MonteCarlo 2000

3.4L V6 VIN E Auto 1

Print

3.4L V6 VIN E Auto

Trouble Code: P0101



MAF Sensor Signal Range/Performance

Possible Causes:



Base engine vacuum leak, PCV valve leaking or stuck open
 
Engine oil dipstick missing or not fully seated
 
MAF sensor signal or ground circuit fault or sensor has failed
 
PCM has failed
 

Trouble Code: P0102



MAF Sensor Circuit Low Frequency

Possible Causes:



MAF sensor element hot wire contaminated or the sensor failed
 
MAF sensor signal shorted to ground or ground circuit problem
 
MAF sensor wiring routed close to the ignition wires, generator, solenoids or electric motors
 
PCM has failed
 

Trouble Code: P0103



Mass Air Flow (MAF) Sensor Circuit High Frequency

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0107



Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0108



Manifold Absolute Pressure (MAP) Sensor Circuit High Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0112



Intake Air Temperature (IAT) Sensor Circuit Low Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0113



Intake Air Temperature (IAT) Sensor Circuit High Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0117



Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0118



Engine Coolant Temperature (ECT) Sensor Circuit High Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0121



Throttle Position (TP) Sensor Performance

Possible Causes:

Inspect for the following conditions:



A stuck or skewed MAP signal or a faulty MAP sensor.
 
A skewed MAP signal may cause the PCM to incorrectly determine the TP sensor is out of range. Test for an unusually low or high MAP reading. This condition can cause DTC P0121 to set. Refer to Manifold Absolute Pressure (MAP) Sensor Circuit Diagnosis
 



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0122



Throttle Position (TP) Sensor Circuit Low Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0123



Throttle Position (TP) Sensor Circuit High Voltage

Possible Causes:

Inspect for the following conditions: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0125



Engine Coolant Temperature (ECT) Insufficient for Closed Loop Fuel Control

Possible Causes:

DTC P0125 set indicates a skewed ECT sensor. Comparing the engine coolant temperature displayed on a scan tool with the actual coolant temperature measured with a thermometer may isolate this condition. If the displayed engine coolant temperature is not close to the actual coolant temperature, replace the ECT sensor. Refer to Engine Coolant Temperature (ECT) Sensor Replacement . Inspect for: Many situations may lead to an intermittent condition. Perform each inspection or test as directed. Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0131



HO2S-11 (Bank 1 Sensor 1) Circuit Low Input

Possible Causes:



Air leaks in the exhaust system, intake manifold, vacuum lines
 
Engine misfire condition present (look for P0300 series codes)
 
Fuel system too lean (possible low fuel pressure, water in fuel)
 
HO2S signal circuit is shorted to the sensor or chassis ground
 
HO2S is damaged (i.e., cracked) or air reference hole clogged
 
PCM has failed
 

Trouble Code: P0132



HO2S-11 (Bank 1 Sensor 1) Circuit High Input

Possible Causes:



Fuel system is too rich (fuel pressure too high, fuel pressure regulator leaking, or one or more fuel injectors sticking/leaking)
 
HO2S element is silicon, water or fuel contaminated
 
HO2S signal tracking (water intrusion) in the connector causing a short between the HO2S signal and heater power circuits
 
PCM has failed
 

Trouble Code: P0133



HO2S-11 (Bank 1 Sensor 1) Slow Response

Possible Causes:



Exhaust leak present in the exhaust manifold or exhaust pipes
 
Fuel system is too rich (fuel pressure too high, fuel pressure regulator leaking, or one or more fuel injectors sticking/leaking)
 
HO2S element is silicon, water or fuel contaminated or it failed
 
TP sensor element broken (can cause false acceleration event)
 
PCM has failed
 

Trouble Code: P0134



HO2S-11 (Bank 1 Sensor 1) Insufficient Activity

Possible Causes:



HO2S heater is damaged or has failed
 
HO2S signal or ground circuit has a high resistance condition
 
HO2S signal circuit is open or shorted to system power (B+)
 
HO2S has failed (i.e., it is silicon, water or fuel contaminated)
 
PCM has failed
 

Trouble Code: P0135



HO2S-11 (Bank 1 Sensor 1) Heater Circuit Malfunction

Possible Causes:



HO2S heater ground circuit is open or has high resistance
 
HO2S heater power circuit is open (test O2S fuse in fuse block)
 
HO2S heater element is damaged or has failed
 
PCM has failed
 

Trouble Code: P0137



HO2S-12 (Bank 1 Sensor 2) Circuit Low Input

Possible Causes:



