PT Cruiser, 2001 - 2005

2.4L L4 VIN 8 Std

Print

2.4L L4 VIN 8 Std

Trouble Code: P0016

Crankshaft/Camshaft Timing Misalignment

Trouble Code Conditions: Engine cranking or running; and the PCM detected the camshaft was out of phase with the crankshaft during the CCM test period.

Possible Causes:



Base engine problem (i.e., the camshaft timing is not correct)
 
Intermittent condition
 
CKP or CMP Sensor signal is erratic (check with lab scope)
 
Tone wheel or pulse wheel is damaged or contains debris
 
CKP or CMP Sensor, harness or connector has failed
 
PCM has failed
 

Trouble Code: P0031

O2 (B1 S1) Heater Circuit Low

Trouble Code Conditions: Key on; system voltage over 10.6v; ASD relay on; O2 heater "on". The PCM detected the O2 Heater circuit is out of acceptable range low.

Possible Causes:



O2 assembly is damaged or it has failed
 
O2 heater element is damaged or has failed
 
O2 heater control circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0032

O2 (B1 S1) Heater Circuit High

Trouble Code Conditions: Key on; system voltage over 10.6v; ASD relay on; O2 heater "off". The PCM detected the O2 Heater circuit is out of range high.

Possible Causes:



O2 heater element is damaged or the heater has failed
 
O2 heater control circuit is open or it is shorted to power
 
O2 heater ground circuit is open
 
PCM has failed
 

Trouble Code: P0033

Surge Valve Solenoid Circuit Fault

Trouble Code Conditions: Key on or engine running; system voltage over 10v. The PCM detected the Actual state of the Surge Valve solenoid circuit did not match the Intended state during the CCM test.

Possible Causes:



Surge valve power supply is open (test power from ASD relay)
 
Surge valve solenoid circuit is open
 
Surge valve solenoid circuit is shorted to ground or power (B+)
 
Surge valve solenoid is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0037

O2 (B1 S2) Heater Circuit Low

Trouble Code Conditions: Key on; system voltage over 10.6v; ASD relay on; O2 heater "on". The PCM detected the O2 Heater circuit is out of acceptable range (i.e., below 0.0926v).

Possible Causes:



O2 assembly is damaged or it has failed
 
O2 heater element is damaged or has failed
 
O2 heater control circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0038

O2 (B1 S2) Heater Circuit High

Trouble Code Conditions: Key on; system voltage over 10.6v; ASD relay on; O2 heater "off". The PCM detected the O2 heater voltage is out of range high.

Possible Causes:



O2 Sensor failed or improper operation
 
O2 heater element is damaged or failed
 
O2 heater control circuit is open or it is shorted to power
 
O2 heater ground circuit is open
 
PCM has failed
 

Trouble Code: P0051

O2 (B2 S1) Heater Relay Circuit Low

Trouble Code Conditions: Key on, system voltage over 10.6v, ASD relay on, O2 heater "on", and the PCM detected the Heater Relay circuit Actual state did not match the Desired state (low circuit). 3 good trips are required to turn off the MIL.

Possible Causes:



O2 assembly is damaged or it has failed
 
O2 heater element is damaged or has failed
 
O2 heater control circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0052

O2 (B2 S1) Heater Relay Circuit High

Trouble Code Conditions: Key on, system voltage over 10.6v, ASD relay on, O2 heater "off", and the PCM detected the Heater Relay circuit Actual state did not match the Desired state (high circuit).

Possible Causes:



O2 heater element is damaged or the heater has failed
 
O2 heater control circuit is open or it is shorted to power
 
O2 heater ground circuit is open
 
PCM has failed
 

Trouble Code: P0057

O2 (B2 S2) Heater Relay Circuit Low

Trouble Code Conditions: Key on, system voltage over 10.6v, ECT input under test condition value, and the PCM detected the Heater Relay signal was too low.

Possible Causes:



O2 assembly is damaged or it has failed
 
O2 heater element is damaged or has failed
 
O2 heater control circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0058

O2 (B2 S2) Heater Relay Circuit High

Trouble Code Conditions: Key on, system voltage over 10.6v, ASD powered up, and O2 heater is off. ECT input under test condition value and the PCM detected the Heater Relay signal was too high.

Possible Causes:



O2 heater element is damaged or the heater has failed
 
O2 heater control circuit is open or it is shorted to power
 
O2 heater ground circuit is open
 
PCM has failed
 

Trouble Code: P0068

MAP Sensor/TP Sensor Correction - High Flow/Vacuum Leak

Trouble Code Conditions: Engine started; engine speed over 2000 rpm, and the PCM detected the Manifold Air Pressure (MAP) value dropped to less than 1.5" Hg with the throttle closed during the test.

Possible Causes:



An engine vacuum leak present
 
High resistance in the MAP ground circuit, MAP Sensor signal or VREF (5v) circuit
 
High resistance in the TP ground, TP circuit or the TP Sensor VREF (5v) circuit
 
MAP Sensor is damaged or it has failed
 
TP Sensor is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0071

Ambient Temperature Sensor Performance

Trouble Code Conditions: Engine "off" time over 8 hours; DTC P0072 and P0073 not set; ambient temperature more than 38ºF (4C). The PCM determined the Ambient Air Temperature (AAT) Sensor was not within calibrated temperature of the ECT and IAT Sensor signals after a cool down period.

Possible Causes:



AAT Sensor circuit open, shorted to ground or VREF
 
AAT Sensor voltage below 1.0v
 
AAT signal circuit is open or is shorted to ground, to battery voltage or to Sensor ground
 
AAT Sensor ground circuit is open
 
AAT Sensor is damaged or it has failed
 
PCM High or Low circuit is damaged or it has failed
 

Trouble Code: P0072

Ambient Temperature Sensor Circuit Low Input

Trouble Code Conditions: Related DTCs not set, key on or engine running; system voltage over 10.5v, at least 5 warm-up cycles completed, odometer mileage change at least 196.6 miles, and the PCM detected the AAT Sensor signal was less than 0.3v (0.78v: Jeep) at PCM. 3 good trips required to turn off MIL.

Possible Causes:



AAT Sensor internal failure
 
AAT signal circuit shorted to ground
 
AAT signal circuit shorted to Sensor ground
 
PCM has failed
 

Trouble Code: P0073

Ambient Temperature Sensor Circuit High Input

Trouble Code Conditions: Key on or engine running; system voltage over 10.0v and the PCM detected the Ambient Air Temperature (AAT) Sensor signal was more than 4.9v for more than 2.8 seconds. Note that this code can be set due to an intermittent failure. 3 good trips are required to turn off the MIL.

Possible Causes:



AAT Sensor signal shorted to VREF (5v) or battery voltage
 
AAT Sensor signal circuit or Sensor ground circuit is open
 
AAT Sensor is damaged (it may be open)
 
PCM has failed
 

Trouble Code: P0107

MAP Sensor Circuit Low Input

Trouble Code Conditions: Ignition on or engine from 600-3500 rpm (416-1500 rpm: Viper); TP Sensor input less than 1.2v (exc. Ram, Viper, Jeep), less than 0.8v (Ram, Jeep) or less than 1.13v (Viper). Battery voltage greater than 10v. MAP Sensor signal voltage was less than 0.782v for 1.7 seconds (exc. Dakota, Durango, Viper, Jeep) or less than 0.08v for 3 seconds (Dakota, Durango, Jeep), less than 0.1v for 2 seconds (Viper). If equipped, ETC light will flash.

Possible Causes:



5-volt supply circuit is open or shorted to ground
 
MAP Sensor signal circuit is shorted to ground or shorted to Sensor ground circuit
 
MAP Sensor has failed
 
PCM 5-volt supply circuit has failed
 

Trouble Code: P0108

MAP Sensor Circuit High Input

Trouble Code Conditions: Ignition on or engine speed from 600-3500 rpm (above 400 for Viper); TP Sensor input more than 1.2v, for more than 1.7 seconds; battery voltage over 10.0v. The PCM detected the MAP Sensor signal voltage (input) was over 4.92v (exc. Viper), or was greater than 4.88v at start or with engine running for 2.2 seconds (Viper).

Possible Causes:



MAP Sensor signal circuit is open
 
MAP Sensor ground circuit is open
 
MAP Sensor signal circuit shorted to 5-volt supply circuit or to battery voltage
 
MAP Sensor has failed or it has failed (possible open circuit)
 
MAP Sensor has failed
 
PCM has failed
 

Trouble Code: P0111

IAT Sensor Performance

Trouble Code Conditions: DTC P0112 and P0113 not set, key on, ECT Sensor input more than 160ºF at startup, at least 5 warm-up cycles have occurred with vehicle mileage change of more than 196.6 miles, and the PCM detected the IAT input changed less than 5.4ºF during this period.

Possible Causes:



IAT Sensor signal circuit is open, shorted to ground or VREF
 
IAT Sensor ground circuit is open
 
IAT Sensor is damaged or it has failed
 
PCM High or Low circuit is damaged or it has failed
 

Trouble Code: P0112

IAT Sensor Circuit Low Input

Trouble Code Conditions: Ignition on or engine started; battery voltage greater than 10v. If the PCM detected an IAT Sensor input of less than 0.1v (Neon), 0.157v (Cirrus/Sebring, Stratus, Caravan/Town & Country) or less than 0.078v (Durango, Ram, Grand Cherokee) for 3 seconds, less than 0.8v (Viper), or less than 0.5v (Liberty) this DTC will set.

Possible Causes:



IAT Sensor signal circuit is shorted to chassis ground
 
IAT Sensor signal circuit is shorted to Sensor ground
 
IAT Sensor is damaged or it has failed (an internal short circuit)
 
PCM has failed
 

Trouble Code: P0113

IAT Sensor Circuit High Input

Trouble Code Conditions: Check with ignition on or engine running; battery voltage more than 10v; The PCM detected the IAT Sensor input was over 4.90v (exc. Dakota, Durango, Ram) or 4.98v (Dakota, Durango, Ram) for 3 seconds.

Possible Causes:



IAT Sensor signal circuit shorted to VREF (5v)
 
IAT Sensor signal circuit is open, or the ground circuit is open
 
IAT Sensor is damaged or it has failed (an internal open circuit)
 
PCM has failed
 

Trouble Code: P0116

ECT Sensor Circuit Performance

Trouble Code Conditions: Engine off time is more than 8 hours; ambient temperature is more than 38F (4C); and after a calibrated amount of cool-down time, the PCM compares the ECT Sensor, IAT Sensor and AAT Sensor values; if ECT Sensor is not within a calibrated temperature amount of the other 2 Sensors, an error is detected. 3 good trips are required to turn off the MIL. If equipped, the ECT light will also illuminate when the MIL illuminates.

Possible Causes:



ECT Sensor signal circuit is open or it is shorted battery voltage or to ground
 
ECT Sensor signal circuit is shorted to Sensor ground
 
ECT Sensor ground circuit is open
 
ECT Sensor is damaged or it has failed
 
PCM High or Low circuit is damaged or it has failed
 

Trouble Code: P0117

ECT Sensor Circuit Low Input

Trouble Code Conditions: Ignition on or engine started. The PCM detected the ECT Sensor input voltage was below 0.51v (95-03) or 0.1v (04-05, exc. Grand Cherokee, Liberty), less than 0.5v (04-05 Liberty), less than 0.78v (Grand Cherokee), or below 0.8v (Viper) for 3 seconds.

Possible Causes:



ECT Sensor signal circuit is shorted to chassis ground
 
ECT Sensor signal circuit is shorted to Sensor ground
 
ECT Sensor is damaged or it has failed (it may be shorted)
 
PCM has failed
 

Trouble Code: P0118

ECT Sensor Circuit High Input

Trouble Code Conditions: Ignition on or engine started and the PCM detected the ECT Sensor input was over 4.9v for 3 seconds. If equipped, the ETC lamp will illuminate with the MIL. 3 good trips are required to turn off the MIL.

Possible Causes:



ECT Sensor signal circuit is shorted to VREF (5v)
 
ECT Sensor signal circuit is open
 
ECT Sensor ground circuit is open
 
ECT Sensor is damaged or it has failed (possible open circuit)
 
PCM has failed
 

Trouble Code: P0122

TP Sensor No. 1 Circuit Low Input

Trouble Code Conditions: Key on; system voltage over 10v; and the PCM detected the TP Sensor indicated less than 0.16v for 0.7 second (300M, Magnum, Liberty), 0.078v (Pacifica, PT Cruiser), or 0.0978v (Neon, Sebring, Stratus) or 0.1v (Viper). 3 good trips are required to turn off the MIL. If equipped, the ETC light will illuminate.

Possible Causes:



TP Sensor sweep
 
Intermittent condition
 
5v supply circuit open or shorted to ground
 
TP Sensor No. 1 signal circuit shorted to ground or to Sensor return circuit
 
TP Sensor or throttle body damaged or has failed
 
PCM has failed
 

Trouble Code: P0123

TP Sensor/APPS Circuit High Input

Trouble Code Conditions: Key on or engine running; system voltage over 10v. The PCM detected the TP Sensor indicated more than 4.47v (Neon, Sebring, Stratus, Viper, Liberty) or 4.94v (all other models) for 0.48 second. If equipped, ETC light will illuminate.

Possible Causes:



Related TP Sensor engine DTCs present
 
Intermittent wiring or connector problem
 
TP signal circuit is open or is shorted to battery voltage or to 5v supply circuit
 
TP sensor has failed
 
TP sensor ground circuit is open
 
PCM has failed
 

Trouble Code: P0124

TP Sensor/APPS Circuit Intermittent

Trouble Code Conditions: Key on or engine running; system voltage over 10.5v. This DTC will set if the monitored TP Sensor angle between 6-120 and the degree change is greater than 5 within a period of less than 7.0ms.

Possible Causes:



Related TP Sensor engine DTCs present
 
TP Sensor has failed
 
Intermittent wiring or connector problem
 
PCM has failed
 

Trouble Code: P0125

Closed Loop Temperature Not Reached

Trouble Code Conditions: Engine running; battery over 10v. Engine temperature does not enable closed loop. Failure time depends on start-up coolant temperature and ambient temperature (i.e., 2 minutes for a start temperature of 50ºF (10C), or up to 10 minutes for a vehicle with start-up temperature of -18F (-28C).

Possible Causes:



Low coolant level
 
Improper thermostat operation or thermostat failure
 
ECT has failed
 

Trouble Code: P0128

Thermostat Rationality Test

Trouble Code Conditions: With engine running after cold start. PCM predicts a coolant temperature value that it will compare to the actual coolant temperature. If the 2 coolant temperature values are not within 50ºF (10ºC) of each other, an error is detected.

Possible Causes:



Low coolant level
 
Thermostat has failed
 
Signal circuit shorted to battery voltage
 
ECT Sensor has failed or voltage is below 1.0v
 
Signal circuit is open, shorted to ground or shorted to Sensor ground
 
ECT Sensor ground circuit or signal circuit is open
 
PCM has failed
 

Trouble Code: P0129

Barometric Pressure Out-Of-Range

Trouble Code Conditions: Engine cranking at less than 250 rpm; no CKP or CMP Sensor signals within 75ms. The PCM detected the MAP/BARO Sensor signal range was 0.04-2.2v for 300ms during testing. If equipped, the ETC lamp will be illuminated. 3 good trips are required to turn off the MIL.

Possible Causes:



IAC motor control low or control high circuit has failed
 
MAP Sensor VREF (5v) circuit is open or shorted to ground
 
MAP Sensor signal circuit is open or shorted to ground
 
MAP Sensor is damaged or it has failed
 
May be an intermittent condition
 
PCM has failed
 

Trouble Code: P0131

O2 (B1 S1) Circuit Short to Ground

Trouble Code Conditions: Engine running; cold start. O2 Sensor signal voltage is below 2.402v for 9 seconds (exc. Durango, Grand Cherokee, Liberty, Ram, Viper), or below 2.52v for 6 seconds (Durango, Grand Cherokee, Liberty, Ram), or below 0.156v for 28 seconds (Viper).

Possible Causes:



O2 signal circuit is shorted to chassis or Sensor ground
 
O2 return circuit is shorted to ground or to signal circuit
 
O2 signal circuit is shorted to O2 return upstream circuit
 
O2 may be contaminated or it has failed
 
PCM has failed
 

Trouble Code: P0132

O2 Sensor (B1 S1) Voltage High

Trouble Code Conditions: Engine started; engine runtime over 119 seconds. Battery voltage over 10.99v. O2 Sensor heater temperature is more than 662F (350C). O2 Sensor voltage is more than 3.7v for 60 seconds (Pacifica), more than 3.99v for 60 seconds (Neon, Sebring, Stratus, PT Cruiser), or more than 3.9902v for 30 seconds (Caravan/Town & Country), or more than 3.99v for 66.56 seconds (Liberty).

Possible Causes:



O2 Sensor signal circuit and/or return circuit shorted to voltage
 
O2 Sensor has failed
 
O2 Sensor signal or return circuit open
 
PCM has failed
 

Trouble Code: P0133

O2 (B1 S1) Slow Response

Trouble Code Conditions: Vehicle driven at speeds between 20-55 mph, with throttle open for minimum of 120 seconds; coolant temperature is greater than 158F (70C); catalytic converter temperature is greater than 1112F (600C). PCM compared differences (state of change) between front and rear O2 Sensors indicate difference is greater than calibrated amount.

Possible Causes:



Exhaust leak present in the exhaust manifold or exhaust pipes
 
O2 signal circuit or return circuit has failed
 
O2 element has failed
 

Trouble Code: P0135

O2 (B1 S1) Heater Circuit

Trouble Code Conditions: Engine running and O2 heater duty cycle is greater than 0%. O2 heater temperature does not reach 959F (575C), exc. PT Cruiser, or 662F (350C), Neon and PT Cruiser, within 90 seconds (Sebring, Stratus, 45 seconds) during monitoring conditions. No Sensor output is received when the PCM powers up the Sensor heater. 3 good trips are required to turn off the MIL.

