MonteCarlo 2000

3.4L V6 VIN E Auto 4

Print

Trouble Code: P1626



Theft Deterrent System Fuel Enable Circuit Malfunction

Possible Causes:



Perform the Onboard Diagnostic System Check
 
If the PCM needs replacing, it must be reprogrammed
 
TSB 02-08-56-002 contains a repair procedure for this code
 

Trouble Code: P1629



Theft Deterrent Signal Not Present, Engine Cranking

Possible Causes:



Perform the Onboard Diagnostic System Check
 
Refer to the diagnostics for the Theft Deterrent System
 
If the PCM needs replacing, it must be reprogrammed
 
TSB 02-08-56-002 contains a repair procedure for this code
 

Trouble Code: P1630



Theft Deterrent Learn Mode Active

Possible Causes:



Perform the Onboard Diagnostic System Check
 
Refer to the diagnostics for the Theft Deterrent System
 
If the PCM needs replacing, it must be reprogrammed
 

Trouble Code: P1631



Theft Deterrent Enable Signal Not Correct

Possible Causes:



This code indicates that the VTD password that the PCM has learned does not agree with the password being received from the theft deterrent system. This condition can occur if an incorrect key is being used when attempting to start the vehicle or if the Theft Deterrent Module has been replaced and the PCM password learn function has not been enabled.
 
Refer to Programming the Theft Deterrent System
 
Perform the Powertrain Onboard Diagnostic System Check
 

Trouble Code: P1635



5-Volt Reference 'A' Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to sensor ground or chassis ground
 
5v VREF circuit, MAP or FTP sensor circuit is shorted to (B+)
 
5v VREF circuit shorted to EGR sensor High signal circuit
 
EGR solenoid valve (and sensor) is damaged or has failed
 
PCM has failed
 

Trouble Code: P1639



5-Volt Reference 'B' Circuit Malfunction

Possible Causes:



A/C refrigerant pressure sensor VREF circuit is open, shorted to ground or shorted to system power
 
A/C refrigerant pressure sensor is damaged or PCM has failed
 
TSB 61-65-61 contains a repair procedure for this code
 

Trouble Code: P1811



Maximum Adapt and Long Shift

Possible Causes:



Ask the customer about possible overloading, exceeding the trailer towing limit, or towing in overdrive.
 
Ensure that the PCM has the latest calibration update.
 

Trouble Code: P1819



Internal Mode Switch - No Start/Wrong Range (3.8L Monte Carlo)

Possible Causes:



Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 
Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems.
 
Refer to the Transmission Internal Mode Switch Logic table for the normal range signals and the invalid combinations.
 

Trouble Code: P1826



Internal Mode Switch Circuit C High (3.8L Monte Carlo)

Possible Causes:



Inspect the connectors at the controller, the component and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 
Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems.
 

Trouble Code: U1000



Class 2 Communication Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
SDM (module) could be shorted pulling the voltage low
 

Trouble Code: U1016



No Communication With Powertrain Control Module

Possible Causes:



PCM Class 2 circuit is open, shorted to ground or to B+
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
PCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1048



No Communication With Rear Wheel Steering Control Module

Possible Causes:



RWSCM Class 2 circuit is open, shorted to ground or to B+
 
RWSCM ignition power circuit has a high resistance condition
 
RESCM main ground circuit(s) has a high resistance condition
 
RESCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1064



No Communication With Body Control Module

Possible Causes:



BCM Class 2 circuit is open, shorted to ground or to B+
 
BCM ignition power circuit has a high resistance condition
 
BCM main ground circuit(s) has a high resistance condition
 
BCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1088



No Communication With SDM (Restraint Module)

Possible Causes:



SDM Class 2 circuit is open, shorted to ground or to B+
 
SDM ignition power circuit has a high resistance condition
 
SDM main ground circuit(s) has a high resistance condition
 
SDM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1096



No Communication With Instrument Panel Cluster

Possible Causes:



IPC Class 2 circuit is open, shorted to ground or to B+
 
IPC ignition power circuit has a high resistance condition
 
IPC main ground circuit(s) has a high resistance condition
 
IPC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1097



No Communication With Driver Information Center

Possible Causes:



DIC Class 2 circuit is open, shorted to ground or to B+
 
DIC ignition power circuit has a high resistance condition
 
DIC main ground circuit(s) has a high resistance condition
 
DIC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1151



No Communication With Vehicle Interface Unit

Possible Causes:



VIU Class 2 circuit is open, shorted to ground or to B+
 
VIU ignition power circuit has a high resistance condition
 
VIU main ground circuit(s) has a high resistance condition
 
VIU (module) may have failed and is pulling the circuit low
 

Trouble Code: U1152



No Communication With HVAC Control Module

Possible Causes:



HVAC Class 2 circuit is open, shorted to ground or to B+
 
HVAC ignition power circuit has a high resistance condition
 
HVAC main ground circuit(s) has a high resistance condition
 
HVAC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1255



Class 2 Communications Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 

Trouble Code: U1300



Class 2 Data Link Low

Possible Causes:



This DTC cannot be retrieved with a current status. The diagnosis of U1300 is accomplished via the symptom, Scan Tool Does Not Communicate with a Class 2 Device. Refer to Scan Tool Does Not Communicate with Class 2 Device .
 
An intermittent condition is likely to be caused by a short to ground on the class 2 serial data circuit. Use the Scan Tool Does Not Communicate with a Class 2 Device procedure in order to isolate an intermittent condition. Refer to Scan Tool Does Not Communicate with Class 2 Device .
 

Trouble Code: U1301



Class 2 Data Link High

Possible Causes:



This DTC cannot be retrieved with a current status. The diagnosis of U1301 is accomplished via the symptom, Scan Tool Does Not Communicate with a Class 2 Device. Refer to Scan Tool Does Not Communicate with Class 2 Device .
 
An intermittent condition is likely to be caused by a short to voltage on the class 2 serial data circuit. Use the Scan Tool Does Not Communicate with a Class 2 Device procedure in order to isolate an intermittent condition. Refer to Scan Tool Does Not Communicate with Class 2 Device .
 

Trouble Code: U1305



Class 2 Data Link High or Low

Possible Causes:



Class 2 serial data line has either a high or low voltage condition on the circuit, and the module cannot identify the fault
 
One or more modules on Class 2 line has an short to power
 
One or more modules on the Class 2 line has a short to ground
 

Trouble Code: U1XXX



Lost Communication with XXX

 
label.common.footer.alt.autozoneLogo