Air leaks in the exhaust system, intake manifold, vacuum lines
 
Engine misfire condition present (look for P0300 series codes)
 
Fuel system too lean (possible low fuel pressure, water in fuel)
 
HO2S signal circuit is shorted to the sensor or chassis ground
 
HO2S is damaged (i.e., cracked) or air reference hole clogged
 
PCM has failed
 

Trouble Code: P0138



HO2S-12 (Bank 1 Sensor 2) Circuit High Input

Possible Causes:



Fuel system is too rich (fuel pressure too high, fuel pressure regulator leaking, or one or more fuel injectors sticking/leaking)
 
HO2S element is silicon, water or fuel contaminated
 
HO2S signal tracking (water intrusion) in the connector causing a short between the HO2S signal and heater power circuits
 
PCM has failed
 

Trouble Code: P0140



HO2S-12 (Bank 1 Sensor 2) Insufficient Activity

Possible Causes:



Exhaust leak present in the exhaust manifold or exhaust pipes
 
HO2S signal or ground circuit has a high resistance condition
 
HO2S element is silicon, water or fuel contaminated
 
PCM has failed
 

Trouble Code: P0141



HO2S-12 (Bank 1 Sensor 2) Heater Circuit Malfunction

Possible Causes:



HO2S heater ground circuit is open or has high resistance
 
HO2S heater power circuit is open (test O2 fuse in fuse block)
 
HO2S heater element is damaged or has failed
 
PCM has failed
 

Trouble Code: P0171



Fuel Trim System Lean (Bank 1)

Possible Causes:



Air leaks in intake manifold, exhaust pipes or exhaust manifold
 
Fuel control sensor is out of calibration (ECT, IAT or MAF)
 
Low fuel pressure (fuel filter clogged, pressure regulator failure)
 
One or more injectors restricted or pressure regulator has failed
 
HO2S element is contaminated, deteriorated or has failed
 
Vacuum hose is disconnected, broken, leaking or loose
 

Trouble Code: P0172



Fuel Trim System Rich (Bank 1)

Possible Causes:



Base engine "mechanical" fault affecting one or more cylinders
 
Excess fuel vapors in crankcase (the oil needs to be changed)
 
EVAP system component has failed or canister fuel saturated
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAF)
 
Fuel delivery system supplying too much fuel during cruise or idle periods (e.g., faulty fuel pump, or faulty pressure regulator)
 
Fuel injector(s) is leaking or stuck partially open (one or more)
 
HO2S is contaminated, deteriorated or it has failed
 

Trouble Code: P0201



Fuel Injector 1 Control Circuit Malfunction

Possible Causes:



Injector 1 control circuit is open between injector and PCM
 
Injector 1 control circuit is grounded between injector and PCM
 
Injector 1 power circuit is open (test INJ fuse in fuse block)
 
Injector 1 is damaged or it has failed
 
PCM is damaged
 

Trouble Code: P0202



Fuel Injector 2 Control Circuit Malfunction

Possible Causes:



Injector 2 control circuit is open between injector and PCM
 
Injector 2 control circuit is grounded between injector and PCM
 
Injector 2 power circuit is open (test INJ fuse in fuse block)
 
Injector 2 is damaged or it has failed
 
PCM is damaged
 

Trouble Code: P0203



Fuel Injector 3 Control Circuit Malfunction

Possible Causes:



Injector 3 control circuit is open between injector and PCM
 
Injector 3 control circuit is grounded between injector and PCM
 
Injector 3 power circuit is open (test INJ fuse in fuse block)
 
Injector 3 is damaged or it has failed
 
PCM is damaged
 

Trouble Code: P0204



Fuel Injector 4 Control Circuit Malfunction

Possible Causes:



Injector 4 control circuit is open between injector and PCM
 
Injector 4 control circuit is grounded between injector and PCM
 
Injector 4 power circuit is open (test INJ fuse in fuse block)
 
Injector 4 is damaged or it has failed
 
PCM is damaged
 

Trouble Code: P0205



Fuel Injector 5 Control Circuit Malfunction

Possible Causes:



Injector 5 control circuit is open between injector and PCM
 
Injector 5 control circuit is grounded between injector and PCM
 
Injector 5 power circuit is open (test INJ fuse in fuse block)
 
Injector 5 is damaged or it has failed
 
PCM is damaged
 

Trouble Code: P0206



Fuel Injector 6 Control Circuit Malfunction

Possible Causes:



Injector 6 control circuit is open between injector and PCM
 
Injector 6 control circuit is grounded between injector and PCM
 
Injector 6 power circuit is open (test INJ fuse in fuse block)
 
Injector 6 is damaged or it has failed
 
PCM is damaged
 

Trouble Code: P0218



Transmission Fluid Overtemperature

Possible Causes:



Inspect the transmission cooling system for possible blockage and restrictions.
 