Possible Causes:



O2 heater ground circuit open or O2 signal circuit is open
 
O2 heater element has failed
 
PCM has failed
 

Trouble Code: P0137

O2 (B1 S2) Sensor Circuit Low

Trouble Code Conditions: Engine running; battery voltage over 10.9v; O2 heater temperature below 484ºF (251C) or ECT above 170F from previous key off. The PCM detected the O2 Sensor signal voltage was less than 1.5v for 3 seconds (300M, Magnum), less than 2.402v for 9 seconds (Neon, Sebring, Stratus, PT Cruiser, Caravan, Town & Country, Liberty), or 2.5194v for 3 seconds (Durango, Ram), or less than 0.156v for 28 seconds (Viper).

Possible Causes:



O2 return circuit is shorted to ground
 
O2 signal circuit is shorted to ground, or to O2 return circuit, or O2 heater ground circuit
 
O2 Sensor has failed
 
PCM has failed
 

Trouble Code: P0138

O2 (B1 S2) Sensor Voltage High Condition:

Trouble Code Conditions: Engine runtime for 119 seconds; O2 Sensor heater temperature is more than 662ºF (350ºC); Battery voltage more than 10.99v. O2 Sensor voltage is above 3.7v for 60 seconds (300M, Magnum, Pacifica), or 3.99v for 60 seconds (PT Cruiser, Sebring, Stratus), above 3.9902v for 30 seconds (Neon, Caravan, Dakota, Durango, Grand Cherokee, Ram, Town & Country, Voyager, Wrangler), or above 3.99v for 76.8 seconds (Liberty).

Possible Causes:



O2 Sensor signal circuit or return circuit shorted to voltage
 
O2 Sensor has failed
 
O2 Sensor signal circuit or return circuit open
 
PCM has failed
 

Trouble Code: P0139

O2 (B1 S2) Slow Response

Trouble Code Conditions: Engine started; vehicle driven at 20-55 mph with the throttle open for 2 minutes; ECT at more than 158ºF (70C); catalytic converter temperature is more than 1112F (600C); and EVAP purge is active. O2 Sensor signal voltage switches less than 16 times from lean to rich within 20 seconds during monitoring, or will compare the state of change between the front and rear O2 Sensors and if the differences are greater than a calibrated amount, the DTC will set. 3 good trips are required to turn off the MIL.

Possible Causes:



Exhaust leak
 
O2 element is contaminated, deteriorated or it has failed
 
O2 signal circuit or return circuit has failed
 

Trouble Code: P0141

O2 (B1 S2) Heater Circuit

Trouble Code Conditions: Engine running and O2 heater duty cycle is greater than 0%. O2 heater temperature does not reach 959F (575C), exc. 300M, Magnum, or 662F (350C), all other models, within 90 seconds (45 seconds for Sebring, Stratus), or no O2 Sensor output is received when the PCM attempts to power up the Sensor heater. 3 good trips are required to turn off the MIL.

Possible Causes:



O2 heater ground circuit open or O2 signal circuit is open
 
O2 heater element has failed
 
O2 heater ground circuit or control circuit is open
 
PCM has failed
 

Trouble Code: P0152

O2 (B2 S1) Circuit High

Trouble Code Conditions: O2 Sensor heater temperature is more than 925F (496C) on 300M, Magnum or 1085F (350C) on Sebring; battery voltage is more than 10.99v. O2 Sensor voltage is more than 3.7v for 30 seconds (300M, Magnum), more than 3.99v for 30 seconds (Dakota, Durango, Grand Cherokee, Ram, Wrangler), 3.99v for 60 seconds (Sebring, Stratus), or 3.99v for 66.56 seconds (Liberty). 3 good trips are required to turn off the MIL.

Possible Causes:



O2 signal circuit is open or is shorted to battery voltage.
 
O2 upstream return circuit is open or is shorted to battery voltage
 
O2 Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0153

O2 (B2 S1) Slow Response

Trouble Code Conditions: Engine started; vehicle driven at a steady speed of 20-55 mph with the throttle open for at least 2 minutes, ECT Sensor more than 158ºF (70C), Catalytic Converter temperature more than 1112ºF (600C), EVAP purge is active, and the PCM detected the O2 signal switched from lean to rich less than 16 times (3.5L, 3.7L, 4.7L, 5.7L) or 11 times (2.7L) within a 20 second period during monitoring. 3 good trips are required to turn off MIL.

Possible Causes:



Exhaust leak
 
O2 signal circuit has an open or grounded condition
 
O2 upstream return circuit has an open or grounded condition
 
O2 element is deteriorated or it has failed
 

Trouble Code: P0155

O2 (B2 S1) Heater Circuit

Trouble Code Conditions: Engine running and heater duty cycle is greater than 0%; battery voltage is more than 11v. O2 heater temperature does not reach 959F (575C) within 90 seconds, or no Sensor output is received when the PCM powers up the Sensor heater. 3 good trips required to turn off MIL.

Possible Causes:



O2 heater control circuit is open
 
O2 heater ground circuit is open
 
O2 heater element is damaged or has failed
 
PCM has failed
 

Trouble Code: P0157

O2 (B2 S2) Circuit Low

Trouble Code Conditions: Engine runtime under 30 seconds; system voltage over 10.99v; O2 heater temperature below 484ºF (251ºC); O2 Sensor signal was less than 1.5v (300M, Magnum, Viper) or less than 2.5196v (Durango, Grand Cherokee, Ram, Wrangler) for 3 seconds (28 seconds: Viper), or below 2.411v for 10 seconds (Liberty) after engine start. 3 good trips are required to turn off the MIL.

Possible Causes:



O2 signal circuit is shorted to chassis or Sensor ground
 
O2 is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0158

O2 (B2 S2) Circuit High

Trouble Code Conditions: Engine is running; system voltage over 10.99v; O2 heater temperature more than 925ºF (496ºC) on all exc. Sebring, Stratus, or more than 1085F (350C) on Sebring, Stratus. The PCM detected the O2 signal was more than 3.70v for 30 seconds (300M, Magnum), more than 3.99v for 30 seconds (Dakota, Durango, Grand Cherokee, Ram, Wrangler), more than 3.99v for 60 seconds (Sebring, Stratus), or more than 3.99v for 76.8 seconds (Liberty). 3 good trips required to turn off MIL.

Possible Causes:



O2 signal circuit is open or is shorted to battery
 
O2 downstream return circuit is open or is shorted to battery
 
O2 is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0159

O2 (B2 S2) Slow Response

Trouble Code Conditions: Engine is driven at 20-55 mph with throttle open for 2 minutes; ECT Sensor over 158ºF (70C); catalytic converter temperature over 1112ºF (600C); EVAP purge is active. The O2 Sensor signal voltage switches less than 16 times or 11 times (2.7L exc. Liberty) from lean to rich with 20 seconds during monitoring. 3 good trips required to turn off MIL.

Possible Causes:



Exhaust leak
 
O2 signal circuit is open or shorted
 
O2 downstream return circuit is open or shorted
 
O2 Sensor is damaged or has failed
 

Trouble Code: P0171

Fuel System Lean (B1 S1)

Trouble Code Conditions: Engine running in closed loop. AAT Sensor signal over 20ºF (-7C). Altitude less than 8,500 feet. Fuel level greater than 15%. If PCM multiplies short-term compensation by long-term adaptive and a certain percentage is exceeded for 2 trips, a freeze frame is stored, the MIL illuminates, and a DTC is stored.

Possible Causes:



Restricted fuel supply line
 
Fuel pump inlet strainer plugged or fuel pump has failed
 
O2 Sensor has failed
 
O2 signal circuit or return circuit has failed
 
O2 Sensor heater operation is faulty
 
TP Sensor sweep has failed
 
MAP Sensor operation has failed
 
ECT Sensor operation has failed
 
Engine mechanical problem is present
 
Fuel is contaminated
 
Exhaust leak exists
 

Trouble Code: P0172

Fuel System (S1 B1) Rich

Trouble Code Conditions: Engine running in closed loop. IAT Sensor signal over 20ºF (-7C). Altitude less than 8,500 feet. PCM multiplies short-term compensation by long-term adaptive, as well as a purge fuel multiplier, and the result is below a certain value for 30 seconds over 2 trips, a freeze frame is stored. MIL illuminates and DTC is stored.

Possible Causes:



O2 Sensor heater or O2 Sensor has failed
 
EVAP purge solenoid failed or improper operation
 
O2 signal circuit or return circuit has failed
 
MAP Sensor has failed or circuit malfunction
 
ECT Sensor has failed or circuit malfunction
 
Engine mechanical problem
 
Fuel filter/pressure regulator has failed or needs repair
 
PCM has failed
 

Trouble Code: P0174

Fuel System (S2 B1) Lean

Trouble Code Conditions: Engine running in closed loop. IAT Sensor signal over 20ºF (-7C). Altitude less than 8,500 feet. PCM multiplies short-term compensation by long-term adaptive, and a certain percentage is exceeded in 2 trips, a freeze frame is stored. MIL illuminates and DTC is stored. 3 good trips required to turn off MIL.

Possible Causes:



Restricted fuel supply line
 
Fuel pump inlet strainer plugged
 
Fuel pump is damaged or has failed
 
O2 signal circuit or return circuit has failed
 
MAP Sensor has failed or circuit malfunction
 
ECT Sensor has failed or circuit malfunction
 
Engine mechanical problem
 
Fuel filter/pressure regulator has failed or needs repair
 
O2 Sensor has failed
 
PCM has failed
 

Trouble Code: P0175

Fuel System (S2 B1) Rich

Trouble Code Conditions: Engine running in closed loop. IAT Sensor signal over 20ºF (-7C). Altitude less than 8,500 feet. If the PCM multiplies short-term compensation by long-term adaptive, and a purge fuel multiplier, and the result is below a certain value for 30 seconds in 2 trips, a freeze frame is stored. MIL illuminates and DTC is stored. 3 good trips required to turn off MIL.

Possible Causes:



Restricted fuel supply line
 
Fuel pump inlet strainer plugged
 
Fuel pump is damaged or has failed
 
O2 signal circuit or return circuit has failed
 
MAP Sensor has failed or circuit malfunction
 
ECT Sensor has failed or circuit malfunction
 
Engine mechanical problem
 
Fuel filter/pressure regulator has failed or needs repair
 
O2 Sensor has failed
 
PCM has failed
 

Trouble Code: P0196

Engine Oil Temperature Sensor Circuit Performance

Trouble Code Conditions: Engine off time is more than 8 hours; ambient temperature is more than 38F (4C). If the PCM detects the engine oil temperature value is incorrect, by comparing it with other engine inputs, then the DTC will set. 3 good trips required to turn off MIL.

Possible Causes:



Engine oil temp signal circuit is open or is shorted to ground or to battery voltage
 
Engine oil temp Sensor ground circuit is open
 
Engine oil temp signal circuit is shorted to Sensor ground
 
Engine oil temp Sensor has failed
 
PCM has failed
 

Trouble Code: P0197

Engine Oil Temperature Sensor Circuit Low

Trouble Code Conditions: Ignition is on; battery voltage is more than 10.4v. The engine oil temperature Sensor circuit voltage at the PCM is less than the calibrated amount. 3 good trips required to turn off MIL.

Possible Causes:



Engine oil temp signal circuit is shorted to ground
 
Engine oil temp signal circuit is shorted to Sensor ground
 
Engine oil temp Sensor has failed
 
PCM has failed
 

Trouble Code: P0198

Engine Oil Temperature Sensor Circuit High

Trouble Code Conditions: Ignition is on; battery voltage is more than 10.4v. The engine oil temperature Sensor circuit voltage at the PCM is higher than the calibrated amount. 3 good trips required to turn off MIL.

Possible Causes:



Engine oil temp signal circuit is open or is shorted to battery voltage
 
Engine oil temp Sensor ground circuit is open
 
Engine oil temp Sensor has failed
 
PCM has failed
 

Trouble Code: P0201

Fuel Injector 1, 2, 3 or 4 Control Circuit Open

Trouble Code Conditions: Ignition on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is open.

Possible Causes:



Intermittent condition
 
Fuel injector 1-4 control circuit is open
 
Fuel injector 1-4 ASD relay output circuit is open
 
Fuel injector driver circuit is open
 
Fuel injector is clogged or has failed
 
PCM has failed
 

Trouble Code: P0202

Fuel Injector 1, 2, 3 or 4 Control Circuit Open

Trouble Code Conditions: Ignition on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is open.

Possible Causes:



Intermittent condition
 
Fuel injector 1-4 control circuit is open
 
Fuel injector 1-4 ASD relay output circuit is open
 
Fuel injector driver circuit is open
 
Fuel injector is clogged or has failed
 
PCM has failed
 

Trouble Code: P0203

Fuel Injector 1, 2, 3 or 4 Control Circuit Open

Trouble Code Conditions: Ignition on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is open.

Possible Causes:



Intermittent condition
 
Fuel injector 1-4 control circuit is open
 
Fuel injector 1-4 ASD relay output circuit is open
 
Fuel injector driver circuit is open
 
Fuel injector is clogged or has failed
 
PCM has failed
 

Trouble Code: P0204

Fuel Injector 1, 2, 3 or 4 Control Circuit Open

Trouble Code Conditions: Ignition on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is open.

Possible Causes:



Intermittent condition
 
Fuel injector 1-4 control circuit is open
 
Fuel injector 1-4 ASD relay output circuit is open
 
Fuel injector driver circuit is open
 
Fuel injector is clogged or has failed
 
PCM has failed
 

Trouble Code: P0201

Injector 1, 2, 3, 4, 5, or 6 Control

Trouble Code Conditions: ASD relay "on"; engine speed under 3000 rpm; battery voltage greater than 10v (11.9981v: Liberty). No inductive spike is detected after injector turns off.

Possible Causes:



ASD relay output circuit failure
 
Fuel injector has malfunctioned or failed
 
Fuel injector control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0202

Injector 1, 2, 3, 4, 5, or 6 Control

Trouble Code Conditions: ASD relay "on"; engine speed under 3000 rpm; battery voltage greater than 10v (11.9981v: Liberty). No inductive spike is detected after injector turns off.

Possible Causes:



ASD relay output circuit failure
 
Fuel injector has malfunctioned or failed
 
Fuel injector control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0203

Injector 1, 2, 3, 4, 5, or 6 Control

Trouble Code Conditions: ASD relay "on"; engine speed under 3000 rpm; battery voltage greater than 10v (11.9981v: Liberty). No inductive spike is detected after injector turns off.

Possible Causes:



ASD relay output circuit failure
 
Fuel injector has malfunctioned or failed
 
Fuel injector control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0204

Injector 1, 2, 3, 4, 5, or 6 Control

Trouble Code Conditions: ASD relay "on"; engine speed under 3000 rpm; battery voltage greater than 10v (11.9981v: Liberty). No inductive spike is detected after injector turns off.

Possible Causes:



ASD relay output circuit failure
 
Fuel injector has malfunctioned or failed
 
Fuel injector control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0205

Injector 1, 2, 3, 4, 5, or 6 Control

Trouble Code Conditions: ASD relay "on"; engine speed under 3000 rpm; battery voltage greater than 10v (11.9981v: Liberty). No inductive spike is detected after injector turns off.

Possible Causes:



ASD relay output circuit failure
 
Fuel injector has malfunctioned or failed
 
Fuel injector control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0206

Injector 1, 2, 3, 4, 5, or 6 Control

Trouble Code Conditions: ASD relay "on"; engine speed under 3000 rpm; battery voltage greater than 10v (11.9981v: Liberty). No inductive spike is detected after injector turns off.

Possible Causes:



ASD relay output circuit failure
 
Fuel injector has malfunctioned or failed
 
Fuel injector control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0218

A/T High Temperature Operation Activated

Trouble Code Conditions: Engine started; vehicle driven in gear, and the TCM indicated the Overheat shift schedule was activated (i.e., the TCM had detected a transmission oil temperature of more than 240ºF). Note: This is an informational DTC, designed to aid the technician in diagnosing shift quality complaints.

Possible Causes:



Engine cooling system malfunction present
 
High temperature operations activated
 
Transmission oil pump flow is too low or it is restricted
 

Trouble Code: P0221

Throttle Position Sensor No. 2 Performance

Trouble Code Conditions: Ignition on; No MAP Sensor DTCs are set. TP Sensor signals Do NOT correlate to the MAP Sensor signal. If equipped, ETC light will illuminate. P2135 should also set.

Possible Causes:



TP Sensor No. 1 or 2 signal circuit is shorted to battery voltage or to ground
 
TP Sensor No. 1 or 2 signal circuit has high resistance
 
5v supply circuit is shorted to ground
 
TP Sensor return circuit has high resistance
 
TP Sensor No. 1 signal circuit shorted to TP Sensor No. 2 signal circuit
 
TP Sensor or throttle body damaged or has failed
 
PCM has failed
 

Trouble Code: P0223

Throttle Position Sensor No. 2 Circuit High

Trouble Code Conditions: Ignition on; battery voltage is more than 10v. TP Sensor voltage at the PCM is more than 4.9v for 25ms. If equipped, ETC light will illuminate.

Possible Causes:



TP Sensor No. 2 signal circuit shorted to battery voltage or to 5v supply circuit
 
TP Sensor return circuit is open
 
TP Sensor or throttle body is damaged or has failed
 
PCM has failed
 

Trouble Code: P0261

Injector No. 1 Control Circuit Low

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to ground. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0262

Injector No. 1 Control Circuit High

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to voltage. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ASD relay output circuit or to battery voltage
 
PCM has failed
 

Trouble Code: P0264

Injector No. 2 Control Circuit Low

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to ground. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0265

Injector No. 2 Control Circuit High

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to voltage. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ASD relay output circuit or to battery voltage
 
PCM has failed
 

Trouble Code: P0267

Injector No. 3 Control Circuit Low

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to ground. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0268

Injector No. 3 Control Circuit High

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to voltage. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ASD relay output circuit or to battery voltage
 
PCM has failed
 

Trouble Code: P0270

Injector No. 4 Control Circuit Low

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to ground. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0271

Injector No. 4 Control Circuit High

Trouble Code Conditions: Ignition is on. The PCM tests the injector circuit internally for more than 27 injector pulses and has determined that the circuit is shorted to voltage. MIL is illuminated.

