Nissan Quest 2001-02 and 2004-06

Removal & Installation

Print

Air Mix Motor



Front Driver-s Side
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the instrument lower panel LH.
  6.  
  7. Remove the center console.
  8.  
  9. Disconnect the air mix door motor electrical connector.
  10.  
  11. Remove the three screws and remove the air mix door motor.
  12.  
  13. To install, reverse removal procedure.
  14.  

Front Passenger-s Side
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the front heater and cooling unit assembly.
  6.  
  7. Remove the steering member from the front heater and cooling unit assembly.
  8.  
  9. Disconnect the air mix door motor electrical connector.
  10.  
  11. Remove the three screws and remove the air mix door motor.
  12.  
  13. To install, reverse removal procedure.
  14.  

Rear
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the rear lower finisher assembly.
  6.  
  7. Disconnect the rear air mix door motor electrical connector.
  8.  
  9. Remove the three screws and remove the rear air mix door motor.
  10.  
  11. To install, reverse removal procedure.
  12.  

Defroster Door Motor





Click image to see an enlarged view

Fig. View of defroster door motor

  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the front heater and cooling unit assembly.
  6.  
  7. Remove the steering member from the front heater and cooling unit assembly.
  8.  
  9. Disconnect the defroster door motor electrical connector.
  10.  
  11. Remove the two screws and remove the defroster door motor.
  12.  
  13. To install, reverse removal procedure.
  14.  

Intake Door Motor



Driver-s Side


Click image to see an enlarged view

Fig. View of intake door motor-driver-s side

  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the instrument lower panel LH.
  6.  
  7. Remove the center console.
  8.  
  9. Disconnect the intake door motor electrical connector.
  10.  
  11. Remove the three screws and remove the intake door motor.
  12.  
  13. To install, reverse removal procedure.
  14.  

Passenger-s Side


Click image to see an enlarged view

Fig. View of intake door motor-passenger-s side

  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the front heater and cooling unit assembly.
  6.  
  7. Remove the steering member from the front heater and cooling unit assembly.
  8.  
  9. Disconnect the intake door motor electrical connector.
  10.  
  11. Remove the three screws and remove the intake door motor.
  12.  
  13. To install, reverse removal procedure.
  14.  

Mode Door Motor



  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the instrument lower panel RH and glove box.
  6.  
  7. Remove the center console.
  8.  
  9. Disconnect the mode door motor electrical connector.
  10.  
  11. Remove the three screws and remove the mode door motor.
  12.  
  13. To install, reverse removal procedure.
  14.  

 
AutoZone Logo