Ask the customer about possible overloading, exceeding the trailer towing limit, or towing in overdrive.
 

Trouble Code: P0230



Fuel Pump Control Circuit Malfunction

Possible Causes:



Fuel pump relay power circuit is open (test B+ from fuse box)
 
Fuel pump control circuit is open or shorted to ground
 
Fuel pump control circuit is shorted to system power
 
PCM has failed
 
TSB 00-06-04-023 contains a repair procedure for this code
 

Trouble Code: P0300



Multiple Engine Misfire Detected

Possible Causes:



Base engine mechanical fault that affects one or more cylinders
 
Fuel metering fault (high fuel pressure or fuel contaminated)
 
EVAP system problem or the EVAP canister is fuel saturated
 
EGR valve is stuck open or the PCV system has a vacuum leak
 
Ignition system fault (a coil) that affects more than one cylinder
 
MAF sensor contamination (it can cause a very lean condition)
 
TSB 99-06-04-005B contains a repair procedure for this code
 
TSB 03-06-04-030 contains a repair procedure for this code
 

Trouble Code: P0300



Multiple Cylinder Misfire Detected

Possible Causes:



Base engine mechanical fault that affects one or more cylinders
 
Fuel metering fault that affects more than one cylinder
 
Fuel pressure too low or too high, fuel supply contaminated
 
EVAP system problem or the EVAP canister is fuel saturated
 
EGR valve is stuck open or the PCV system has a vacuum leak
 
IC control circuit is shorted to ground (an intermittent fault)
 
Ignition system fault (a coil) that affects more than one cylinder
 
MAF sensor contamination (it can cause a very lean condition)
 
TSB 77-65-30 contains a repair procedure for this code
 
TSB 03-06-04-030 contains a repair procedure for this code
 

Trouble Code: P0325



Knock Sensor Circuit Malfunction (Bank 1)

Possible Causes:



Knock sensor signal circuit is open, shorted to ground or power
 
Knock sensor ground circuit is open (i.e., not mounted properly)
 
Knock sensor is damaged or has failed
 
On modules with an integrated sensor, clear the codes and retest for codes. If the same code resets, the PCM has failed.
 

Trouble Code: P0327



Knock Sensor Circuit Malfunction

Possible Causes:



Knock sensor signal circuit is open, shorted to ground or power
 
Knock sensor ground circuit is open (check for proper torque)
 
Knock sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0336



Crankshaft Reference 24X Circuit Malfunction

Possible Causes:



CKP sensor signal circuit is open or shorted to ground
 
CKP sensor ground (Low Reference) circuit is open
 
CKP sensor is damaged or it failed (check crankshaft reluctor)
 
PCM has failed
 

Trouble Code: P0341



Camshaft Position (CMP) Sensor Performance

Possible Causes:

DTC P0341 can be caused by secondary components leaking high voltage into the ignition module. Check for:



Incorrect harness routing near the secondary ignition components
 
An ignition coil that is arcing to the wiring harness or to the IC module--Check the ignition coils for cracks, carbon tracking, or other signs of damage.
 
Secondary ignition wires that are arcing to the wiring harness
 



Loose terminal connection

Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 
Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
 

Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
 

Trouble Code: P0401



Insufficient EGR Flow Detected

Possible Causes:



Base engine problem (e.g., a severely restricted exhaust), or any other problem that causes the engine to run poorly
 
EGR passages or intake passages clogged or restricted
 
EGR pipe is clogged, dirty or otherwise restricted
 
EGR vacuum hoses damaged, loose or routed incorrectly
 
EGR solenoid valve is clogged (carbon), damaged or has failed
 
MAP sensor is dirty, damaged or it is "skewed"
 

Trouble Code: P0403



EGR Solenoid Control Circuit Malfunction

Possible Causes:



EGR solenoid control circuit is open, shorted to ground or B+
 
EGR solenoid high control (VREF) circuit is open
 
EGR solenoid is damaged or has failed
 
PCM has failed
 
TSB 02-06-04-053 contains a repair procedure for this code
 

 
label.common.footer.alt.autozoneLogo