Possible Causes:



Intermittent condition
 
Fuel injector has malfunctioned or failed
 
ASD relay output circuit is open
 
Fuel injector driver circuit is shorted to ASD relay output circuit or to battery voltage
 
PCM has failed
 

Trouble Code: P0300

Multiple Cylinder Misfire

Trouble Code Conditions: Engine is running; atmospheric pressure, fuel level, battery voltage, engine speed, engine load are above minimal predetermined specifications; the engine is not in fuel cutoff and intake air temperature and coolant temperature are within normal operating ranges; there are no DTCs relating to MAP, ECT, CMP, CKP or IAT Sensor, to Crank rationality, to Crank Sensor Learn invalid, or to System Voltage. If total misfires detected are greater than 8.5% during the first 1000 rpm, or are 40% during any 200 rpm, with no single cylinder or multiple cylinder misfire counters above 80%, this DTC will set. The MIL will flash after first trip occurrence and will be steady after second trip.

Possible Causes:



Fuel system problems exist
 
Erratic CMP or CKP Sensor signals
 
Ignition system problems exist
 
Engine mechanical problems exist
 
PCM has failed
 

Trouble Code: P0301

Cylinder No. 1, 2, 3 or 4 Misfire Detected

Trouble Code Conditions: Engine is running; atmospheric pressure, fuel level, battery voltage, engine speed, engine load are above minimal predetermined specifications; the engine is not in fuel cutoff and intake air temperature and coolant temperature are within normal operating ranges; there are no DTCs relating to ECT, CMP, CKP, MAP or IAT Sensor, to Crank rationality, to Crank Sensor Learn invalid, or to System Voltage. If total misfires detected are greater than 7% during the first 1000 rpm, or are over 3% after the first 1000 rpm, or are 25% during any 200 rpm with suspect cylinder misfire counter more than 80% and no other cylinder misfire counters above 80%, this DTC will set. The MIL will flash after first trip occurrence and will be steady after second trip.

Possible Causes:



Fuel system problems exist
 
Erratic CMP or CKP Sensor signals
 
Ignition system problems exist
 
Engine mechanical problems exist
 
PCM has failed
 

Trouble Code: P0302

Cylinder No. 1, 2, 3 or 4 Misfire Detected

Trouble Code Conditions: Engine is running; atmospheric pressure, fuel level, battery voltage, engine speed, engine load are above minimal predetermined specifications; the engine is not in fuel cutoff and intake air temperature and coolant temperature are within normal operating ranges; there are no DTCs relating to ECT, CMP, CKP, MAP or IAT Sensor, to Crank rationality, to Crank Sensor Learn invalid, or to System Voltage. If total misfires detected are greater than 7% during the first 1000 rpm, or are over 3% after the first 1000 rpm, or are 25% during any 200 rpm with suspect cylinder misfire counter more than 80% and no other cylinder misfire counters above 80%, this DTC will set. The MIL will flash after first trip occurrence and will be steady after second trip.

Possible Causes:



Fuel system problems exist
 
Erratic CMP or CKP Sensor signals
 
Ignition system problems exist
 
Engine mechanical problems exist
 
PCM has failed
 

Trouble Code: P0303

Cylinder No. 1, 2, 3 or 4 Misfire Detected

Trouble Code Conditions: Engine is running; atmospheric pressure, fuel level, battery voltage, engine speed, engine load are above minimal predetermined specifications; the engine is not in fuel cutoff and intake air temperature and coolant temperature are within normal operating ranges; there are no DTCs relating to ECT, CMP, CKP, MAP or IAT Sensor, to Crank rationality, to Crank Sensor Learn invalid, or to System Voltage. If total misfires detected are greater than 7% during the first 1000 rpm, or are over 3% after the first 1000 rpm, or are 25% during any 200 rpm with suspect cylinder misfire counter more than 80% and no other cylinder misfire counters above 80%, this DTC will set. The MIL will flash after first trip occurrence and will be steady after second trip.

Possible Causes:



Fuel system problems exist
 
Erratic CMP or CKP Sensor signals
 
Ignition system problems exist
 
Engine mechanical problems exist
 
PCM has failed
 

Trouble Code: P0304

Cylinder No. 1, 2, 3 or 4 Misfire Detected

Trouble Code Conditions: Engine is running; atmospheric pressure, fuel level, battery voltage, engine speed, engine load are above minimal predetermined specifications; the engine is not in fuel cutoff and intake air temperature and coolant temperature are within normal operating ranges; there are no DTCs relating to ECT, CMP, CKP, MAP or IAT Sensor, to Crank rationality, to Crank Sensor Learn invalid, or to System Voltage. If total misfires detected are greater than 7% during the first 1000 rpm, or are over 3% after the first 1000 rpm, or are 25% during any 200 rpm with suspect cylinder misfire counter more than 80% and no other cylinder misfire counters above 80%, this DTC will set. The MIL will flash after first trip occurrence and will be steady after second trip.

Possible Causes:



Fuel system problems exist
 
Erratic CMP or CKP Sensor signals
 
Ignition system problems exist
 
Engine mechanical problems exist
 
PCM has failed
 

Trouble Code: P0315

No Crankshaft Position Sensor Learned

Trouble Code Conditions: Engine started; engine runtime more than 50 seconds under closed throttle conditions; A/C off; ECT Sensor more than 167ºF (75C). The PCM detected that one of the CKP Sensor windows had too much variance (e.g., over 2.86%) from its calibrated reference point.

Possible Causes:



Crankshaft tone wheel flex plate is damaged
 
Tone wheel/pulse ring may be damaged
 
Erratic CKP Sensor signals (wiring/connector problem)
 
CKP Sensor has failed
 
PCM has failed
 

Trouble Code: P0325

Knock Sensor No. 1 Circuit

Trouble Code Conditions: Engine running at idle or in deceleration mode, and the PCM detected the Knock Sensor signal was below a minimum value (value depends on engine speed), or if Sensor voltage was about 5.0v with engine within idle range.

Possible Causes:



Knock Sensor connector is damaged or shorted
 
Knock Sensor signal circuit open or grounded
 
Knock Sensor signal circuit shorted to return circuit
 
Knock Sensor return circuit is open
 
Knock Sensor not tightened properly
 
Knock Sensor damaged or has failed (it may be open internally)
 
PCM has failed
 

Trouble Code: P0330

Knock Sensor No. 2 Circuit

Trouble Code Conditions: Engine running. The Knock Sensor circuit voltage falls below a minimum value at idle or deceleration. The minimum value is from a lookup table internal to the PCM and is based on engine rpm. This DTC will also set if the Sensor voltage goes above 5v. 3 good trips required to turn off MIL.

Possible Causes:



Knock Sensor No. 2 signal circuit shorted to battery voltage or to KS 2 return circuit
 
Knock Sensor No. 2 signal circuit or return circuit is open
 
Knock Sensor No. 2 signal circuit is shorted to KS 2 return circuit or to ground
 
Knock Sensor damaged or has failed
 
PCM has failed
 

Trouble Code: P0335

Crankshaft Position Sensor Circuit

Trouble Code Conditions: Engine cranking with at least 8 CMP Sensor signals detected. The PCM did not detect any CKP Sensor signals for 2 seconds.

Possible Causes:



Intermittent CKP signal
 
CKP Sensor signal circuit is open or it is shorted to ground or voltage
 
CKP Sensor 5v supply circuit is open or shorted to ground or voltage
 
CKP Sensor ground circuit is open
 
CKP Sensor or CMP Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0336

Crankshaft Position Sensor Incorrect Performance

Trouble Code Conditions: Engine running and no CMP Sensor DTCs are present. If the PCM detects an incorrect amount of CKP Sensor pulses when compared to CMP Sensor pulse, this DTC will set.

Possible Causes:



Intermittent CMP signal
 
Wiring harness problems exist
 
Tone wheel/pulse ring damaged or has failed
 
CKP Sensor is damaged or has failed
 
CMP Sensor has failed
 

Trouble Code: P0339

Crankshaft Position Sensor Circuit Intermittent

Trouble Code Conditions: Engine cranking or running; CMP Sensor signals detected. The PCM detected an intermittent loss of the CKP Sensor signal. The Failure counter must reach 20 before this code will set.

Possible Causes:



Check the tone wheel/pulse ring for damage or debris collection
 
CKP Sensor signal circuit is open or shorted to ground
 
CKP Sensor 5v supply circuit is open or shorted to ground
 
CKP Sensor is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0340

No Camshaft Position Sensor Circuit Failure

Trouble Code Conditions: Engine cranking or running, system voltage over 10v. The PCM detected CKP pulses without detecting any CMP Sensor pulses for 5 seconds or 2.5 engine revolutions.

Possible Causes:



CMP Sensor connector is damaged, open or it is shorted
 
CMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuit
 
CMP Sensor 5v supply circuit is open or shorted to ground or to battery voltage
 
CMP Sensor ground circuit is open
 
CMP Sensor is damaged or has failed
 
CKP Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0344

Camshaft Position Sensor Circuit Intermittent

Trouble Code Conditions: Engine cranking or running; system voltage over 10.5v. The PCM detected an intermittent loss of the CMP Sensor signal during the period of 2.5 complete engine revolutions. The failure counter must reach 20 before this code matures and a code is set.

Possible Causes:



Wiring harness fault
 
5v supply circuit open or shorted to ground
 
Tone wheel/pulse ring is damaged or corroded
 
CMP Sensor has failed
 
CMP Sensor signal circuit is open, shorted to ground or battery voltage or 5v supply
 
CMP Sensor ground circuit is open
 
PCM has failed
 

Trouble Code: P0401

EGR System Fault

Trouble Code Conditions: Engine running for more than 2 minutes with ECT more than 158ºF (70C). EGR is active. Vehicle is at less than 8500 feet altitude. Ambient temperature more than 20F (-6C). PCM closes EGR valve while monitoring O2 Sensor signal. Once a closed EGR fueling sample has been established, PCM then ramps in EGR and additional fueling, while monitoring the O2 Sensor signal in the open state. A fueling sample is again established. The PCM then compares the 2 different O2 Sensor signal readings (fueling samples). If a larger than expected variation is detected, a soft failure is recorded. Three soft failures set a one-trip (1T) failure. After 2 failed trips (2T), a DTC is set and the MIL illuminated.

Possible Causes:



EGR valve is open at idle
 
EGR solenoid ground circuit is open
 
EGR solenoid control circuit is open, shorted to ground or to voltage
 
ASD relay power circuit open to the EGR solenoid
 
EGR valve or solenoid is damaged or has failed
 
PCM has failed (EGR open or EGR closed)
 

Trouble Code: P0403

EGR Solenoid Circuit

Trouble Code Conditions: Engine started; system voltage over 10.5v. The EGR solenoid control circuit was not in its expected state when requested to operate by the PCM.

Possible Causes:



EGR solenoid ground circuit is open
 
EGR solenoid control circuit is open or shorted to ground or to voltage
 
EGR solenoid power circuit is open
 
EGR solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0404

EGR Position Sensor Signal Performance

Trouble Code Conditions: Engine started; system voltage over 10.5v and the PCM detected that the EGR flow (or valve movement) was not what was expected during the test period.

Possible Causes:



EGR Sensor signal circuit is open or shorted to ground
 
EGR Sensor 5v supply circuit is open or has high resistance
 
EGR Sensor ground circuit is open
 
EGR solenoid control circuit has a problem
 
EGR valve actuator loose, sticking, blocked or improperly grounded
 
EGR Sensor is damaged or has failed
 
Intermittent condition
 
PCM has failed
 

Trouble Code: P0405

EGR Position Sensor Circuit Low Input

Trouble Code Conditions: Key on or engine running; system voltage over 10v. The PCM detected that the EGR Sensor signal indicated less than 0.1v.

Possible Causes:



EGR Sensor signal circuit is shorted to ground or open
 
EGR Sensor VREF (5v) circuit is open or shorted to ground
 
EGR Sensor is damaged (shorted internally) or it has failed
 
EGR position internal failure
 
PCM has failed
 

Trouble Code: P0406

EGR Position Sensor Circuit High Input

Trouble Code Conditions: Key on or engine running; system voltage over 10.5v. The PCM detected the EGR Sensor indicated more than 4.89v for 6 seconds.

Possible Causes:



Intermittent condition
 
EGR Sensor signal is shorted to VREF (5v) supply circuit or to battery voltage
 
EGR Sensor ground circuit is open
 
EGR Sensor signal circuit is open
 
EGR Sensor is damaged (it may have an internal open circuit)
 
EGR solenoid failure
 
PCM has failed
 

Trouble Code: P0420

Catalyst Efficiency Below Normal (Bank 1)

Trouble Code Conditions: Engine speed at 1200-1700 rpm in closed loop with the throttle open for over 2 minutes, ECT Sensor more than 147ºF, MAP Sensor signal from 15.0-21.0 in. Hg, and the PCM detected the switch rate of the rear O2 reached 70% of the switch rate of the front O2.

Possible Causes:



Air leaks in at the exhaust manifold or exhaust pipes
 
Base engine problems (high coolant or engine oil consumption)
 
Catalytic converter damaged or has failed
 
Front O2 older (aged) than the rear O2 (O2 is lazy)
 

Trouble Code: P0430

Catalyst (2/1) Efficiency Below Normal

Trouble Code Conditions: After engine warm-up, ECT Sensor more than 170ºF for 180 seconds of open throttle operation and over 20 mph (engine between 1200-1700 rpm and MAP vacuum between 15-20 in. Hg). As catalyst efficiency deteriorates, the switch rate of the downstream O2 Sensor approaches that of the upstream O2 Sensor. If, at any point during the test, the switch ratio reaches a predetermined value, a counter is incremented by one. 3 good trips required to turn off MIL.

Possible Causes:



Exhaust leaks
 
Base engine problems
 
Catalytic converter damaged or has failed
 
Front O2 older (aged) than the rear O2 (O2 is lazy)
 

Trouble Code: P0432

Catalyst Efficiency Below Normal (Bank 2)

Trouble Code Conditions: Engine speed at 1200-1700 rpm in closed loop with the throttle open for over 2 minutes, ECT Sensor more than 147ºF, MAP Sensor signal from 15.0-21.0" Hg, and the PCM detected the switch rate of the rear O2 reached 70% of the switch rate of the front O2.

Possible Causes:



Air leaks in at the exhaust manifold or exhaust pipes
 
Base engine problems (high coolant or engine oil consumption)
 
Catalytic converter damaged or has failed
 
Front O2 older (aged) than the rear O2 (O2 is lazy)
 

Trouble Code: P0440

EVAP Purge System Fault

Trouble Code Conditions: Ambient Air Temperature from 39-89ºF (4-32C); engine running; Fuel level over 12%. The PCM detected that the NVLD switch did not close during medium/large leak test. Once this event occurs, the PCM will increase the amount of vacuum in the system that flows past the purge valve. If the NVLD switch does not close under these conditions, the PCM will set this code.

Possible Causes:



EVAP purge valve vacuum supply is leaking or clogged
 
EVAP purge valve is stuck closed
 
EVAP purge solenoid has failed
 
NVLD assembly (leak detection) is damaged or has failed
 
NVLD switch circuit is open or the NVLD switch has failed
 
Ground circuit is open
 
PCM has failed
 

Trouble Code: P0441

EVAP Purge Flow Monitor Fault

Trouble Code Conditions: Engine at idle speed in closed loop for 200 seconds, BARO Sensor signal less than 8,000 feet, ECT Sensor more than 160ºF, no Low Fuel, MAP Sensor signal less than 23.7" Hg, and the PCM did not detect any purge flow through the EVAP system during this test.

Possible Causes:



EVAP purge solenoid vacuum line loose, leaking or restricted
 
EVAP purge solenoid stuck leaking, stuck open or stuck closed
 
EVAP purge vacuum line to canister leaking or disconnected
 
EVAP canister leaking, damaged or has failed
 

Trouble Code: P0442

EVAP System Medium Leak Detected

Trouble Code Conditions: Monitor with engine running. Cold start test. Fuel level more than 12%. Ambient temperature between 39-89F (4-32C). Closed loop fuel system. Test runs when small leak test is maturing. The PCM activates EVAP purge solenoid to pull EVAP system into a vacuum to close the NVLD switch. Once this switch is closed, the PCM turns the EVAP purge solenoid off to seal the EVAP system. If the NVLD switch re-opens before the calibrated amount of time for a Medium leak, an error is detected.

Possible Causes:



Intermittent condition
 
Vacuum hoses, connections or switches have come loose or malfunctioned
 
EVAP emission system has a leak
 
EVAP purge solenoid operation has malfunctioned
 
NVLD switch operation has malfunctioned
 

Trouble Code: P0444

EVAP Purge Solenoid Circuit Open

Trouble Code Conditions: Any time key is on, if the PCM detects an open circuit in the purge solenoid or in the circuit for more than 280ms, a one-trip fault is set and the MIL is illuminated.

Possible Causes:



Intermittent condition
 
12v supply circuit is open
 
EVAP purge solenoid control circuit open
 
EVAP purge solenoid is open
 
PCM has failed
 

Trouble Code: P0452

NVLD Pressure Switch Sense Circuit Low Input

Trouble Code Conditions: Engine started; and immediately after the engine is running. The PCM activates the NVLD solenoid to test the NVLD switch circuit. If the switch is not open, the PCM sets this code.

Possible Causes:



EVAP purge solenoid control circuit is shorted to ground
 
EVAP purge solenoid is leaking or it is stuck in open position
 
NVLD assembly or NVLD switch is damaged or it has failed
 
NVLD switch signal circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P0453

NVLD Pressure Switch Sense Circuit High Input

Trouble Code Conditions: Engine started; and immediately after the engine is running, the PCM activates the NVLD solenoid to test the NVLD switch circuit. If the switch does not close under these conditions, this code is set.

