Nissan Murano 2003-05

Door Glass & Regulator

Print

Power Windows



Diagnosis & Testing


Click image to see an enlarged view

Fig. Power window components and harness connector locations



Click image to see an enlarged view

Fig. Power window wiring schematic-with intelligent key



Click image to see an enlarged view

Fig. Power window wiring schematic-without intelligent key

Removal & Installation
Motor & Regulator


Click image to see an enlarged view

Fig. Front and rear door panel and related components

Front Door


Click image to see an enlarged view

Fig. Front power window module assembly

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the cap from the inside handle portion of the door panel. Remove the screws.
  6.  
  7. Remove the inside handle escutcheon.
  8.  
  9. Remove the screw retaining the grip handle.
  10.  
  11. Remove the pull handle cap and remove the retaining screw.
  12.  
  13. Remove the power window switch. Disconnect the electrical connector.
  14.  
  15. Remove the screws on the power window switch side portion.
  16.  
  17. Insert a flat bladed tool between the panel on the vehicle and the retaining clips. Remove the door panel.
  18.  
  19. Pull up on the panel and remove the electrical connectors.
  20.  
  21. Remove the lock knob cable, inside handle cable and illumination harness connector from the backside of the inside handle assembly.
  22.  
  23. Remove the inside handle screws and completely remove the door panel from the vehicle.
  24.  
  25. Operate the power window switch to raise/lower the window until the glass bolts are visible.
  26.  
  27. Remove the glass bolts. Remove the module stop bolts.
  28.  
  29. Raise the door glass and hold it in position, using a suitable tool.
  30.  
  31. Remove the bolts and the module assembly from the vehicle.
  32.  
  33. Disconnect the harness connector from the module assembly and unclip the harness form the back of the module.
  34.  
  35. Separate the window motor from the module assembly.
  36.  

To install:

  1. To set the limit switch, remove the motor from the regulator.
  2.  
  3. Connect the connector. Rotate the motor unit with the power window switch for more than five seconds in the glass raising direction.
  4.  
  5. Install the motor in the regulator.
  6.  
  7. Raise the glass to the top position.
    NOTE
    Do not operate the window automatically to raise the glass to the top position.

  8.  
  9. Continue the installation in the reverse order of the removal procedure.
  10.  

Rear Door


Click image to see an enlarged view

Fig. Rear power window module assembly

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the cap from the inside handle portion of the door panel. Remove the screws.
  6.  
  7. Remove the inside handle escutcheon.
  8.  
  9. Remove the screw retaining the grip handle.
  10.  
  11. Remove the pull handle cap and remove the retaining screw.
  12.  
  13. Remove the power window switch. Disconnect the electrical connector.
  14.  
  15. Remove the screws on the power window switch side portion.
  16.  
  17. Insert a flat bladed tool between the panel on the vehicle and the retaining clips. Remove the door panel.
  18.  
  19. Pull up on the panel and remove the electrical connectors.
  20.  
  21. Remove the lock knob cable, inside handle cable and illumination harness connector from the backside of the inside handle assembly.
  22.  
  23. Remove the inside handle screws and completely remove the door panel from the vehicle.
  24.  
  25. Remove the rear door outside molding.
  26.  
  27. Remove the sealing screen.
  28.  
  29. Lower the door glass.
  30.  
  31. Remove the corner piece and screws and bolt.
  32.  
  33. Remove the corner piece assembly.
  34.  
  35. Operate the power window switch to raise/lower the window until the glass bolts are visible.
  36.  
  37. Remove the glass bolts. Remove the module stop bolts.
  38.  
  39. Raise the door glass and hold it in position, using a suitable tool.
  40.  
  41. Remove the bolts and the regulator assembly from the vehicle.
  42.  
  43. Disconnect the harness connector from the regulator assembly.
  44.  
  45. Separate the window motor from the regulator assembly.
  46.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Switch
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Carefully pry upward on the switch assembly.
  6.  
  7. Disconnect the electrical connectors from the switch assembly.
  8.  
  9. Remove the switch assembly.
  10.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

 
label.common.footer.alt.autozoneLogo