Nissan Frontier, Xterra 1998-05

Locks & Lock Systems 2

Print

Power Door Locks



Removal & Installation
Door Lock Motor
1998-2004

NOTE
The manufacturer does not provide removal and installation procedures for this operation. In order to remove the door lock actuator the door panel must first be removed.



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part one)-1998-1999



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part two)-1998-1999



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part three)-1998-1999



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part one)-2000-2004 Frontier



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part two)-2000-2004 Frontier



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part one)-2000-2004 Xterra



Click image to see an enlarged view

Fig. Front and rear door panel and related components (part two)-2000-2004 Xterra

Flat Type
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the inside handle escutcheon.
  6.  
  7. Remove the window regulator handle.
  8.  
  9. Remove the armrest retaining screws.
  10.  
  11. Remove the armrest.
  12.  
  13. Lift out and remove the door panel.
  14.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Formed Type
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the manual window regulator, if equipped.
  6.  
  7. Remove the inside handle escutcheon.
  8.  
  9. Remove the door armrest.
  10.  
  11. Remove the screw securing the door pull handle.
  12.  
  13. Remove the power window switch, then disconnect the electrical connector.
  14.  
  15. Remove the two screws.
  16.  
  17. Remove the clips retaining the door panel.
  18.  
  19. Lift out and remove the door panel.
  20.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

2005

NOTE
The manufacturer does not provide removal and installation procedures for this operation. In order to remove the door lock actuator the door panel must first be removed.

Front Door


Click image to see an enlarged view

Fig. Front door panel and related components-2005 Frontier



Click image to see an enlarged view

Fig. Front door panel and related components-2005 Xterra



Click image to see an enlarged view

Fig. Front door lock assembly and related components-2005

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the power window switch assembly. Disconnect the harness electrical connector.
  6.  
  7. Remove the pull handle escutcheon.
  8.  
  9. Remove the pull handle cover, then remove the door finisher screw.
  10.  
  11. Lift the armrest upward to release the clips. Remove the armrest. Remove the screws behind the armrest.
  12.  
  13. Release the clips and remove the door panel.
  14.  
  15. Disconnect the lock lever cable and the pull handle cable from the lever assembly. Remove the pull handle/lock lever assembly.
  16.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Rear Door (Crew Cab)


Click image to see an enlarged view

Fig. Rear door panel and related components-2005 Crew Cab



Click image to see an enlarged view

Fig.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the power window switch assembly. Disconnect the harness electrical connector.
  6.  
  7. Remove the screw behind the pull handle cover. Remove the pull handle cover.
  8.  
  9. Remove the pull handle escutcheon.
  10.  
  11. Lift the armrest upward to release the clips. Remove the armrest. Remove the screws behind the armrest.
  12.  
  13. Release the clips and remove the door panel.
  14.  
  15. Disconnect the lock lever cable and the pull handle cable from the lever assembly. Remove the pull handle/lock lever assembly.
  16.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Rear Door (King Cab)


Click image to see an enlarged view

Fig. Rear door panel and related components-2005 King Cab



Click image to see an enlarged view

Fig.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Disconnect the harness connector, for the passenger side. Remove the lower seat belt anchor bolt.
  6.  
  7. Release the clips and remove the door panel.
  8.  
  9. Disconnect the lock lever cable and lever assembly. Remove the lock lever assembly.
  10.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Rear Door (Xterra)


Click image to see an enlarged view

Fig. Rear door panel and related components-2005 Xterra



Click image to see an enlarged view

Fig.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the power window switch assembly.
  6.  
  7. Remove the rear door finisher screw which is located behind the pull handle cover. Remove the pull handle cover.
  8.  
  9. Remove the pull handle escutcheon.
  10.  
  11. Remove the rear door finisher screws located behind the armrest. Lift upward to release the clips and remove the armrest.
  12.  
  13. Disconnect the rear door speaker, if equipped.
  14.  
  15. Release the clips and remove the door panel.
  16.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Door Lock Switch
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Carefully pry upward on the switch assembly.
  6.  
  7. Disconnect the electrical connectors from the switch assembly.
  8.  
  9. Remove the switch assembly.
  10.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

 
label.common.footer.alt.autozoneLogo