Possible Causes:



NVLD assembly ground circuit is open
 
NVLD switch signal circuit is open or shorted to power (B+) or to NVLD solenoid control circuit
 
NVLD assembly or switch is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0455

EVAP Large Leak Detected

Trouble Code Conditions: Ambient Air Temperature from 39-89ºF at engine startup, engine running under closed loop conditions, Fuel Level over 12%, then with the EVAP purge solenoid enabled (to pull vacuum into the system to close the NVLD switch) and the EVAP "small leak" test maturing, the PCM turns "off" the EVAP purge solenoid once the NVLD switch closes. If the NVLD switch reopens before a calibrated amount of time expires, a "large" leak in the system is detected (larger than 0.080 in.).

Possible Causes:



EVAP purge solenoid is damaged or it has failed
 
Fuel tank cap is damaged, missing or the wrong part number
 
NVLD switch is damaged or it has failed
 

Trouble Code: P0456

EVAP System Small Leak Detected

Trouble Code Conditions: Ambient Air Temperature from 39-109ºF at engine startup, engine running under closed loop conditions, Fuel Level below 88%, then with the EVAP system sealed, the PCM monitors the NVLD switch. If the NVLD switch does not close within a calibrated amount of time expires, a "small" leak in the EVAP system was detected.

Possible Causes:



Fuel tank cap is damaged, loose or the wrong part number
 
Small leak present somewhere in the EVAP system
 

Trouble Code: P0458

EVAP Purge Solenoid Low Condition:

Trouble Code Conditions: Monitor with ignition on. If PCM detected an open in the purge solenoid of in the circuit for more than 280ms, a one-trip fault is set and the MIL is illuminated.

Possible Causes:



Intermittent condition
 
EVAP purge solenoid connector problems
 
EVAP purge solenoid control circuit is shorted to ground
 
EVAP purge solenoid leaks, stuck open, or stuck closed
 
PCM has failed
 

Trouble Code: P0459

EVAP Purge Solenoid High Condition:

Trouble Code Conditions: Monitor with ignition on. If PCM detected a short to ground in the purge solenoid of in the circuit for more than 280ms, a one-trip fault is set and the MIL is illuminated.

Possible Causes:



Intermittent condition
 
EVAP purge solenoid connector problems
 
EVAP purge solenoid control circuit is shorted to battery voltage
 
EVAP purge solenoid leaks, stuck open, or stuck closed
 
PCM has failed
 

Trouble Code: P0461

Fuel Level Sensor Malfunction

Trouble Code Conditions: With engine running and under partial load, the fuel level must be above 0%, and there must not be any fuel level Sensor electrical DTCs. If the PCM detects the fuel level change is less than 2% over 2 hours, this DTC will set.

Possible Causes:



Intermittent condition
 
Fuel tank or component damage
 
Fuel level Sensor signal circuit open or shorted to ground
 
Ground circuit is open
 
Fuel level Sensor malfunction
 

Trouble Code: P0462

Fuel Level Sending Unit Low Voltage

Trouble Code Conditions: Key on. If the PCM detects the fuel level as more than 100% for more than 4.5 minutes, this DTC will set.

Possible Causes:



Intermittent condition
 

Trouble Code: P0463

Fuel Level Sensor No. 1 High Input

Trouble Code Conditions: Key on. Battery voltage over 10.4v. If Fuel Level Sensor signal goes above 4.7v for more than 5 seconds (exc. Durango, Ram, Viper, Liberty), above 4.9v for more than 90 seconds (Durango, Ram, Viper, Liberty), this DTC is recorded.

Possible Causes:



Fuel level sending unit signal circuit is open or is shorted to battery voltage
 
Fuel level Sensor ground circuit is open
 
Fuel level Sensor is damaged or the fuel tank is damaged
 
Instrument cluster is faulty
 
BCM or PCM has failed
 

Trouble Code: P0480

Low Speed (No.1) Fan Control Relay Circuit

Trouble Code Conditions: Key on. Battery voltage over 10v. An open or shorted circuit is detected in the Low Speed Fan Relay control circuit system.

Possible Causes:



Fan relay intermittent condition
 
Ground circuit is open
 
Fused B+ output circuit malfunction
 
Fan relay control circuit is open or shorted to battery voltage or ground
 
Fan relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P0481

High Speed (No. 2) Fan Relay Control Circuit

Trouble Code Conditions: Key on or engine running; and the PCM detected an unexpected low or high voltage condition (open or shorted condition) on the High Speed Fan Relay circuit.

Possible Causes:



HFAN relay power circuit is open from the relay to fused power
 
HFAN relay control circuit is open or shorted to chassis ground
 
Fan relay(s) failed
 
PCM has failed.
 

Trouble Code: P0498

NVLD Canister Vent Solenoid Circuit Low

Trouble Code Conditions: Key on or engine running; and the PCM detected an unexpected low voltage condition on the Natural Vacuum Leak Detection (NVLD) control circuit during the CCM test period.

Possible Causes:



NVLD canister vent solenoid control circuit is shorted to ground
 
NVLD canister vent solenoid is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0499

NVLD Canister Vent Solenoid Circuit High

Trouble Code Conditions: Key on or engine running. The PCM detected an open or unexpected high voltage condition on the Natural Vacuum Leak Detection (NVLD) circuit.

Possible Causes:



NVLD canister vent solenoid control circuit is open or is shorted to power
 
NVLD canister vent solenoid ground circuit is open
 
NVLD canister vent solenoid is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0500

No Vehicle Speed Sensor Signal

Trouble Code Conditions: Engine started; if the PCM did not detect a VSS signal for over 6 seconds, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit open
 
VSS circuit is open or is shorted to ground
 
VSS ground circuit is open
 
VSS has failed
 
PCM has failed
 

Trouble Code: P0501

Vehicle Speed Sensor Performance

Trouble Code Conditions: Engine started; vehicle driven at over 1500 rpm for 10 seconds, gear selector not in Park or Neutral (or clutch is not depressed on M/T); brakes not applied. The PCM (or ECM: Liberty with Diesel) did not receive any VSS signals from the TCM (BCM: Liberty) for 11 seconds for 2 consecutive trips. 3 good trips required to turn off MIL.

Possible Causes:



Check for any ABS/RWAL or TCM codes related to the VSS
 
VSS connector is damaged, open or it is shorted
 
VSS signal is open, shorted to ground or shorted to power
 
Incorrect tire circumference
 
ABS/RWAL controller, BCM, ECM, TCM or PCM has failed
 

Trouble Code: P0503

Vehicle Speed Sensor No. 1 Erratic Performance

Trouble Code Conditions: Ignition is on; battery voltage over 10v; transmission in Drive or Reverse; brakes not applied. Vehicle speed signal is erratic during road load conditions. One-trip fault for ETC vehicles; Two-trip fault for ETC vehicles. 3 good trips required to turn off MIL.

Possible Causes:



Check for active Bus or Communication DTCs
 
Incorrect Tire Circumference
 
PCM has failed
 

Trouble Code: P0505

Idle Air Control Motor Circuit

Trouble Code Conditions: Engine started; system voltage over 11.5v and the PCM detected an unexpected voltage condition on one or more of the IAC motor circuits for 2.75 seconds (exc. Viper) or for 100ms (Viper), with the IAC motor active.

Possible Causes:



Stepper motor Coil No. 1, 2, 3 or 4 circuit open or shorted to ground
 
Stepper motor coil circuit(s) shorted to system power (B+)
 
Stepper motor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0507

Idle Speed High Performance Higher Than Expected

Trouble Code Conditions: Engine running at idle speed; MAF is less than 250 mg/tdc; air temperature is greater than 0F (-18C) and less than 19F (-7C) enable after coolant temperature is greater than 158F (70C) or air temperature is greater than 19F (-7C); coolant temperature is between 19 to 266F (-7 to 130C); canister purge is less than 100% duty cycle; no DTCs are present for VSS, MAF/MAP, ECT, TPS, ECT and CKP Sensors; also no fuel system or injector related DTCs are present. If the DTC detects that engine speed is 200 rpm or more above the normal idle speed for 7 seconds, this DTC will set.

Possible Causes:



Air induction system restrictions (clogged air filter, etc.)
 
Vacuum leaks
 
Intermittent condition
 
Throttle body or linkage is binding, damaged or sticking
 
PCM has failed
 

Trouble Code: P0508

Idle Air Control Motor Sense Circuit Low Input

Trouble Code Conditions: Engine started; system voltage over 10.5v; IAC motor operating. The PCM detected the IAC Motor Sense circuit current was less than 175mA during the CCM test period.

Possible Causes:



IAC motor driver circuit is open or shorted to ground
 
IAC motor sense circuit is open or shorted to ground
 
IAC motor is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0509

Idle Air Control Motor Circuit High

Trouble Code Conditions: Engine started; system voltage over 10.5v, IAC motor activated, and the PCM detected a high voltage on one or more of the IAC motor circuits (over 980mA) during the CCM test period.

Possible Causes:



IAC motor driver circuit is shorted to power
 
IAC motor sense circuit is shorted to power
 
IAC motor is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0513

Invalid SKIM Key Detected

Trouble Code Conditions: Key on, and the PCM detected an invalid Sentry Key Immobilizer key had been inserted into the ignition key assembly.

Possible Causes:



Incorrect VIN in the PCM
 
No communication between the PCM and the SKIM
 
SKIM trouble codes present (check for any SKIM codes)
 
Valid SKIM key not present
 
VIN not programmed into the PCM
 
PCM has failed
 

Trouble Code: P0516

Battery Temperature Sensor Circuit Low Input

Trouble Code Conditions: Key on or engine running; and the PCM detected a Battery Temperature Sensor signal that indicated less than 0.10v (exc. Ram, Liberty) or less than 0.039v (Ram, Liberty). 3 good trips required to turn off MIL.

Possible Causes:



BTS signal circuit is shorted to Sensor or chassis ground
 
BTS assembly is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0517

Battery Temperature Sensor Circuit High Input

Trouble Code Conditions: Key on or engine running; and the PCM detected a Battery Temperature Sensor signal that indicated more than 4.8v (exc. Ram, Liberty) or more than 4.94v (Ram, Liberty).

Possible Causes:



BTS signal circuit is shorted to VREF (5v)
 
BTS signal circuit is open or the BTS ground circuit is open
 
BTS assembly is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0520

Engine Oil Pressure Sensor Out of Range

Trouble Code Conditions: Key on (engine not started). The PCM detected an engine oil pressure reading out of the calibrated range.

Possible Causes:



Oil pressure Sensor signal circuit is open or shorted to ground
 
Oil pressure Sensor signal circuit has high resistance
 
5v supply circuit has high resistance
 
5v supply circuit is shorted to ground
 
Oil pressure Sensor ground circuit has high resistance
 
Oil pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0521

Engine Oil Pressure Sensor Does Not Reach Range

Trouble Code Conditions: Engine running. The PCM detected an engine oil pressure reading never reaches the calibrated specification when engine is at 1250 rpm.

Possible Causes:



Engine oil or engine mechanical fault
 
Oil pressure Sensor signal circuit is shorted to battery
 
Oil pressure Sensor signal circuit has high resistance
 
5v supply circuit has high resistance
 
5v supply circuit is shorted to ground
 
Oil pressure Sensor return circuit has high resistance
 
Oil pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0522

Engine Oil Pressure Sensor Rationality

Trouble Code Conditions: Engine running; battery voltage over 10.4v. If the PCM detected an engine oil pressure voltage reading of less than 0.1v for 0.5 second (Neon, Dakota, Durango, Ram), less than 0.3v (Viper), or less that 0.942v (Liberty), this DTC will set.

Possible Causes:



5v supply circuit is open or is shorted to ground
 
Oil pressure Sensor signal circuit is shorted to ground or to sensor ground
 
Oil pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0523

Engine Oil Pressure Sensor Circuit High

Trouble Code Conditions: Key on (engine not started). The PCM detected an engine oil pressure reading greater than the calibrated amount.

Possible Causes:



Oil pressure Sensor signal circuit is open or shorted to battery voltage or to 5v supply circuit
 
Oil pressure Sensor ground circuit is open
 
Oil pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0524

Engine Oil Pressure Low

Trouble Code Conditions: Engine running. The PCM detected that the engine oil pressure never reaches the calibrated specification to allow the MDS activation.

Possible Causes:



Engine oil system or engine mechanical faults
 
Oil pressure Sensor signal circuit is shorted to battery voltage or to ground
 
Oil pressure Sensor signal circuit has high resistance
 
5v supply circuit has high resistance
 
5v supply circuit is shorted to ground
 
Oil pressure Sensor return circuit has high resistance
 
Oil pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0532

Air Conditioning Pressure Sensor Circuit Low Input

Trouble Code Conditions: Engine running with the A/C relay energized. The PCM detected the signal from the A/C Pressure Sensor indicated less than 0.58v for over 2.6 seconds during the CCM test period.

Possible Causes:



A/C pressure Sensor 5v power supply (VREF) circuit is open or is shorted to ground
 
A/C pressure Sensor signal circuit is shorted to ground or to Sensor ground circuit
 
A/C pressure Sensor is damaged or it has failed
 
Front A/C control module damaged or has failed
 
PCM has failed
 

Trouble Code: P0533

Air Conditioning Pressure Sensor Circuit High Input

Trouble Code Conditions: Engine running with the A/C relay energized, and the PCM detected the signal from the A/C Pressure Sensor indicated less than 4.92v for over 2.6 seconds during the CCM test period.

Possible Causes:



A/C pressure Sensor signal circuit is shorted to 5v VREF power
 
A/C pressure Sensor signal circuit or ground circuit is open
 
A/C pressure Sensor is damaged or it has failed
 
Front A/C control module is damaged or has failed
 
PCM has failed
 

Trouble Code: P0551

Power Steering Pressure Switch Circuit Failure

Trouble Code Conditions: Engine running and vehicle driven at more than 30 mph for 60 seconds; no VSS DTC is present. If the PCM detected the PSPS signal remains high after 60 seconds, this DTC will set.

Possible Causes:



PSPS sense circuit is open or is shorted to ground
 
PSPS ground circuit is open
 
PSPS is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0562

Charging System Voltage Low

Trouble Code Conditions: PCM: Engine is running for over 30 sec. If the PCM detects battery voltage is under 11.5v for more than 5 sec., this DTC will set. Other charging system DTCs may be present. TCM w/NGC: Engine is running and PCM has closed the Transmission Control Relay. If battery voltage of the TC Relay output sense circuit is less than 10v for 15 seconds, this DTC will set. Note: P0562 usually indicates failing battery voltage or resistive connection to the PCM. This DTC also sets if battery voltage sensed at PCM is less than 6.5v for 200ms or when the TC Relay output circuit is less than 7.2v for 200ms.

Possible Causes:



Resistance is high in battery positive circuit or in generator case ground
 
Ground circuit is open or has high resistance
 
Fused B+ circuit to TC relay or to PCM has high resistance
 
Intermittent wiring or connector condition
 
TC relay output to TCM is open or has high resistance
 
TC relay has failed
 
Generator field driver circuit is open
 
ASD relay output circuit is open
 
Generator has failed
 
PCM has failed
 

Trouble Code: P0563

Battery Sense Circuit High Input

Trouble Code Conditions: Engine running at a speed over 380 rpm, and the PCM detected the Battery Sense circuit voltage indicated 1v higher than the Charging system "goal" during the CCM test.

Possible Causes:



Generator field control circuit is shorted to system power (B+)
 
Generator is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0571

Brake Switch No. 1 No Output Signal

Trouble Code Conditions: Ignition is on. If output of BS 1 to PCM looks like brake is not applied, while BS 2 circuit is applied, the fault will mature in 60ms.

Possible Causes:



BS 1 signal open or shorted to ground
 
BS 2 signal open or shorted to ground
 
Ground circuit is open
 
Fused ignition switch output is open
 
Stop lamp switch is damaged or has failed
 
PCM has failed
 

Trouble Code: P0572

Brake Switch Circuit Low

Trouble Code Conditions: Engine is running and vehicle speed is above 31 mph; battery voltage is more than 9.5v; no other brake switch DTCs are present. If the PCM detects no change from the brake switch sense circuit input after coming to a complete stop, it will increment a counter. If the counter increments 10 times, the DTC will set and the MIL will illuminate.

Possible Causes:



Intermittent condition
 
Fused B+ circuit problem
 
Brake switch sense circuit is shorted to ground
 
Brake switch is closed
 
PCM has failed
 

Trouble Code: P0573

Brake Switch Circuit High

Trouble Code Conditions: Engine is running and vehicle speed is above 31 mph; accelerator pedal position is more than 25%; battery voltage is more than 9.5v; no other brake switch DTCs are present. If the PCM detects a high brake switch sense circuit input, it will increment a counter. If the counter increments 10 times, the DTC will set and the MIL will illuminate.

Possible Causes:



Intermittent condition
 
Fused B+ circuit problem
 
Brake switch sense circuit is open or is shorted to voltage
 
Ground circuit is open
 
Brake switch lamp operation has failed
 
PCM has failed
 

Trouble Code: P0580

Speed Control Switch No. 1 Circuit Low Input

Trouble Code Conditions: Key on or engine started; system voltage over 10.0v and the PCM detected the Speed Control Switch No. 1 signal indicated less than 0.43v (exc. Liberty) or 0.60v (Liberty) for 2 minutes. 3 good trips required to turn off MIL.

Possible Causes:



Intermittent condition
 
S/C switch signal circuit is shorted to chassis or Sensor ground
 
S/C On/Off switch is damaged or it has failed
 
S/C Resume/Accel switch is damaged or it has failed
 
PCM has failed.
 

Trouble Code: P0581

Speed Control Switch No. 1 Circuit High Input

Trouble Code Conditions: Engine started; system voltage over 10v and the PCM detected an open or shorted condition, or above maximum acceptable S/C switch voltage, in the Speed Control Switch signal circuit.

Possible Causes:



S/C switch No.1 signal circuit is shorted to system power (B+)
 
S/C switch ground circuit is open
 
S/C switch signal circuit is open between PCM and clockspring
 
S/C Sensor ground circuit is open between PCM and clockspring or clockspring and S/C switch
 
Clockspring has failed
 
S/C switch (one or more) is damaged or has failed
 
PCM has failed
 

Trouble Code: P0582

Speed Control Vacuum Solenoid Circuit Malfunction

Trouble Code Conditions: Ignition on or engine started; Speed Control (S/C) system activated, and the PCM detected an open or short to voltage condition on the S/C Vacuum solenoid circuit during the CCM test period.

