Nissan Car 350Z & Maxima 1999-06

Exhaust Manifold

Imprimir

Removal & Installation



  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Exhaust manifolds from the exhaust pipes
     
    Protective covers from the manifolds
     
    Heated Oxygen (HO 2 S) sensor from the manifold, if equipped
     
    Exhaust manifold-to-engine mounting nuts
     
    Manifolds from the engine and discard the gaskets
     

  4.  

To install:

  1. Clean all gasket mounting surfaces. Install new gaskets.
  2.  
  3. Install or connect the following:

    Exhaust manifold and torque the nuts in steps to 22-24 ft. lbs. (30-32 Nm)
     
    Protective shields and torque the bolts in steps to 46-57 inch lbs. (5-7 Nm)
     
    Exhaust manifolds to the exhaust pipes and torque the nuts to 32-37 ft. lbs. (43-50 Nm)
     
    HO 2 S sensor to the manifold and torque the fastener to 30-44 ft. lbs. (40-60 Nm), if equipped
     
    Negative battery cable
     

  4.  
  5. Start the engine and check for exhaust leaks.
  6.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Exhaust manifolds from the exhaust pipes
     
    Protective covers from the manifolds
     
    Heated Oxygen Sensor (HO 2 S) from the manifold, if equipped
     
    Exhaust manifold-to-engine mounting nuts
     
    Manifolds from the engine and discard the gaskets
     

  4.  

To install:

  1. Clean all gasket mounting surfaces. Install new gaskets.
  2.  
  3. Install or connect the following:

    Exhaust manifold and torque the nuts in steps to 21-24 ft. lbs. (29-33 Nm)
     
    Protective shields and torque the bolts in steps to 46-57 inch lbs. (5-7 Nm)
     
    Exhaust manifolds to the exhaust pipes and torque the nuts to 32-37 ft. lbs. (43-50 Nm)
     
    HO 2 S sensor to the manifold and torque the fastener to 30-44 ft. lbs. (40-60 Nm), if equipped
     
    Negative battery cable
     

  4.  
  5. Start the engine and check for exhaust leaks.
  6.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Drain the engine coolant
  4.  
  5. Remove or disconnect the following:

    Negative battery cable
     
    Strut tower bar
     
    Engine cover
     
    Air cleaner case and duct
     
    Heated oxygen sensor No. 2 connectors and sensors
     
    Exhaust mounting bracket between transmission and catalytic converters
     
    Catalytic converters
     
    Heated oxygen sensor No. 1 connectors and sensors
     
    Water and heater pipe on both sides Heat shield
     
    Exhaust manifold bolts in reverse of the tightening sequence
     
    Manifold gaskets

    Click image to see an enlarged view

    Fig. Exhaust manifold gasket identification-350Z 3.5L engine



    Click image to see an enlarged view

    Fig. Exhaust manifold bolt tightening sequence-350Z 3.5L engine

     

  6.  

To install:

  1. Clean all gasket mounting surfaces. Install new gaskets noting the correct placement.
  2.  
  3. Installation is the reverse of the removal procedure noting the following:

    Exhaust manifold and torque the nuts in sequence to 22 ft. lbs. (30 Nm)
     
    Heat shields and torque the bolts in steps to 51 inch lbs. (6 Nm)
     
    Exhaust manifolds to the exhaust pipes and torque the nuts to 46 ft. lbs. (63 Nm)
     
    Oxygen sensors and torque the fastener to 33 ft. lbs. (45 Nm)
     

  4.  

1.6L And 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Engine undercovers
     
    Air cleaner or collector assembly
     
    Heat shields from the manifold and front exhaust pipe
     
    Front exhaust pipe from the exhaust manifold
     
    Temperature sensors, Oxygen (O 2 ) sensors and air induction pipes from the manifold
     
    Manifold support brackets
     
    Exhaust manifold attaching nuts and the manifold from the block. Discard the exhaust manifold gaskets.
     

  4.  
  5. Clean the gasket surfaces and check the manifold for cracks and warpage.
  6.  

To install:

  1. Install the exhaust manifold with a new gasket.
  2.  
  3. On SR20DE engines, torque the fasteners from the center outward in several stages to 27-35 ft. lbs. (37-48 Nm).
  4.  
  5. On GA16DE engines, tighten the mounting nuts with washers in sequence to 19-21 ft. lbs. (26-29 Nm).
  6.  
  7. Install or connect the following:

    Temperature sensors, O 2 sensors and air induction pipes
     
    Manifold support brackets
     
    Exhaust pipe to the manifold using a new gasket. Torque the nuts to 21-25 ft. lbs. (28-33 Nm) for GA16DE engine models or 32-37 ft. lbs. (43-50 Nm) for SR20DE engine models
     
    Heat shields
     
    Air cleaner or collector assembly
     
    Engine undercovers
     
    Negative battery cable
     

  8.  
  9. Start the engine and check for exhaust leaks.
  10.  

1.8L And 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Engine undercovers
     
    Air cleaner or collector assembly
     
    Heat shields from the manifold and front exhaust pipe
     
    Front exhaust pipe from the exhaust manifold
     
    Temperature sensors, Oxygen (O2) sensors and air induction pipes from the manifold
     
    Manifold support brackets
     
    Exhaust manifold attaching nuts and the manifold from the block. Discard the exhaust manifold gaskets.
     

  4.  
  5. Clean the gasket surfaces and check the manifold for cracks and warpage.
  6.  

To install:

  1. Install the exhaust manifold with a new gasket.
  2.  
  3. On 1.8L engines, tighten the mounting nuts with washers in sequence to 19-21 ft. lbs. (26-29 Nm).
  4.  
  5. On 2.0L engines, torque the fasteners from the center outward in several stages to 27-35 ft. lbs. (37-48 Nm).
  6.  
  7. Install or connect the following:

    Temperature sensors, O2 sensors and air induction pipes
     
    Manifold support brackets
     
    Exhaust pipe to the manifold using a new gasket. Torque the nuts to 21-25 ft. lbs. (28-33 Nm) for 1.8L engines, or 32-37 ft. lbs. (43-50 Nm) for 2.0L engine models.
     
    Heat shields
     
    Air cleaner or collector assembly
     
    Engine undercovers
     
    Negative battery cable
     

  8.  
  9. Start the engine and check for exhaust leaks.
  10.  

2.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Engine undercover
     
    Air/fuel ratio sensor connector
     
    Oxygen (O2) sensor electrical connector
     
    Air/fuel ratio sensor
     
    Oxygen (O2) sensor
     
    Upper and lower exhaust manifold covers
     
    Exhaust manifold/catalyst assembly in reverse of the tightening sequence
     

  4.  

To install:



Click image to see an enlarged view