracket at the rear wheel.
  14.  
  15. Disconnect the park brake cable return spring from the park brake actuator and bracket at the rear wheel.
  16.  
  17. Remove the rear hub. The rear hub, backing plate, park brake cable bracket, and park brake actuator will be removed as an assembly.
  18.  
  19. Remove the 2 retainers and the park brake cable bracket from the park brake actuator. Position the rear hub aside.
  20.  
  21. Remove the park brake shoe and actuator from the backing plate.
  22.  
  23. Separate the park brake shoe from the actuator.

    Click image to see an enlarged view

    Fig. Parking brake cable attachment-rear disc brakes



    Click image to see an enlarged view

    Fig. Parking brake shoes and related parts-rear disc brakes

  24.  

To install:

  1. Assemble the park brake shoe to the actuator.
  2.  
  3. Install the park brake shoe and actuator onto the backing plate.
  4.  
  5. Position the park brake shoe, actuator, and backing plate over the rear hub.
  6.  
  7. Install the park brake cable bracket and the two retainers.
  8.  
  9. Install the rear hub. The rear hub, backing plate, park brake cable bracket, and park brake actuator will be installed as an assembly.
  10.  
  11. Connect the rear park brake cable to the bracket at the rear wheel.
  12.  
  13. Connect the park brake cable return spring to the park brake actuator and bracket at the rear wheel.
  14.  
  15. Install the rear rotor.
  16.  
  17. Install the rear caliper bracket.
  18.  
  19. Install the rear tire and wheel assemblies.
  20.  
  21. Adjust the park brake system.
  22.  
  23. Lower the vehicle.
  24.  

 
label.common.footer.alt.autozoneLogo