Possible Causes:



S/C supply circuit is open or is short to ground or to battery voltage
 
S/C vacuum solenoid control circuit is open
 
S/C vacuum solenoid control circuit is shorted to ground
 
S/C vacuum solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0586

Speed Control Vent Solenoid Circuit Malfunction

Trouble Code Conditions: Engine started; battery voltage over 10v; Speed Control (S/C) system activated. The PCM detected an unexpected voltage condition on the S/C Vent solenoid circuit during the CCM test period.

Possible Causes:



S/C supply circuit is open or is short to ground
 
S/C vent solenoid control circuit is open
 
S/C vent solenoid control circuit is shorted to ground
 
S/C vent solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0594

Speed Control Servo Power Circuit Malfunction

Trouble Code Conditions: Engine started; Speed Control (S/C) system activated. The PCM detected an unexpected voltage condition on the S/C Vent solenoid circuit during the CCM test period.

Possible Causes:



S/C solenoid or vent solenoid has failed
 
Brake switch is damaged or it has failed
 
S/C brake switch circuit is open or it is shorted to ground
 
S/C power circuit is open or it is shorted to ground
 
PCM has failed
 

Trouble Code: P0600

Serial Communication Link Malfunction

Trouble Code Conditions: Ignition on. Internal Bus communication failure is recognized between engine and transmission processors.

Possible Causes:



PCM or SPI failure
 

Trouble Code: P0601

PCM Internal Controller Failure

Trouble Code Conditions: Ignition on. Internal CHECKSUM (or Bus communication) for software has failed; no communication between processors; cannot match calculated value.

Possible Causes:



PCM or SPI failure
 

Trouble Code: P0602

Control Module Programming Error

Trouble Code Conditions: Condition is monitored continuously. This DTC will always illuminate the MIL and is designed to signal the technician that the controller still has generic software installed.

Possible Causes:



Control module needs updated programming
 

Trouble Code: P0604

Internal TCM Error

Trouble Code Conditions: Condition is monitored continuously. This DTC will always illuminate the MIL and is designed to signal the technician that there is a PCM internal error.

Possible Causes:



PCM needs to be replaced, and then reprogrammed
 

Trouble Code: P0605

Internal TCM Error

Trouble Code Conditions: Condition is monitored continuously. This DTC will always illuminate the MIL and is designed to signal the technician that there is a PCM internal error.

Possible Causes:



PCM needs to be replaced, and then reprogrammed
 

Trouble Code: P0613

Internal TCM Error

Trouble Code Conditions: Condition is monitored continuously. This DTC will always illuminate the MIL and is designed to signal the technician that there is a PCM internal error.

Possible Causes:



PCM needs to be replaced, and then reprogrammed
 

Trouble Code: P0622

Generator Field Control Circuit Malfunction

Trouble Code Conditions: Engine running. The PCM detected the Generator Field control circuit had malfunctioned (PCM tries to regulate the generator field with no result).

Possible Causes:



Generator field control circuit is open or is shorted to ground
 
Generator field control circuit is shorted to system power (B+)
 
Generator field ground circuit is open
 
Generator is damaged or PCM has failed
 
PCM has failed
 

Trouble Code: P0625

Generator Field Control Circuit Low

Trouble Code Conditions: Engine running for more than 25 seconds. The PCM detected the Generator Field circuit is open or is shorted to ground.

Possible Causes:



Wiring harness intermittent problem
 
Generator field driver circuit is open or is shorted to ground
 
Generator field has malfunctioned
 
Generator field coil is open
 
PCM has failed
 

Trouble Code: P0626

Generator Field Control Circuit High

Trouble Code Conditions: Engine running for more than 25 seconds. The PCM detected the Generator Field circuit is shorted B+.

Possible Causes:



Wiring harness intermittent problem
 
Generator field circuit is shorted to voltage
 
Generator has malfunctioned
 

Trouble Code: P0627

Fuel Pump Relay Control Circuit Malfunction

Trouble Code Conditions: Engine started; system voltage over 10.5v. The PCM detected an unexpected voltage condition (open or short) on the Fuel Pump relay control circuit during the CCM test period.

Possible Causes:



Fuel pump relay control circuit is open or is shorted to ground
 
Fuel pump relay control circuit is shorted to system power (B+)
 
Fuel pump relay power circuit (fused ignition) circuit is open
 
Fuel pump relay is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0628

Fuel Pump Relay Control Circuit Low

Trouble Code Conditions: Ignition is on. If the PCM detects no voltage on the fuel pump relay control circuit for more than 3 seconds, this DTC will set.

Possible Causes:



Fuel pump relay intermittent operation
 
Fuel system/circuit intermittent operation
 
Fused ignition switch output circuit problem
 
Fuel pump relay has failed
 
Fuel pump relay control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P0629

Fuel Pump Relay Control Circuit High

Trouble Code Conditions: Ignition is on. If the PCM detects high voltage on the fuel pump relay control circuit for more than 3 seconds, this DTC will set.

Possible Causes:



Fuel pump relay intermittent operation
 
Fuel system/circuit intermittent operation
 
Fuel pump relay has failed
 
Fuel pump relay control circuit is shorted to battery voltage
 
PCM has failed
 

Trouble Code: P0630

VIN Not Programmed Into The PCM

Trouble Code Conditions: Key on, and the PCM determined that the Vehicle Identification Number (VIN) had not been programmed into its memory.

Possible Causes:



Reprogram the correct VIN into the PCM
 
PCM has failed
 

Trouble Code: P0632

Odometer Not Programmed Into The PCM

Trouble Code Conditions: Key on, and the PCM detected the vehicle mileage had not been programmed into memory.

Possible Causes:



Reprogram the correct mileage into the PCM
 
PCM has failed
 

Trouble Code: P0633

SKIM Key Not Programmed Into The PCM

Trouble Code Conditions: Key on, and the PCM determined that the Security Key Immobilizer (SKIM) information had not been programmed into its memory.

Possible Causes:



Reprogram the SKIM key into the PCM
 
PCM has failed
 

Trouble Code: P0645

A/C Clutch Relay Circuit Malfunction

Trouble Code Conditions: Engine started; system voltage over 10.0v, A/C switch "on". The PCM detected an unexpected voltage condition (open or shorted condition) on the A/C Clutch relay control circuit during the CCM test.

Possible Causes:



Internally fused ignition switch output circuit is faulty
 
A/C relay clutch control circuit is open or it is shorted to ground
 
A/C relay clutch power supply (fused ignition) circuit is open
 
A/C relay is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0646

A/C Clutch Relay Control Circuit Low

Trouble Code Conditions: Ignition is on. If the PCM detects low voltage on the A/C clutch relay control circuit for more than 2.73 seconds, this DTC will set.

Possible Causes:



A/C relay intermittent operation
 
Fused B+ circuit problem
 
A/C clutch relay has failed
 
A/C clutch relay control circuit is open or is shorted to ground
 
PCM has failed
 

Trouble Code: P0647

A/C Clutch Relay Control Circuit High

Trouble Code Conditions: Ignition is on. If the PCM detects high voltage on the A/C clutch relay control circuit for more than 2.73 seconds, this DTC will set.

Possible Causes:



A/C relay intermittent operation
 
A/C system intermittent condition
 
A/C clutch relay has failed
 
A/C clutch relay control circuit is shorted to battery voltage
 
PCM has failed
 

Trouble Code: P0660

Manifold Tune Valve Solenoid Circuit Malfunction

Trouble Code Conditions: Engine started; ASD relay "on", system voltage over 10.0v, and the PCM detected an unexpected voltage condition on the Manifold Tune Valve (MTV) solenoid control circuit.

Possible Causes:



Fused B+ circuit has failed
 
MTV solenoid/relay circuit is open or it is shorted to ground
 
MTV solenoid/relay circuit is shorted to power
 
MTV solenoid/relay ground circuit is open
 
MTV solenoid/relay is damaged or it has failed
 
PCM has failed
 

Trouble Code: P0685

ASD Relay Control Circuit Malfunction

Trouble Code Conditions: Key on; system voltage over 10.0v. The PCM detected an unexpected voltage condition (open or short) on the Automatic Shutdown (ASD) relay control circuit during the CCM test period (ASD actual state is not equal to the desired state). 3 good trips are required to turn off MIL. P0688 may also set.

Possible Causes:



Fused B+ circuit faults
 
ASD relay connector is damaged, loose or shorted
 
ASD relay control circuit is open or it is shorted to ground
 
ASD power supply (fused B+) circuit is open
 
ASD relay is damaged, has high resistance, or it has failed
 
PCM has failed
 

Trouble Code: P0686

ASD Relay Control Circuit Low

Trouble Code Conditions: Ignition is on. If the PCM detects no voltage on the ASD relay control circuit for more than 3.5 seconds, this DTC will set.

Possible Causes:



ASD relay intermittent operation
 
ASD system intermittent condition
 
Fused B+ circuit problem
 
ASD relay has failed
 
ASD relay control circuit is open or is shorted to ground
 
PCM has failed
 

Trouble Code: P0687

ASD Relay Control Circuit High

Trouble Code Conditions: Ignition is on. If the PCM detects high voltage on the ASD relay control circuit for more than 3.5 seconds, this DTC will set.

Possible Causes:



ASD relay intermittent operation
 
ASD system intermittent condition
 
ASD relay has failed
 
ASD relay control circuit is shorted to battery voltage
 
PCM has failed
 

Trouble Code: P0688

ASD Relay Sense Circuit Low

Trouble Code Conditions: Key on, ASD relay energized, system voltage over 10.0v, and the PCM did not detect any voltage on the Automatic Shutdown (ASD) Sense circuit during the CCM test period.

Possible Causes:



ASD relay output circuit is open
 
ASD power supply (fused B+) circuit is open
 
ASD relay is damaged or it has failed
 
Problem in fuse/relay center
 
PCM no start condition
 
PCM has failed
 

Trouble Code: P0690

ASD Relay Sense Circuit High

Trouble Code Conditions: Key on, ASD relay energized, system voltage over 10.0v, and the PCM (PT Cruiser) or FCM (Durango) detects high voltage on the Automatic Shutdown (ASD) Sense circuit during the CCM test period.

Possible Causes:



Intermittent condition
 
ASD relay output circuit is shorted to voltage
 
ASD relay is damaged or it has failed
 
PCM internal short to voltage
 
PCM has failed
 

Trouble Code: P0691

Low Speed Fan (Fan No. 1) Relay Control Circuit Low

Trouble Code Conditions: Key on; No. 1 cooling fan relay is actuated. If the PCM (PT Cruiser) or FCM (Durango) detects no voltage (open or shorted to ground) on the Radiator Fan Relay control circuit for more than 3 seconds, this DTC will set.

Possible Causes:



Intermittent condition
 
Fused ignition switch output circuit problems
 
Radiator fan relay has failed
 
Radiator fan control circuit is open or is shorted to ground
 
PCM has failed
 

Trouble Code: P0692

Low Speed Fan (Fan No. 1) Relay Control Circuit High

Trouble Code Conditions: Key on; radiator fan commanded ON. If the PCM (PT Cruiser) or FCM (Durango) detects an open or high voltage on the Radiator Fan Relay circuit for more than 3 seconds, this DTC will set.

Possible Causes:



Intermittent condition
 
Radiator fan relay has failed
 
Radiator fan control circuit is shorted to battery voltage
 
PCM has failed
 

Trouble Code: P0693

High Speed Fan (Fan No. 2) Relay Control Circuit Low

Trouble Code Conditions: Key on; fan relay is powered on. If the PCM (PT Cruiser) or FCM (Durango) detects no voltage (open or shorted) on the Radiator Fan Relay control circuit for more than 3 seconds, this DTC will set. Circuit is continuously monitored.

Possible Causes:



Intermittent condition
 
Fused ignition switch output circuit problems
 
Radiator fan relay has failed
 
Radiator fan control circuit is open or is shorted to ground
 
PCM has failed
 

Trouble Code: P0694

High Speed Fan (Fan No. 2) Relay Control Circuit High

Trouble Code Conditions: Key on; radiator fan commanded ON. If the PCM (PT Cruiser) or FCM (Durango) detects an open, short or high voltage on the Radiator Fan Relay circuit for more than 3 seconds, this DTC will set. This circuit is continuously monitored.

Possible Causes:



Intermittent condition
 
Radiator fan relay has failed
 
Radiator fan control circuit is open or shorted to battery voltage
 
PCM has failed
 

Trouble Code: P0700

Automatic Transmission Control System Malfunction

Trouble Code Conditions: Ignition on or engine started. The PCM received a message over the CCD Bus from the Transmission Control Module (TCM) that it had detected a problem and set a trouble code in memory.

Possible Causes:



The presence of this code means the TCM detected a problem
 
TCM related Sensor has solenoid is damaged or has failed
 
This code is for information only - check for other TCM codes
 
TCM or PCM has failed
 

Trouble Code: P0703

Brake Lamp Switch No. 2 Performance Malfunction

Trouble Code Conditions: Engine is running; battery voltage is more than 9.5v; no other brake switch DTCs are present. When Brake Switch 1 output is the same as Brake Switch No. 2 output for more than 25 seconds, this DTC will set.

Possible Causes:



Intermittent condition
 
Fused B+ circuit malfunction
 
Brake switch output circuit is open or is shorted to battery voltage or to ground
 
Ground circuit is open
 
Brake switch or PCM has failed
 

Trouble Code: P0706

A/T Check Shifter Signal Circuit Malfunction

Trouble Code Conditions: Key on. After 3 occurrences in one ignition cycle of an invalid PRNDL DDTC which last for more than 0.1 second. NOTE: All indicator lights on the instrument cluster will illuminate boxed when the vehicle engine is not running, ignition on, or engine running in Park or Neutral if a problem exists.

Possible Causes:



Shifter out of adjustment
 
TRS T1, T3, T41 or T42 sense circuit is open, shorted to ground or to voltage
 
TRS Sensor has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0711

A/T Transmission Fluid Temperature Sensor Signal - No Rise After Startup

Trouble Code Conditions: Engine started. This DTC will set when the desired transmission temperature does not reach a normal operation temperature within a given time frame. Time is variable due to ambient temperature at cold engine start: from 35 minutes at 40F (-40C) to 10 minutes at 60F (15C).

Possible Causes:



Related DTCs will be present
 
Transmission temperature Sensor has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0712

A/T Transmission Fluid Temperature Sensor Low Input

Trouble Code Conditions: Engine started and the PCM detected the TFT Sensor signal was under 0.078v for 0.45 second.

Possible Causes:



Related DTCs are present
 
TFT Sensor signal circuit is shorted to ground
 
TFT Sensor is damaged or has failed (it may be shorted)
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0713

A/T Transmission Fluid Temperature Sensor High Input

Trouble Code Conditions: Engine started and the PCM detected the TFT Sensor signal was over 4.94v for 0.45 second.

Possible Causes:



Related DTCs are present
 
TFT Sensor signal circuit is open or is shorted to voltage
 
TFT Sensor is damaged or has failed (it may be shorted)
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0714

A/T Transmission Fluid Temperature Sensor Intermittent

Trouble Code Conditions: Engine started and the PCM detected the TFT Sensor signal was fluctuating or changes abruptly within a predetermined period of time.

Possible Causes:



Related DTCs are present
 
TFT Sensor is damaged or has failed (it may be shorted)
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0715

TCM Input Speed Sensor Circuit Malfunction

Trouble Code Conditions: Engine started; the transmission gear ratio is monitored continuously while the transmission is in gear. This DTC will set if there is an excessive change in the Input RPM in any gear.

Possible Causes:



ISS ground circuit is open or is shorted to voltage
 
ISS signal circuit is open, shorted to ground or to power
 
ISS Sensor is damaged or it has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0719

Brake Lamp Switch Circuit Low

Trouble Code Conditions: Vehicle is driven over 31 mph; battery over 9.5v. If the PCM detects no change from Brake Lamp Switch circuit input, after a complete stop, it will increment a counter. If the counter increments 10 times, this DTC will set and the MIL will illuminate.

Possible Causes:



Intermittent condition
 
Fused B+ circuit problems
 
Brake lamp switch sense circuit is open or is shorted to ground
 
Ground circuit is open
 
Brake lamp switch has failed
 
PCM has failed
 

Trouble Code: P0720

TCM Output Speed Sensor Circuit Malfunction

Trouble Code Conditions: Engine started; the transmission gear ratio is monitored continuously while the transmission is in gear. This DTC will set if there is an excessive change in the Output RPM in any gear. On some models, this DTC can take up to 5 minutes of problem identification before lighting the MIL.

Possible Causes:



OSS ground circuit is open or is shorted to voltage or to ground
 
Speed Sensor ground circuit is open, shorted to ground or to voltage
 
OSS Sensor is damaged or it has failed
 
Intermittent wiring or connector problems
 
PCM or TCM has failed
 

Trouble Code: P0724

Brake Lamp Switch Circuit High

Trouble Code Conditions: Vehicle is driven at speeds over 31 mph; accelerator pedal position is more than 25%; battery voltage over 9.5v. If the PCM detects a high Brake Lamp Switch circuit input, it will increment a counter. If the counter increments 10 times, this DTC will set and the MIL will illuminate.

Possible Causes:



Intermittent condition
 
Brake lamp switch sense circuit is shorted to battery voltage
 
Brake lamp switch has failed
 
PCM has failed
 

Trouble Code: P0725

A/T Engine Speed Sensor Circuit Malfunction

Trouble Code Conditions: Engine running; and the PCM detected an Engine Speed Sensor reading of less than 390 rpm or more than 8000 rpm occurred for 2 seconds during the CCM test.

Possible Causes:



Check for trouble codes related to the CKP Sensor
 
CKP Sensor signal circuit open, shorted to ground or to power
 
CKP Sensor is damaged or has failed (open or shorted)
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0731

A/T Additional Gear Ratio Error In First Gear

Trouble Code Conditions: The transmission gear ratio is monitored continuously while the transmission is in gear. If the ratio of the Input RPM to the Output RPM does not match the current gear ratio, this DTC will set.

