ParkAvenue 1997-1999

Window Systems

Print

Power Windows



Removal & Installation
Motor & Regulator

Specific to:

Buick LeSabre 1986-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1992-1999

Oldsmobile Delta 88 1986-1988

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1987-1999

The power window actuator motor assembly removal does not involve removing the regulator or window assembly on most models. If your model requires these components to be removed, follow the procedures for Glass and Regulator replacement.

Specific to:

Buick LeSabre 1986-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1992-1999

Oldsmobile Delta 88 1986-1988

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1987-1999

  1. Remove door trim panel and water deflector.
  2.  
  3. Remove speaker assembly, as needed.
  4.  
  5. Detach the electrical connectors.
  6.  
  7. Unfasten the retaining screws or drill out the retaining rivets, as applicable.
  8.  
  9. Remove the actuator.
  10.  

To install:

  1. Install the actuator.
  2.  
  3. Make certain the teeth on the actuator align with teeth on the crossarm.
  4.  
  5. Install retaining screws.
  6.  
  7. Attach the electrical connector.
  8.  
  9. Check window for proper operation.
  10.  
  11. Install speaker assembly, water deflector and trim panel.
  12.  

Removal & Installation



Glass & Regulator
Power Windows
Conventional Design

Specific to:

Buick LeSabre 1986-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1992-1999

Oldsmobile Delta 88 1986-1988

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1987-1999

This procedure is for 1986-91 vehicles with the separate regulator design. If your vehicle has the modular design, follow those procedures regardless of year or model.

  1. Remove door trim panel and water deflector.
  2.  
  3. Remove the speaker assembly, if necessary.
  4.  
  5. Tape or block window to door frame in fully up position.
  6.  

Many of the door components are fastened with rivets in place of screws. These rivets must be drilled out for removal and should be replaced with new rivets, NOT screws. Screws may be longer than rivets and will cause interference or, on thin panels, screws will pull loose under use.

  1. Remove the regulator to door inner panel rivets using a 1 / 4 inch drill.
  2.  
  3. If equipped with power locks, remove the lock-to-actuator inner panel rivets.
  4.  
  5. Remove the lock actuator.
  6.  
  7. Remove the regulator guide and block assembly from the lower sash by positioning the window halfway down, and pushing the regulator forward. After removal, tape the glass in the fully up position again.
  8.  
  9. Detach the electrical connector, then remove the regulator through the access hole.
  10.  



Click image to see an enlarged view

Fig. Exploded view of the conventional window assembly and related components



Click image to see an enlarged view

Fig. Conventional power window assembly removal - 1989 LeSabre shown



Click image to see an enlarged view

Fig. Conventional power regulator assembly removal - 1989 LeSabre shown

To install:

  1. Install the window.
  2.  
  3. Install the guide and block assembly to the regulator.
  4.  
  5. Position the regulator to the door, attaching the wiring connector. Install the regulator to the door using new rivets.
  6.  
  7. To adjust the window, move it upward into the door header.
  8.  
  9. Grasp the window and move it rearward and upward into the seal, to assure full engagement of the window to run channel.
  10.  



Click image to see an enlarged view

Fig. Front door glass adjustment on vehicles with the conventional regulator assembly

  1. Tighten the window-to-sash nuts.
  2.  
  3. Tighten front nut channel bolts.
  4.  
  5. Cycle the window up and down to check operation.
  6.  
  7. Install the speaker, water deflector and trim panel.
  8.  

Modular Design

Specific to:

Buick LeSabre 1986-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1992-1999

Oldsmobile Delta 88 1986-1988

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1987-1999

This procedure is for the 1991 and newer modular design assembly. If your car has a separate regulator assembly, it may be removed using the conventional design system procedure, regardless of year or model.

  1. Remove door trim panel and water deflector.
  2.  
  3. Remove speaker assembly, as needed.
  4.  
  5. Tape or block window to door frame in fully up position.
  6.  

Many of the door components are fastened with rivets in place of screws. These rivets must be drilled out for removal and should be replaced with new rivets NOT screws. Screws may be longer than rivets causing interference or on thin panels screws will pull loose under use.

  1. Remove front channel assembly, remove the inner and outer belt strips.
  2.  
  3. Remove the sash nuts.
  4.  
  5. Carefully remove window through outboard side of door.
  6.  



Click image to see an enlarged view

Fig. Exploded view of the modular design door window assembly components



Click image to see an enlarged view

Fig. Modular design door window mounting



Click image to see an enlarged view

Fig. Replacing the power window actuator - 1992 Bonneville shown, other vehicles similar



Click image to see an enlarged view

Fig. Lower sash channel replacement



Click image to see an enlarged view

Fig. Replacement of the window sash slider assembly



Click image to see an enlarged view

Fig. Modular design front door glass adjustment - Bonneville shown, other models similar

To install:

  1. Install the window.
  2.  
  3. Install the inner and outer belt strips.
  4.  
  5. Install the sash nuts, but do not tighten.
  6.  
  7. Move window upward into door header.
  8.  
  9. Grasp window and move it rearward and upward into seal to assure full engagement of window to run channel.
  10.  
  11. Tighten the window to sash nuts.
  12.  
  13. Tighten the front nut channel bolts.
  14.  
  15. Cycle the window up and down to check operation.
  16.  
  17. Install the speaker, water deflector and trim panel.
  18.  

Regulator
Manual Windows
  1. Remove door trim panel and water deflector.
  2.  
  3. Remove speaker assembly, as needed.
  4.  
  5. Tape or block window to door frame in fully up position.
  6.  

Many of the door components are fastened with rivets in place of screws. These rivets must be drilled out for removal and should be replaced with new rivets NOT screws. Screws may be longer than rivets causing interference or on thin panels screws will pull loose under use.

  1. Remove the regulator-to-door inner panel rivets using a 1 / 4 in. drill.
  2.  
  3. Remove the lock-to-actuator inner panel rivets, if equipped with power locks.
  4.  
  5. Remove the lock actuator.
  6.  
  7. Remove the regulator guide and block assembly from lower sash by rotating regulator rearward 180 degrees.
  8.  
  9. Remove the regulator through the access hole.
  10.  



Click image to see an enlarged view

Fig. Removing the manual window regulator assembly



Click image to see an enlarged view

Fig. Separate the block from the guide by placing a flat-bladed tool into the slot and pushing downward



Click image to see an enlarged view

Fig. Crank the handle to wind the tape into the regulator, then attach the end of the tape to the regulator's tabs

To install:

  1. Install the window.
  2.  
  3. Install the inner and outer belt strips.
  4.  
  5. Install the sash nuts, but do not tighten.
  6.  



Click image to see an enlarged view

Fig. Installing the regulator to the door

  1. Move window upward into door header.
  2.  
  3. Grasp window and move it rearward and upward into seal to assure full engagement of window to run channel.
  4.  
  5. Tighten the window to sash nuts.
  6.  
  7. Tighten front nut channel bolts.
  8.  
  9. Cycle the window up and down to check operation.
  10.  
  11. Install the speaker, water deflector and trim panel.
  12.  

 
label.common.footer.alt.autozoneLogo