Possible Causes:



Related DTCs will be present
 
Internal transmission mechanical problems may exist
 
Intermittent gear ratio errors are present
 

Trouble Code: P0732

A/T Additional Gear Ratio Error In Second Gear

Trouble Code Conditions: The transmission gear ratio is monitored continuously while the transmission is in gear. If the ratio of the Input RPM to the Output RPM does not match the current gear ratio, this DTC will set.

Possible Causes:



Related DTCs will be present
 
Transmission solenoid/pressure switch assembly has malfunctioned or failed
 
Internal transmission mechanical problems may exist
 
Intermittent gear ratio errors are present
 

Trouble Code: P0733

A/T Additional Gear Ratio Error In Third Gear

Trouble Code Conditions: The transmission gear ratio is monitored continuously while the transmission is in gear. If the ratio of the Input RPM to the Output RPM does not match the current gear ratio, this DTC will set.

Possible Causes:



Related DTCs will be present
 
Transmission solenoid/pressure switch assembly has malfunctioned or failed
 
Internal transmission mechanical problems may exist
 
Intermittent gear ratio errors are present
 

Trouble Code: P0734

A/T Additional Gear Ratio Error In Fourth Gear

Trouble Code Conditions: The transmission gear ratio is monitored continuously while the transmission is in gear. If the ratio of the Input RPM to the Output RPM does not match the current gear ratio, this DTC will set.

Possible Causes:



Related DTCs will be present
 
Transmission solenoid/pressure switch assembly has malfunctioned or failed
 
Internal transmission mechanical problems may exist
 
Intermittent gear ratio errors are present
 

Trouble Code: P0735

A/T Gear Ratio Error Fourth Prime

Trouble Code Conditions: Vehicle driven any forward Gear, and the TCM detected the ratio of the Input speed to the Output Speed did not match the current Gear Ratio (this test can take up to 5 minutes).

Possible Causes:



Related Gear Ratio trouble codes may be stored (note that some of these Gear Ratio trouble codes may be intermittent)
 
Transmission has internal problems or damage present
 

Trouble Code: P0736

A/T Additional Gear Ratio Error In Reverse Gear

Trouble Code Conditions: The transmission gear ratio is monitored continuously while the transmission is in gear. If the ratio of the Input RPM to the Output RPM does not match the current gear ratio, this DTC will set.

Possible Causes:



Related DTCs will be present
 
Internal transmission mechanical problems may exist
 
Intermittent gear ratio errors are present
 

Trouble Code: P0740

A/T Torque Converter Clutch System Out of Range

Trouble Code Conditions: The TCC is in FEMCC or PEMCC, transmission temperature is hot, engine temperature is more than 100F (38C), transmission input speed is more than 1750 rpm, with TPS less than 30. The TCC is modulated by controlling the duty cycle of the L/R solenoid, until the difference between the engine and transmission input speed rpm or duty cycle is within desired range. The DTC is set after the period of 10 seconds and 3 occurrences of either: FEMCC with slip greater than 100 rpm or PEMCC duty cycle is more than 85%.

Possible Causes:



Related DTCs will be present
 
Internal transmission mechanical problems may exist
 
Intermittent gear ratio errors are present
 

Trouble Code: P0750

A/T Low/Reverse Solenoid Circuit Failure

Trouble Code Conditions: Solenoids are tested initially at power-up, then every 10 seconds thereafter, the solenoids will also be tested immediately after a gear ratio or pressure switch error is detected. 3 consecutive solenoid continuity test failures, or one failure if test is run in response to a gear ratio or pressure switch error.

Possible Causes:



Related relay DTCs present
 
Transmission control relay output circuit open
 
L/R solenoid control circuit open or shorted to ground or to voltage
 
L/R solenoid/pressure switch assembly has malfunctioned or failed
 
Intermittent wiring and connectors
 
PCM has failed
 

Trouble Code: P0755

A/T 2/4 Solenoid Circuit Failure

Trouble Code Conditions: 2/4 solenoid in monitored initially at power-up, then every 10 seconds thereafter. Also, immediately after a gear ratio or pressure switch error is detected. 3 consecutive solenoid continuity test failures, or one failure if test is run in response to a gear ratio or pressure switch error.

Possible Causes:



Related DTCs present
 
Transmission control relay output circuit open
 
2/4 Solenoid control circuit is open or shorted to ground
 
2/4 Solenoid control circuit is shorted to system power
 
2/4 Solenoid is damaged or has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0760

A/T Overdrive Solenoid Circuit Failure

Trouble Code Conditions: O/D solenoid in monitored initially at power-up, then every 10 seconds thereafter. Also, immediately after a gear ratio or pressure switch error is detected. 3 consecutive solenoid continuity test failures, or one failure if test is run in response to a gear ratio or pressure switch error.

Possible Causes:



Related DTCs present
 
Transmission control relay output circuit open
 
O/D Solenoid control circuit is open or shorted to ground
 
O/D Solenoid control circuit is shorted to system power
 
O/D Solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0765

A/T Underdrive Solenoid Circuit Failure

Trouble Code Conditions: U/D solenoid in monitored initially at power-up, then every 10 seconds thereafter. Also, immediately after a gear ratio or pressure switch error is detected. 3 consecutive solenoid continuity test failures, or one failure if test is run in response to a gear ratio or pressure switch error.

Possible Causes:



Related DTCs present
 
Transmission control relay output circuit open
 
U/D Solenoid control circuit is open or shorted to ground
 
U/D Solenoid control circuit is shorted to system power
 
U/D Solenoid is damaged or has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0781

A/T Low/Reverse Pressure Switch Circuit Failure

Trouble Code Conditions: Monitored whenever engine is running. If one of the pressure switches are open or closed at the wrong time, this DTC will set.

Possible Causes:



Related DTCs present
 
Loss of Prime P0944 DTC present
 
L/R pressure switch sense circuit is open or is shorted to ground or to voltage
 
L/R pressure switch has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0833

Clutch Pedal Position Switch Circuit Malfunction

Trouble Code Conditions: Engine cranking, or vehicle speed over 25 mph at an engine speed from 1550-2880 rpm with the delta throttle over 1.1v for 4 seconds, and the PCM detected an unexpected voltage condition on the Clutch Pedal switch circuit (test must fail 5 times during one trip).

Possible Causes:



CPP switch signal circuit is open or shorted to ground
 
CPP switch power circuit is open (test the power at the PDC)
 
Clutch pedal is damaged or has failed
 
PCM has failed
 

Trouble Code: P0841

Low/Reverse Pressure Switch Sense Circuit Malfunction

Trouble Code Conditions: Switches are monitored whenever engine is running. This DTC will set if one of the pressure switches in open or closed at the wrong time in a given gear.

Possible Causes:



Related DTCs present
 
Loss of Prime P0944 DTC present
 
Transmission control relay output circuit open
 
L/R switch sense circuit is open or is shorted to ground or to voltage
 
L/R pressure switch is damaged or has failed
 
Intermittent wiring or connector problems
 
PCM has failed
 

Trouble Code: P0845

A/T 2/4 Hydraulic Pressure Test Malfunction

Trouble Code Conditions: Engine speed over 1000 rpm, then immediately after a shift event, the PCM detected a failure in one or more of the Pressure Switch circuits (i.e., it tests switches that are not operating).

Possible Causes:



2/4 pressure is incorrect, or internal transmission faults exist
 
2/4 pressure switch circuit is open, shorted to ground or power
 
2/4 pressure switch is damaged or it has failed
 
Transmission solenoids/TRS assembly is damaged or have failed
 
TCM relay power circuit to 2/4 switch is open (loss of B+)
 
Intermittent wiring or connector problems exist
 
PCM or TCM has failed
 

Trouble Code: P0846

A/T 2/4 Pressure Switch Circuit Malfunction

Trouble Code Conditions: Engine started; vehicle driven in a forward gear, and the PCM detected that the 2/4 Pressure Switch circuit indicated open or closed at the wrong time. Related relay DTCs may be present.

Possible Causes:



2/4 pressure is incorrect, or internal transmission faults exist
 
2/4 pressure switch circuit is open, shorted to ground or power
 
2/4 pressure switch is damaged or it has failed
 
TCM relay power circuit to L/R switch is open (loss of B+)
 
PCM/TCM has failed
 

Trouble Code: P0850

A/T Park/Neutral Switch Performance

Trouble Code Conditions: Engine running; gearshift selector in Park, Neutral or Drive position (not Limp-In mode). The PCM detected an invalid Park/Neutral switch state during vehicle operation.

Possible Causes:



Check for any TCM related codes stored in the TCM controller
 
PCM has failed
 

Trouble Code: P0870

A/T Hydraulic Pressure Line Malfunction

Trouble Code Conditions: Engine started; vehicle driven at over 1000 rpm, then immediately after a shift, the PCM detected a malfunction in one or more of the Pressure Switch circuits (it detected the switch did not close twice). DTC P0944 may be present.

Possible Causes:



Check for related line pressure trouble codes
 
Check for related speed ratio and pressure switch codes
 
5v supply circuit is open or is shorted to ground
 
Transmission Control Relay output circuit is open
 
OD Pressure Switch sense circuit is shorted to ground or to voltage
 
Excessive debris in the oil pan
 
Line pressure Sensor connector is loose or damaged
 
Oil pressure switch is damaged or has failed
 
Intermittent wiring or connector problems exist
 
PCM or TCM has failed
 

Trouble Code: P0871

A/T O/D Pressure Switch Circuit Malfunction

Trouble Code Conditions: Engine started; vehicle driven in a forward gear, and the PCM detected that the O/D Pressure Switch circuit indicated open or closed at the wrong time.

Possible Causes:



Related DTCs may be present
 
O/D pressure is incorrect, or internal transmission faults exist
 
O/D pressure switch circuit is open, shorted to ground or power
 
O/D pressure switch is damaged or it has failed
 
TCM relay power circuit to O/D switch is open (loss of B+)
 
Intermittent wiring or connector problems exist
 
PCM or TCM has failed
 

Trouble Code: P0884

Power-Up Automatic Transmission Speed Malfunction

Trouble Code Conditions: Engine started, TCM relay enabled; and the TCM detected a valid forward gear PNDRL signal with the Output Speed more than 800 rpm indicating a vehicle speed of over 20 mph. Note: The TCM has separate powers and grounds specifically to its portion of the PCM.

Possible Causes:



TCM power supply circuit to direct battery is open
 
TCM power supply circuit to the ignition switch is open
 
TCM power ground circuit is open or the connector is loose
 
TCM has failed
 

Trouble Code: P0888

A/T Relay Output Malfunction

Trouble Code Conditions: Engine started, TCM relay enabled and monitored continuously. This DTC sets when less than 3v are present at the relay output circuits at the TCM when the TCM is energizing the relay. Note: Due to the integration of the PCM and TCM, the transmission part of the PCM has its own specific power and ground circuits.

Possible Causes:



Fused B+ circuit is open
 
TC relay output circuit is open or is shorted to ground
 
TC relay control circuit is open or is shorted to ground
 
TC relay ground circuit is open
 
TC relay has failed
 
Intermittent wiring or connector problems exist
 
Transmission solenoid/pressure switch assembly has malfunctioned or failed
 
PCM/TCM has failed
 

Trouble Code: P0890

A/T TCM Switched Battery Circuit Malfunction

Trouble Code Conditions: Ignition switch position is changed from one position to another. TCM relay "not" energized, and the TCM detected voltage present at any of the Pressure Switch input circuits. Note: Due to the integration of the PCM and TCM, the transmission part of the PCM has its own specific power and ground circuits.

Possible Causes:



2/4 switch circuit is shorted to system power (B+)
 
L/R switch circuit is shorted to system power (B+)
 
O/D switch circuit is shorted to system power (B+)
 
TCM switched battery circuit is damaged
 
Intermittent wiring or connector problems exist
 
PCM/TCM has failed
 

Trouble Code: P0891

A/T TCM Relay Always On

Trouble Code Conditions: Key on or engine cranking; TCM relay "not" energized, and the TCM detected voltage present at the TCM output circuit during the test. Note: Due to the integration of the PCM and TCM, the transmission part of the PCM has its own specific power and ground circuits.

Possible Causes:



TCM relay output circuit is shorted to system power (B+)
 
TCM relay control circuit is shorted to system power (B+)
 
TCM relay is damaged or it has failed (it may be stuck closed)
 
Intermittent wiring or connector problems exist
 
PCM/TCM has failed
 

Trouble Code: P0897

A/T Transmission Fluid Burnt Or Worn Out

Trouble Code Conditions: Engine started; vehicle driven, and immediately after a transition from full TCC lockup to partial TCC engagement (for A/C bump prevention), the TCM detected vehicle shutter during engagement.

Possible Causes:



Automatic transmission fluid is burnt or contaminated
 
Automatic transmission fluid is worn out
 

Trouble Code: P0944

A/T Loss Of Prime Pressure

Trouble Code Conditions: Engine started; vehicle driven, and immediately after a slipping condition is detected with the pressure switches "not" indicating pressure, the PCM detected a loss of prime pressure. In effect, the TCM turns "on" available elements to detect if prime pressure exists. The DTC sets if no pressure switches respond.

Possible Causes:



A/T pressure switch connector is damaged, loose or shorted
 
Invalid PRNDL code (shift lever position error)
 
Automatic transmission fluid level is too low
 
Transmission oil filter is clogged or severely restricted
 
Transmission oil pump is damaged or weak
 
Intermittent wiring or connector problems exist
 

Trouble Code: P0952

A/T AutoStick Sensor Circuit Malfunction

Trouble Code Conditions: Engine started; vehicle driven, transmission not in AutoStick position, and the TCM that either the Upshift or Downshift switch was closed (below 0.3v), or if both the Upshift and Downshift switches are closed at the same time.

Possible Causes:



AutoStick assembly is damaged or has failed
 
Intermittent wiring or connector problems exist
 
Downshift sense or Upshift sense circuit is shorted to ground
 
PCM/TCM has failed
 

Trouble Code: P0953

A/T AutoStick Sensor Circuit High

Trouble Code Conditions: The AutoStick circuit is checked every .007 second, with the ignition on and in both AutoStick and non-AutoStick modes. If the TCM detects circuit voltage rises above 4.8v, this DTC will set.

Possible Causes:



AutoStick assembly is damaged or has failed
 
Intermittent wiring or connector problems exist
 
Downshift sense or Upshift sense circuit is shorted to ground
 
PCM/TCM has failed
 

Trouble Code: P0992

A/T 2/4 & O/D Hydraulic Pressure Test Malfunction

Trouble Code Conditions: Engine started; vehicle driven at over 1000 rpm, then immediately after a shift, the PCM detected a malfunction in one or more of the Pressure Switch circuits (it tests the switches that are not operating). If the pressure switch does not close 2 times, the DTC will set.

Possible Causes:



2/4 pressure switch circuit is open, shorted to ground or power
 
2/4 pressure switch is damaged or it has failed
 
O/D pressure switch circuit is open, shorted to ground or power
 
O/D pressure switch is damaged or it has failed
 
Internal transmission faults exist
 
TCM relay power circuit to 2/4 or O/D switch open (loss of B+)
 
PCM/TCM has failed
 

Trouble Code: P1105

Throttle Inlet Pressure Sensor Solenoid Circuit Malfunction

Trouble Code Conditions: Engine started, system voltage over 10.5v, Turbo Boost mode enabled, and the PCM detected the Actual and Intended state of the Throttle Inlet Pressure Sensor solenoid did not match.

Possible Causes:



ASD output circuit to the TIP solenoid is open
 
Throttle inlet pressure Sensor solenoid is damaged or has failed
 
TIP solenoid control circuit is open, shorted to ground or power
 
PCM has failed
 

Trouble Code: P1106

Throttle Inlet Pressure Sensor Solenoid Circuit Malfunction

Trouble Code Conditions: Engine started; battery over 10.5v; Turbo Boost mode enabled. The PCM did not detect enough difference between BARO Sensor and TIP Sensor values during boost.

Possible Causes:



Check the vacuum supply to the turbo surge solenoid unit
 
Inspect the hoses and tubing to the turbo charger assembly
 
Review results of Solenoid Tests (Test 1, 2, 3 and 4 results)
 
Turbocharger assembly is damaged or it has failed
 
Wastegate actuator has failed (due to a mechanical failure)
 

Trouble Code: P1115

General Temperature Sensor Performance

Trouble Code Conditions: Engine "off" more than 8 hours, then engine started, ambient temperature above -10ºF; and after a calibrated amount of cool-down time, the PCM compares the values from the Ambient Air Temperature (AAT), Engine Coolant Temperature (ECT) and Intake Air Temperature (IAT) Sensors. If the PCM detects that the value of any combination of these Sensors (AAT-IAT, AAT-ECT or ECT-IAT) is less than a calibrated value, it will set this trouble code.

Possible Causes:



Sensor signal circuit is open or shorted to ground
 
Sensor ground circuit is open or shorted to VREF (5v)
 
One or more of the identified Sensors is out-of-calibration
 
Ambient air temperature Sensor is damaged or it has failed
 
PCM High or Low circuit is damaged or it has failed
 

Trouble Code: P1135

O2 (B1 S1) Heater Element Resistance Out-Of-Range

Trouble Code Conditions: Monitored with engine running; O2 (B1 S1) Sensor has reached 98% of duty cycle at least once since cranking; vehicle speed is between 20-93 mph; catalyst temperature is between 1112-1706F (600-930C); battery voltage is 9-16v; and no O2 Sensor electrical DTCs are present. If the PCM determines the O2 Sensor resistance is less than 2 ohms for more than 30 seconds, this DTC will set.

Possible Causes:



O2 heater element has failed
 
O2 Sensor heater ground circuit is open
 
ASD relay output circuit is open
 
Intermittent condition
 
PCM has failed
 

Trouble Code: P1136

O2 (B1 S2) Heater Element Resistance Out-Of-Range

Trouble Code Conditions: Monitored with engine running; O2 Sensor has reached 98% of duty cycle at least once since cranking; vehicle speed is between 20-93 mph; catalyst temperature is between 1112-1706F (600-930C); battery voltage is 9-16v; and no O2 Sensor electrical DTCs are present. If the PCM determines the B1 S2 O2 Sensor resistance is less than 2 ohms for more than 30 seconds, this DTC will set.

Possible Causes:



O2 heater element has failed
 
O2 Sensor heater ground circuit is open
 
ASD relay output circuit is open
 
Intermittent condition
 
PCM has failed
 

Trouble Code: P1188

Throttle Inlet Pressure Sensor Signal Range/Performance

Trouble Code Conditions: Engine started, engine running in Turbo Boost or Non-Boost mode, and the PCM detected a significant difference between the BARO Sensor and TIP Sensor signals (i.e., the TIP Sensor cannot read the signal correctly).

Possible Causes:



ASD output circuit to the TIP solenoid is open
 
Throttle inlet pressure Sensor solenoid is damaged or has failed
 
TIP solenoid control circuit is open, shorted to ground or power
 
PCM has failed
 

Trouble Code: P1189

Throttle Inlet Pressure Sensor Circuit Low Input

Trouble Code Conditions: Engine started, TP Sensor less than 1.2v, system voltage over 10.5v, and the PCM detected the Throttle Inlet Pressure (TIP) Sensor was less than 0.0782v for a period of 1-7 seconds.

Possible Causes:



TIP Sensor VREF circuit is open
 
TIP Sensor signal circuit is open
 
TIP Sensor signal circuit is shorted to chassis or Sensor ground
 
TIP Sensor is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1190

Throttle Inlet Pressure Sensor Circuit High Input

Trouble Code Conditions: Engine started, TP Sensor less than 1.2v, system voltage over 10.5v, and the PCM detected the Throttle Inlet Pressure (TIP) Sensor was more than 4.92v for a period of 1-7 seconds.

Possible Causes:



TIP Sensor VREF circuit is open
 
TIP Sensor signal circuit is open
 
TIP Sensor signal circuit is shorted to chassis or Sensor ground
 
TIP Sensor is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1196

O2 (B2 S1) Circuit Insufficient Activity

Trouble Code Conditions: Engine started, vehicle driven with the throttle open at a speed over 18-55 mph at light engine load for over 5 minutes, ECT Sensor more than 170ºF, and the PCM detected the O2 signal switched from 0.39v to 0.60v too few times in the Oxygen Sensor Monitor test.

Possible Causes:



Base engine mechanical fault affecting more than one cylinder
 
Exhaust leak present in exhaust manifold or exhaust pipes
 
O2 element fuel contamination or has deteriorated
 
O2 signal circuit or ground circuit has high resistance
 

Trouble Code: P1281

Engine Is Cold Too Long

Trouble Code Conditions: Engine started, engine runtime more than 20 minutes, and the PCM detected the engine temperature did not exceed 176ºF in the period.

Possible Causes:



Check the operation of the thermostat (it may be stuck open)
 
ECT Sensor signal circuit has high resistance
 
ECT Sensor is damaged or it has failed
 
Inspect for low coolant level or an incorrect coolant mixture
 

Trouble Code: P1282

Fuel Pump Relay Control Circuit Malfunction

Trouble Code Conditions: Key on or engine started, system voltage over 10.5v, and the PCM detected an unexpected voltage condition on the Fuel Pump Relay control circuit during the CCM test period.

Possible Causes:



Fuel pump relay control circuit is open or shorted to ground
 
Fuel pump relay power circuit is open (test power from Ignition)
 
Fuel pump relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1294

Target Idle Speed Not Reached

Trouble Code Conditions: DTC P0106, P0107, P0108, P0121, P0122 and P0123 not set, engine started, running at idle in Drive or Neutral, and the PCM detected the Actual idle speed was more than 200 rpm over or more than 100 rpm less than the Target speed for over 14 seconds.

Possible Causes:



Engine vacuum leak in a hose, brake booster or in the engine
 
IAC motor control circuits open or grounded in the wire harness
 
Throttle body dirty or restricted (trying cleaning it and retesting)
 
Throttle linkage or throttle plate not in the correct position
 
PCM has failed
 

Trouble Code: P1296

5-Volt VREF Supply Not Present

Trouble Code Conditions: Key on, altitude indicating zero feet above seal level, then the PCM detected the MAP Sensor was near 101 kPa; or with altitude at 1200 feet above sea level, the MAP Sensor was near 88 kPa.

Possible Causes:



MAP Sensor VREF circuit open between the Sensor and PCM
 
MAP Sensor ground circuit open between the Sensor and PCM
 
MAP Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1297

No Change In MAP Signal From Start To Run Transition

Trouble Code Conditions: Engine started, and with the engine speed within 64 rpm of the Target idle speed, the PCM detected too small a difference between the BARO and MAP Sensor signals for 8.80 seconds.

Possible Causes:



Engine vacuum port to MAP Sensor clogged, dirty or restricted
 
MAP Sensor signal is skewed or the Sensor is out-of-calibration
 
MAP Sensor VREF circuit open or grounded (intermittent fault)
 
PCM has failed
 

Trouble Code: P1388

Auto Shutdown Relay Control Circuit Malfunction

Trouble Code Conditions: Key on or engine cranking; and the PCM detected an unexpected voltage condition on the ASD Relay Control circuit. The ASD Relay coil resistance is 95-105 ohms at 68ºF.

Possible Causes:



ASD relay control circuit is open between the relay and PCM
 
ASD relay control circuit is shorted to ground
 
ASD relay power circuit is open (test power from Fused B+)
 
ASD relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1389

No Auto Shutdown Relay Output Voltage To PCM

Trouble Code Conditions: Engine cranking; and the PCM did not detect any voltage on the ASD Relay Output circuit to the PCM during the CCM test.

Possible Causes:



ASD relay connector is damaged, loose or shorted
 
ASD relay output circuit is open between the relay and PCM
 
ASD relay power circuit is open (test power from Fused B+)
 
ASD relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1391

CKP Or CMP Sensor Signal Intermittent

Trouble Code Conditions: Engine started, engine running, and after every 69-degree CKP Sensor leading edge and trailing signal edge is determined, the PCM updates this data and compares it to the true CMP Sensor port level. If the PCM detects a disagreement between these two values 20 times in succession, this trouble code is set.

Possible Causes:



Camshaft Sensor is not installed properly
 
Engine valve timing is not within specifications
 
Perform a CKP and CMP Sensor relearn with the scan tool
 
Tone wheel or pulse ring is damaged
 

Trouble Code: P1398

Misfire Adaptive Numerator At Limit

Trouble Code Conditions: Engine started; ECT Sensor under 75ºF; engine runtime over 50 sec.; A/C "OFF"; vehicle speed over 36 mph in 1st gear, or over 65 mph in high gear, followed by a closed throttle decel period. This code sets if the PCM detects one of the CKP Sensor target windows varies more than 2.86% from the reference window. Background - PCM needs to learn any variation in engine machining to detect when a misfire is present. CKP Sensor has 2 40 windows that are 180 apart. The window for Cylinders 1 and 4 is the reference window. It is checked against the window for Cylinders 2 and 3. The PCM checks for any variation to make engine speed adjustments.

Possible Causes:



Base engine problem (i.e., low cylinder compression)
 
CKP Sensor crankshaft target variation too large
 
CKP Sensor improperly installed or the CKP Sensor has failed
 
CKP Sensor signal circuit open or shorted (intermittent fault)
 
Tone wheel or pulse ring is damaged
 

Trouble Code: P1486

EVAP Leak Detection Monitor Pinched Hose Detected

Trouble Code Conditions: BTS from 40-96ºF and ECT Sensor within 20ºF of the BTS signal at startup (cold engine), engine started, and after the EVAP Leak Detection test was enabled, the PCM detected the LDP switch did not reach 3 closures (i.e., a "no flow" condition was present).

Possible Causes:



EVAP vapor hose blocked between the fuel tank and the LDP (i.e., in the OLFV, rollover or vapor hose)
 
EVAP canister is clogged or full of dirt or moisture
 
EVAP ventilation solenoid is damaged or has failed
 
Purge line is loose, damaged or incorrectly routed
 
PCM has failed
 

Trouble Code: P1492

Battery Temperature Sensor Circuit High Input

Trouble Code Conditions: Key on or engine running; and the PCM detected the BTS signal indicated more than 4.90v for 3 seconds during the CCM test.

Possible Causes:



BTS signal circuit is open between the Sensor and the PCM
 
BTS ground circuit is open between the Sensor and the PCM
 
BTS (Sensor) is damaged or the PCM has failed
 

Trouble Code: P1493

Battery Temperature Sensor Circuit Low Input

Trouble Code Conditions: Key on or engine running; and the PCM detected the BTS signal indicated less than 0.30v for 3 seconds during the CCM test.

Possible Causes:



BTS circuit is shorted to ground between Sensor and the PCM
 
BTS (Sensor) is damaged or has failed
 
PCM has failed
 

Trouble Code: P1494

EVAP Leak Detection Pump Switch Or Mechanical Fault

Trouble Code Conditions: BTS from 40-96ºF and ECT Sensor within 10ºF of the BTS signal at startup (cold engine), engine started, and the PCM detected the LDP switch was not in its expected state at key "on" or engine running.

Possible Causes:



LDP switch signal circuit is open or shorted to ground
 
LDP switch power circuit is open (test power to Fused Ignition)
 
LDP vacuum hose is clogged, loose or restricted
 
LDP assembly is damaged or has failed (the switch has failed)
 

Trouble Code: P1495

Leak Detection Pump Solenoid Circuit Malfunction

Trouble Code Conditions: Engine started, ECT Sensor from 40-90ºF and within 10ºF of the Battery Temperature Sensor signal, engine running, and the PCM detected the Actual state of the Leak Detection Pump solenoid did not match the Intended state of the solenoid during the test period.

Possible Causes:



LDP power supply circuit from the ignition switch is open
 
LDP solenoid control circuit is open or shorted to ground
 
LDP assembly is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1593

Speed Control Switch Stuck Operation

Trouble Code Conditions: Ignition on. Either S/C switch is mechanically stuck in On/Off, Resume/Accel or Set position for too long.

Possible Causes:



Intermittent speed control switch 1/2 stuck DTC
 
S/C switches or Steering Column Control Module malfunctioning
 
S/C signal circuit open or shorted ground or to battery voltage
 
S/C switch signal circuit shorted to switch return circuit
 
S/C Sensor ground open
 
PCM has failed
 

Trouble Code: P1594

Charging System Voltage Too High

Trouble Code Conditions: Engine is running at more than 380 rpm. If the battery voltage is 1v greater than the desired voltage, this DTC will set.

Possible Causes:



Intermittent condition
 
Generator field driver circuit is shorted to ground
 
Generator field is damaged or has failed
 
PCM has failed
 

Trouble Code: P1598

A/C Pressure Sensor Circuit High Input

Trouble Code Conditions: Engine started, engine running, A/C Relay is "on", and the PCM detected the A/C Pressure Sensor indicated more than 4.90v.

Possible Causes:



A/C pressure Sensor circuit is open or shorted to VREF (5v)
 
A/C pressure Sensor ground circuit is open
 
A/C pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1599

A/C Pressure Sensor Circuit Low Input

Trouble Code Conditions: Engine started, engine running, A/C Relay is "on", and the PCM detected the A/C Pressure Sensor indicated less than 0.70v.

Possible Causes:



A/C pressure Sensor circuit is shorted to ground
 
A/C pressure Sensor power circuit is open
 
A/C pressure Sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1602

PCM Not Programmed

Trouble Code Conditions: Key on. The PCM detected that it had not been programmed.

Possible Causes:



Program the PCM and then retest for this same trouble code
 
PCM has failed
 

Trouble Code: P1603

Powertrain Control Module Internal Dual-Port Ram Communication

Trouble Code Conditions: Key on; and the PCM detected an error message that indicated that it had not been programmed or that it was programmed properly.

Possible Causes:



Fused ignition switch output is missing (off-start-run circuit)
 
PCM is damaged or it has an internal failure
 

Trouble Code: P1604

PCM Internal Dual-Port Ram Read/Write Integrity Failure

Trouble Code Conditions: Key on; and the PCM detected an error message that indicated it had not been programmed, or it was not programmed properly.

Possible Causes:



Fused ignition switch output is missing (off-start-run circuit)
 
PCM is damaged or it has an internal failure
 

Trouble Code: P1607

Powertrain Control Module Internal Shutdown Timer Rationality

Trouble Code Conditions: Cold engine startup, and after the PCM compared the coolant temperature to the shutdown time, it detected a rationality fault.

Possible Causes:



Fused ignition switch output is missing (off-start-run circuit)
 
PCM is damaged or it has an internal failure
 

Trouble Code: P1616

Primary 5v Sensor Reference Voltage Low

Trouble Code Conditions: Key on. If the PCM detects a voltage of less than 4.75v on the primary 5v supply circuit for at least 100ms, this DTC will set.

Possible Causes:



Intermittent condition
 
Primary 5v supply circuit shorted to ground
 
PCM has failed
 

Trouble Code: P1617

Primary 5v Sensor Reference Voltage High

Trouble Code Conditions: Key on. If the PCM detects a voltage of more than 5.25v on the primary 5v supply circuit for at least 100ms, this DTC will set.

Possible Causes:



Intermittent condition
 
Primary 5v supply circuit is open or is shorted to voltage
 
PCM has failed
 

Trouble Code: P1618

Primary 5v Sensor Reference Voltage Unstable

Trouble Code Conditions: Key on. If the PCM detects a voltage variance of more than 0.25v on the primary 5v supply circuit for more than 100ms, this DTC will set.

Possible Causes:



Primary 5v supply circuit open or shorted to ground or to battery voltage
 
5v Sensor has failed
 
PCM has failed
 

Trouble Code: P1626

Secondary 5v Sensor Reference Voltage Low

Trouble Code Conditions: Key on. If the PCM detects a voltage of less than 4.75v on the secondary 5v supply circuit for more than 100ms, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit shorted to ground
 
5v Sensor has failed
 
PCM has failed
 

Trouble Code: P1627

Secondary 5v Sensor Reference Voltage High

Trouble Code Conditions: Key on. If the PCM detects a voltage of more than 5.25v on the secondary 5v supply circuit for more than 100ms, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit is open or is shorted to voltage
 
5v Sensor has failed
 
PCM has failed
 

Trouble Code: P1628

Secondary 5v Sensor Reference Voltage Unstable

Trouble Code Conditions: Key on. If the PCM detects a voltage variance of more than 0.25v on the secondary 5v supply circuit for more than 100ms, this DTC will set.

Possible Causes:



Intermittent condition
 
ETC assembly has failed
 
5v supply circuit has high resistance
 
PCM has failed
 

Trouble Code: P1652

Serial Communication Link Malfunction

Trouble Code Conditions: Engine started; and after the TCM did not detect any signals on the Serial Communication Line for more than 20 seconds. Note: Due to the integration of the PCM and TCM, Bus communication between the modules is internal.

Possible Causes:



TCM cannot communicate with the Instrument Cluster (MIC)
 
TCM cannot communicate with the Powertrain Control Module
 
PCM/TCM is damaged or it has an internal failure
 

Trouble Code: P1653

PCI Bus Shorted To Ground

Trouble Code Conditions: Key on. If the PCM detects a short to ground on the PCI Bus for more than 5 seconds, this DTC will set.

Possible Causes:



Intermittent condition
 
Internal controller short to ground
 
PCI Bus short to ground
 

Trouble Code: P1654

PCI Bus Shorted To Voltage

Trouble Code Conditions: Key on. If the PCM detects a short to voltage on the PCI Bus for more than 5 seconds, this DTC will set.

Possible Causes:



Intermittent condition
 
Internal controller short to battery voltage
 
PCI Bus short to voltage
 

Trouble Code: P1682

Charging System Voltage Too Low

Trouble Code Conditions: Engine started; engine speed over 1152 rpm, and the PCM detected the Battery Sense circuit was 1.0v less than the Charging System circuit for 25 seconds during the CCM test (Generator Lamp is "on").

Possible Causes:



Battery positive or Fused Ignition circuit has high resistance
 
Generator drive belt out-of-adjustment or worn out
 
Generator field circuit has a high resistance condition
 
PCM has failed
 

Trouble Code: P1684

Battery Has Been Disconnected

Trouble Code Conditions: Key on, and the TCM detected that it had been disconnected from the Battery Direct (B+) circuit or its Power Ground circuit. This DTC will also set during the scan tool Quick Battery Disconnect procedure. Note: Due to the integration of the PCM and TCM, the transmission part of the PCM has its own specific power and ground circuits.

Possible Causes:



Quick Learn procedure was performed with scan tool
 
TCM battery direct (B+) circuit is open or disconnected
 
TCM power ground circuit is open
 
PCM/TCM was disconnected or it has been replaced
 

Trouble Code: P1686

No SKIM Bus Message Received

Trouble Code Conditions: Key on. If the PCM does not receive a Bus message from the SKIM when expected, this DTC will set.

Possible Causes:



Intermittent condition
 
SKIM/PCM has failed
 
Loss of SKIM communication link
 
PCI Bus circuit open from PCM to SKIM
 

Trouble Code: P1687

No Cluster Bus Messages

Trouble Code Conditions: Key on or engine running; and the PCM determined that it did not receive any Security Key Bus Messages over the Data Bus line for 20 seconds. This malfunction may be an intermittent problem.

Possible Causes:



Data Bus circuit from SKIM to PCM is damaged or it is open
 
PCM unable to communicate with the Body Control Module
 
PCM has failed, or the SKIM is damaged or has failed
 

Trouble Code: P1694

No PCM Bus Messages

Trouble Code Conditions: Ignition on or engine started; system voltage over 10.5v and the PCM determined that it did not receive any Bus messages for 10 seconds. Note: Due to the integration of the PCM and TCM, Bus communication between the modules is internal.

Possible Causes:



Data Bus circuit connector is damaged, open or it is shorted
 
Data Bus circuit to the PCM is damaged or it is open
 
PCM unable to communicate with the body control module
 
Intermittent wiring or connector problems exist
 
PCM has failed
 

Trouble Code: P1695

No BCM Bus Messages

Trouble Code Conditions: Engine started; system voltage over 10.5v and the TCM determined that it did not receive any BCM messages for 20 seconds.

Possible Causes:



Data Bus circuit from BCM to the PCM is damaged or it is open
 
BCM is damaged or has failed
 
TCM unable to communicate with the TCM
 
TCM has failed
 

Trouble Code: P1696

PCM EEPROM Write Operation Denied/Invalid

Trouble Code Conditions: Engine started or ignition on continuously. PCM detected an unsuccessful attempt to program/write to the internal EEPROM. Occurred at initialization or shutdown.

Possible Causes:



DRB or scan tool displays a "write" failure occurred
 
DRB or scan tool displays "write" refused a second time
 
DRB or scan tool displays SRI mileage invalid (compare the SRI mileage reading to the reading on the odometer)
 
PCM has failed
 

Trouble Code: P1697

PCM Failure (EMR/SRI Mileage Not Stored)

Trouble Code Conditions: Key on, and the PCM detected an unsuccessful attempt to "write" the Service Reminder Indicator (SRI) or Emission Mileage Request (EMR) mileage to an EEPROM located occurred during initialization.

Possible Causes:



Clear the trouble codes and retest for the same trouble code. If DTC P1697 resets, replace the PCM and then reprogram it.
 

Trouble Code: P1775

A/T Solenoid Switch Latched In TCC Position

Trouble Code Conditions: Engine started; vehicle driven to over 15 mph and the TCM detected the Transmission did not shift into 1st Gear (test must fail 3 times).

Possible Causes:



Related DTC P0841 may be present.
 
Intermittent wiring or connector problems
 
Extremely low battery (system) voltage
 
L/R Solenoid pressure switch circuit is open or switch has failed
 
Transmission solenoid pack is damaged or has failed
 
Transmission control relay circuit is shorted to L/R solenoid
 
Valve body engine idle too high
 
Valve body solenoid switch stuck in "lockup" position
 
PCM has failed
 

Trouble Code: P1776

A/T Solenoid Switch Latched In Low/Reverse Position

Trouble Code Conditions: Engine started; vehicle driven to over 30 mph and the TCM detected the L/R switch was closed while performing partial or full PEMCC or FEMCC.

Possible Causes:



Related DTC P0841 may be present.
 
Intermittent wiring or connector problems
 
L/R pressure switch sense circuit is open, shorted to ground or to voltage
 
Extremely low battery (system) voltage
 
Transmission pan has debris caused by valve body damage
 
Transmission internal problems, SSV sticking, or valve body damage
 
PCM has failed
 

Trouble Code: P1790

A/T Malfunction Immediately After Shift Event

Trouble Code Conditions: Engine started; vehicle driven to a speed over 10 mph in Drive, and the TCM detected a Speed Ratio error within 1.3 seconds of a shift.

Possible Causes:



Transmission internal mechanical problem
 

Trouble Code: P1793

TCM TRD Link Communication Error

Trouble Code Conditions: The TCM pulses the 12v TRD signal from the PCM to ground, during torque managed shifts, with the throttle angle above 54 degrees. The TRD system is also tested whenever the vehicle is stopped and the engine is at idle. This DTC is set when the TCM sends 2 subsequent torque reduction messages to the PCM and the TCM does not receive a confirmation from the PCM. Note: Due to the integrations of the PCM and TCM, Bus communication between the modules is internal. Related DTCs are present.

Possible Causes:



Torque Management Request (TMR) sense circuit is open or is shorted to ground or to voltage
 
PCM or TCM has failed
 
Intermittent wiring and connector problems
 

Trouble Code: P1794

A/T Speed Sensor Ground Circuit Malfunction

Trouble Code Conditions: Engine started; gear selector position indicating Neutral, and the PCM an error in the Output Speed Sensor signal during the test.

Possible Causes:



Extremely low battery (system) voltage
 
TCM "reset" function has just been performed
 

Trouble Code: P1797

A/T Manual Shift Overheat Malfunction

Trouble Code Conditions: Whenever the engine is running and the transmission is in the AutoStick mode, if the engine temperature exceeds 275F (135C), this DTC will set. Note: Aggressive driving or driving in Low for extended periods in AutoStick mode will set this DTC.

Possible Causes:



ATF fluid level too high (transmission may be overfilled)
 
Engine Cooling System or engine cooling fan malfunction
 
Excessive drive time in low gear, or aggressive drive patterns
 
Transmission oil cooler is clogged or restricted
 

Trouble Code: P1854

Throttle Inlet Pressure BARO Reading Out Of Range

Trouble Code Conditions: Engine started. The PCM detected the BARO Sensor indicated an incorrect reading. On Neon, MAP Sensor voltage is greater than 4.9v or below 2.28v (non-Turbo) or greater than 2.4v or below 1.2v (Turbo) for 400ms.

Possible Causes:



Inspect the hoses and tubing to the turbo charger assembly
 
Review results of Solenoid Tests (Test 1, 2, 3 and 4 results)
 
TIP signal circuit is open (may be an intermittent fault)
 
TIP ground circuit is open (may be an intermittent fault)
 
PCM has failed
 

Trouble Code: P2074

Manifold Pressure/Throttle Position Correlation; High Flow/Vacuum Leak

Trouble Code Conditions: Engine running in all drive modes. The relationship between the MAP Sensor and TP Sensor exceeds a predetermined value for a given engine speed. If vacuum drops below 1.5 in. Hg with engine rpm at more than 2000 rpm at closed throttle, or if an unexpectedly high intake manifold airflow exists that can lead to increased engine speed and puts the NGC (Ram) into a High Airflow Protection Limiting mode; in this case, rpm limits for when a TP Sensor and/or MAP Sensor limp-in fault is present.

Possible Causes:



Vacuum leak in hoses or component connections
 
High resistance or resistance to ground in MAP 5v supply or signal circuit
 
MAP Sensor has failed
 
High resistance in MAP ground circuit
 
TP Sensor has failed or is improperly adjusted
 
High resistance or resistance to ground in TP Sensor 5v supply or signal circuit
 
High resistance in TP Sensor ground circuit
 
PCM has failed
 

Trouble Code: P2096

Downstream Fuel System 1/2 Lean

Trouble Code Conditions: Engine running in closed loop mode. Ambient/battery temperature above 20F (-7C). Altitude below 8500 feet. Fuel level is more than 15%. If the PCM adds downstream short-term compensation to long-term adaptive, and a certain percentage is exceeded for 2 trips, a freeze frame is stored, the MIL illuminates and a DTC is set.

Possible Causes:



Exhaust leak
 
Engine mechanical problem
 
O2 Sensor has failed
 
O2 Sensor signal circuit or return circuit problem
 
Fuel contamination
 

Trouble Code: P2098

Downstream Fuel System 2/2 Lean

Trouble Code Conditions: Engine running in closed loop mode. Ambient/battery temperature above 20F (-7C). Altitude below 8500 feet. Fuel level is more than 15%. If the PCM adds downstream short-term compensation to long-term adaptive, and a certain percentage is exceeded for 2 trips, a freeze frame is stored, the MIL illuminates and a DTC is set.

Possible Causes:



Exhaust leak
 
Engine mechanical problem
 
O2 Sensor No. 2/2 has failed
 
O2 Sensor No. 2/2 signal circuit or return circuit problem
 
Fuel contamination
 

Trouble Code: P2099

Downstream Fuel System 2/2 Rich

Trouble Code Conditions: Engine running in closed loop mode. Ambient/battery temperature above 20F (-7C). Altitude below 8500 feet. Fuel level is more than 15%. If the PCM adds downstream short-term compensation to long-term adaptive, and a certain percentage is exceeded for 2 trips, a freeze frame is stored, the MIL illuminates and a DTC is set.

Possible Causes:



Exhaust leak
 
Engine mechanical problem
 
O2 Sensor No. 2/2 has failed
 
O2 Sensor No. 2/2 signal circuit or return circuit problem
 
Fuel contamination
 

Trouble Code: P2100

Electronic Throttle Control Motor Circuit Malfunction

Trouble Code Conditions: Ignition on and the ETC motor is not is Limp Home mode. When the PCM detects an internal error or a short between the ETC Motor and the ETC Motor positive circuit in the ETC Motor Driver, this DTC will set. The ETC light will be flashing.

Possible Causes:



Intermittent condition
 
Throttle plate or bore may have foreign object blockage
 
ETC positive circuit is open or is shorted to battery voltage, to ground, or to ETC negative circuit
 
ETC negative circuit is open or is shorted to battery voltage or to ground
 
Low battery voltage
 
ETC Motor or Throttle Body has failed
 
PCM has failed
 

Trouble Code: P2101

Electronic Throttle Control Motor Malfunction

Trouble Code Conditions: With vehicle running and ETC motor is not is Limp Home mode, and the TPS adaptation is complete. If the PCM recognizes the difference between the TPS set point and the TPS actual setting is 8 for more than 405ms, this DTC will set.

Possible Causes:



Intermittent condition
 
Electronic throttle control motor operation has failed
 
Throttle position is out of adjustment or has malfunctioned
 

Trouble Code: P2107

Electronic Throttle Control Module Processor Malfunction

Trouble Code Conditions: Ignition is on. This condition is caused by an internal PCM failure. The module will attempt to reset, so you will be able to hear the throttle relearning. If the condition is continuous, the vehicle may not be drivable. The ETC light will be flashing.

Possible Causes:



PCM requires reprogramming
 

Trouble Code: P2108

Electronic Throttle Control Module Processor Malfunction

Trouble Code Conditions: Ignition is on. This condition is caused by an internal PCM failure. Customer may experience an extended cranking condition, with limited driving and a rough idle. This code will set within 5 seconds. The ETC light will be flashing.

Possible Causes:



PCM requires reprogramming
 

Trouble Code: P2122

Accelerator Pedal Position Sensor No. 1 Circuit Low

Trouble Code Conditions: Ignition is on. When APP Sensor No. 1 voltage is less than 0.2444v, or the circuit is shorted to ground or open for more than 120msec, this DTC will set.

Possible Causes:



APP Sensor sweep
 
Intermittent condition
 
5v supply circuit is open or shorted to ground
 
APP Sensor No. 1 signal circuit is open, shorted to ground or to Sensor return circuit
 
APP Sensor No. 1 has failed
 
PCM 5v supply circuit problem
 
PCM has failed
 

Trouble Code: P2123

Accelerator Pedal Position Sensor No. 1 Circuit High

Trouble Code Conditions: Ignition is on. When APP Sensor No. 1 voltage is more than 4.8192v, because of a short to voltage, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit is shorted to battery voltage
 
APP Sensor No. 1 signal circuit is shorted to battery voltage or to 5v circuit
 
APP Sensor sweep
 
PCM has failed
 

Trouble Code: P2127

Accelerator Pedal Position Sensor No. 2 Circuit Low

Trouble Code Conditions: Ignition is on. When APP Sensor No. 2 voltage is less than 0.2444v, or the circuit is shorted to ground or open for more than 120msec, this DTC will set.

Possible Causes:



APP Sensor sweep
 
Intermittent condition
 
5v supply circuit is open or shorted to ground
 
APP Sensor No. 2 signal circuit is open, shorted to ground or to Sensor return circuit
 
APP Sensor No. 2 has failed
 
PCM 5v supply circuit problem
 
PCM has failed
 

Trouble Code: P2123

Accelerator Pedal Position Sensor No. 2 Circuit High

Trouble Code Conditions: Ignition is on. When APP Sensor No. 2 voltage is more than 4.8192v, because of a short to voltage, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit is shorted to battery voltage
 
APP Sensor No. 1 signal circuit is shorted to battery voltage or to 5v circuit
 
APP Sensor sweep
 
PCM has failed
 

Trouble Code: P2135

Throttle Position Sensors 1 & 2 Voltage Correlation

Trouble Code Conditions: Ignition is on. When the difference between TP Sensor No. 1 degrees and TP Sensor No. 2 degrees is more than 1.995 degrees, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit has high resistance
 
TP Sensor signal circuit has high resistance
 
Ground signal circuit shows high resistance
 
TP Sensors 1 & 2 require lab scope check
 
PCM has failed
 

Trouble Code: P2138

Accelerator Pedal Position Sensors 1 & 2 Voltage Correlation

Trouble Code Conditions: Ignition is on. DTCs P2122, 2123, 2127 and 2128 are not present. When APP Sensor No. 1 voltage is 1.7 times the APP Sensor No. 2 voltage, and this equals more than 0.2v for 120msec, this DTC will set.

Possible Causes:



Intermittent condition
 
5v supply circuit is open or is shorted to ground
 
APP Sensor signal circuit has high resistance
 
5v supply circuit has high resistance
 
Ground signal circuit shows high resistance
 
APP Sensors 1 & 2 require lab scope check
 
PCM has failed
 

Trouble Code: P2300

Ignition Coil No. 1 Secondary Circuit Low

Trouble Code Conditions: Ignition is on. If the PCM detects an open or short to ground on the Ignition Coil No. 1 control circuit for more than 15 coil change requests, it will set this DTC.

Possible Causes:



Ignition Coil No. 1 is damaged or it has failed
 
ASD relay output circuit problems
 
Ignition coil driver circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P2301

Ignition Coil No. 1 Secondary Circuit High

Trouble Code Conditions: Ignition is on. If the PCM detects a short to voltage on the Ignition Coil No. 1 control circuit for more than 15 coil change requests, it will set this DTC.

Possible Causes:



ASD relay output circuit problems
 
Ignition coil driver circuit is open
 
Ignition Coil No. 1 is damaged or it has failed
 
Ignition coil driver circuit is shorted to ASD output circuit
 
PCM has failed
 
Intermittent condition
 

Trouble Code: P2302

Ignition Coil No. 1 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 1 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Intermittent condition
 
Cylinder No. 1 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 1 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
ASD relay output circuit problems
 
PCM has failed
 

Trouble Code: P2303

Ignition Coil No. 2 Secondary Circuit Low

Trouble Code Conditions: Ignition is on. If the PCM detects an open or short to ground on the Ignition Coil No. 2 control circuit for more than 15 coil change requests, it will set this DTC.

Possible Causes:



Ignition Coil No. 2 is damaged or it has failed
 
ASD relay output circuit problems
 
Ignition coil driver circuit is shorted to ground
 
PCM has failed
 

Trouble Code: P2304

Ignition Coil No. 2 Secondary Circuit High

Trouble Code Conditions: Ignition is on. If the PCM detects a short to voltage on the Ignition Coil No. 2 control circuit for more than 15 coil change requests, it will set this DTC.

Possible Causes:



ASD relay output circuit problems
 
Ignition coil driver circuit is open
 
Ignition Coil No. 2 is damaged or it has failed
 
Ignition coil driver circuit is shorted to ASD output circuit
 
PCM has failed
 
Intermittent condition
 

Trouble Code: P2305

Ignition Coil No. 2 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 2 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Intermittent condition
 
Cylinder No. 2 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 2 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
ASD relay output circuit problems
 
PCM has failed
 

Trouble Code: P2308

Ignition Coil No. 3 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 3 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Intermittent condition
 
Cylinder No. 3 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 3 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
ASD relay output circuit problems
 
PCM has failed
 

Trouble Code: P2311

Ignition Coil No. 4 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 4 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Intermittent condition
 
Cylinder No. 4 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 4 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
ASD relay output circuit problems
 
PCM has failed
 

Trouble Code: P2314

Ignition Coil No. 5 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 5 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Intermittent condition
 
Cylinder No. 5 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 5 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
ASD relay output circuit problems
 
PCM has failed
 

Trouble Code: P2317

Ignition Coil No. 6 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 6 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Intermittent condition
 
Cylinder No. 6 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 6 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
ASD relay output circuit problems
 
PCM has failed
 

Trouble Code: P2320

Ignition Coil No. 7 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 7 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Cylinder No. 7 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 7 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P2323

Ignition Coil No. 8 Secondary Circuit Insufficient Ionization

Trouble Code Conditions: Engine started; and the PCM detected the Ignition Coil No. 8 secondary "burn time" was insufficient, or it was missing.

Possible Causes:



Cylinder No. 8 spark plug or wire is damaged or it has failed
 
Ignition Coil No. 8 is damaged or it has failed
 
Ignition coil control circuit is open or shorted to ground
 
PCM has failed
 

Trouble Code: P2503

Charging System Voltage Low

Trouble Code Conditions: Engine started; engine speed over 1157 rpm; PCM detected the Battery Sense voltage was 1v less than the Charging system voltage "goal" for 13.47 seconds during the CCM test. The PCM senses the battery voltage turns off the field driver and then senses the battery voltage again. If the voltages are the same, the DTC is set.

Possible Causes:



Battery sense circuit has a high resistance condition
 
Generator ground circuit has a high resistance condition
 
Generator field ground circuit is open
 
Generator field control circuit is open or shorted to ground
 
Generator is damaged or it has failed
 

Trouble Code: U0101

No TCM Bus Message

Trouble Code Conditions: Engine running. Battery voltage more than 10v. No Bus messages are received from the TCM for 20 seconds. 2 trips required.

Possible Causes:



PCI Bus unable to communicate with (DRBIII) scan tool
 
Fused ignition switch output incorrect (off-run-start)
 
Intermittent condition
 
PCM has failed
 

Trouble Code: U0155

No Cluster Bus Message

Trouble Code Conditions: Engine running. Battery voltage more than 10v. No Bus messages are received from the MIC (instrument cluster) for 20 seconds.

Possible Causes:



Communication link with instrument cluster has failed
 
Instrument cluster operation improper or has failed
 
PCM has failed
 

Trouble Code: U0168

No SKIM Bus Message

Trouble Code Conditions: Engine running or ignition on. Battery voltage more than 10v. No Bus or J1850 messages are received from the SKIM for 20 seconds.

Possible Causes:



Intermittent operation
 
PCI Bus circuit open or shorted from PCM to SKIM
 
Loss of communication between PCM and SKIM
 
SKIM or PCM has failed
 

 
label.common.footer.alt.autozoneLogo