ParkAvenue 1997-1999

Removal & Installation

Print


CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

3.8L Engine



VIN 1 Engine

Specific to:

Buick LeSabre 1996-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1996-1999

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1996-1999

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the A/C compressor splash shield. The shield is retained by six 10mm bolts and four 7mm bolts.
  4.  
  5. Drain the cooling system into a suitable container.
  6.  
  7. Remove the supercharger drive belt and the accessory drive belt.
  8.  
  9. Unbolt the ignition coil pack and position it out of the way.
  10.  
  11. Unfasten 15mm bolt, then remove the supercharger belt tensioner.
  12.  
  13. Install a suitable engine support fixture. Raise the engine slightly for access to the engine mount.
  14.  
  15. Remove the five 15mm bolts, then remove the engine mount.
  16.  
  17. Unfasten the two 13mm bolts, then remove the power steering pump.
  18.  
  19. Remove the engine mount bracket by removing the two 15mm nuts and studs, and one 19mm nut and stud.
  20.  
  21. Remove the idler pulley.
  22.  



Click image to see an enlarged view

Fig. Unfasten the retaining bolts, then remove the idler pulley

  1. Unfasten the four 18mm bolts, then remove the water pump pulley.
  2.  
  3. Remove the four 3 / 8 in. bolts and four 1 / 2 in. bolts, then remove the water pump from the engine.
  4.  
  5. Remove and discard the gasket and thoroughly clean the gasket mating surfaces.
  6.  

To install:

  1. Install a new gasket, then position the water pump over the gasket. Install the retaining bolts and tighten to the specifications shown in the accompanying figure.
  2.  
  3. Install the water pump pulley and secure with the four 8mm bolts.
  4.  
  5. Install the idler pulley.
  6.  
  7. Install the engine mount bracket and secure with the two 15mm nuts and studs and one 19mm nut and stud.
  8.  
  9. Install the power steering pump and secure with the two 13mm bolts.
  10.  
  11. Install the engine mount and secure with the retaining bolts.
  12.  
  13. Use the engine fixture to move the engine into its original position, then remove the fixture.
  14.  
  15. Install the supercharger belt tensioner and secure with the one 15mm bolt.
  16.  
  17. Place the coil pack into position and secure with the retaining 15mm bolt.
  18.  
  19. Install the accessory and supercharger drive belts.
  20.  
  21. Fill the cooling system with the proper type and quantity of coolant.
  22.  
  23. Install the A/C compressor splash shield, securing it with the retaining bolts.
  24.  
  25. Connect the negative battery cable.
  26.  
  27. Start the engine and allow to reach normal operating temperatures. Check for leaks and top-off the coolant.
  28.  

Specific to:

Buick Park Avenue 1998-1999

Oldsmobile Regency 1998

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2.  
  3. Drain the cooling system.
  4.  
  5. Support the engine using an engine support fixture.
  6.  
  7. Remove or disconnect the following:

    Negative battery cable
     
    Air conditioning compressor splash shield
     
    Supercharger and accessory drive belts
     
    Coil pack, if equipped
     
    Supercharger belt tensioner
     
    Front engine mount
     
    Power steering pump
     
    Engine mount bracket
     
    Idler pulley
     
    Water pump pulley
     
    Water pump
     

  8.  

To install:

  1. Apply a thin bead of sealer around the outside edge of the water pump.
  2.  
  3. Install or connect the following:

    Water pump with a new gasket. Torque the short bolts to 11 ft. lbs. (15 Nm) and the long bolts to 22 ft. lbs. (30 Nm).
     
    Water pump pulley and torque the bolts to 115 inch lbs. (13 Nm)
     
    Engine mount bracket. Torque the nut closest to the a/c compressor to 33 ft. lbs. (45 Nm), and the others to 58 ft. lbs. (78 Nm).
     
    Idler pulley and torque the bolts to 37 ft. lbs. (50 Nm)
     
    Power steering pump and torque the bolts to 20 ft. lbs. (27 Nm)
     
    Front engine mount and torque the nuts to 58 ft. lbs. (78 Nm)
     
    Supercharger belt tensioner and torque the bolts to 37 ft. lbs. (50 Nm)
     
    Ignition coil pack assembly, if equipped and torque the nuts to 70 in. lbs. (8 Nm)
     
    Supercharger drive belt
     
    Accessory drive belt
     
    Air conditioning compressor splash shield
     
    Negative battery cable
     

  4.  
  5. Refill and bleed the cooling system.
  6.  
  7. Run the engine and check for leaks.
  8.  
  9. Recheck the coolant level when the engine has cooled.
  10.  

VIN K Engine

Specific to:

Buick LeSabre 1996-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1996-1999

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1996-1999

  1. Disconnect the negative battery cable.
  2.  
  3. Drain the cooling system into a suitable container.
  4.  
  5. Remove the accessory drive belt.
  6.  
  7. Unfasten the four 8mm water pump pulley bolts, then remove the pulley.
  8.  
  9. Remove the four 3 / 8 in. bolts and four 1 / 2 in. bolts, then remove the water pump from the engine.
  10.  
  11. Remove and discard the gasket and thoroughly clean the gasket mating surfaces.
  12.  



Click image to see an enlarged view

Fig. Exploded view of the water pump and gasket mounting

To install:

  1. Install a new gasket, then position the water pump over the gasket. Install the retaining bolts and tighten as follows:
    1. Tighten (1) bolts, shown in the accompanying figure, to 11 ft. lbs. (15 Nm).
    2.  
    3. Tighten (2) bolts, shown in the accompanying figure, to 22 ft. lbs. (30 Nm).

      Click image to see an enlarged view

      Fig. Water pump bolt identification

    4.  

  2.  
  3. Install the water pump pulley and secure with the four 8mm bolts.
  4.  
  5. Install the accessory drive belt.
  6.  
  7. Connect the negative battery cable.
  8.  
  9. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Check for leaks and top-off the coolant.
  10.  

Specific to:

Buick Park Avenue 1998-1999

Oldsmobile Regency 1998

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2.  
  3. Drain the cooling system.
  4.  
  5. Remove or disconnect the following:
    NOTE
    The long bolt can be removed by aligning the bolt head up with the hole in the frame rail.



    Negative battery cable
     
    Supercharger belt, if equipped
     
    Accessory drive belt
     
    Coolant hoses from the water pump
     
    Water pump pulley bolts
     



    Pulley
     
    Water pump bolts
     
    Water pump
     

  6.  

To install:

  1. Apply a thin bead of sealer around the outside edge of the water pump.
  2.  
  3. Install or connect the following:

    Water pump with new gasket. Torque the water pump short bolts to 11 ft. lbs. (15 Nm) and the long bolts to 22 ft. lbs. (30 Nm) plus an additional 80 degree turn.
     
    Water pump pulley. Torque the bolts to 115 inch lbs. (13 Nm).
     
    Coolant hoses to the water pump
     
    Drive belt
     
    Supercharger belt, if equipped
     

  4.  
  5. Refill and bleed the cooling system.
  6.  
  7. Run the engine and check for leaks.
  8.  
  9. Recheck the coolant level when the engine has cooled.

    Click image to see an enlarged view

    Fig. Exploded view of the water pump-3.8L (VIN K and 1) engines

  10.  

Except 1995 VIN 1 Engine



Specific to:

Buick LeSabre 1986-1999

Buick Park Avenue 1996-1999

Oldsmobile 88 1992-1999

Oldsmobile Delta 88 1986-1988

Oldsmobile LSS 1996-1999

Pontiac Bonneville 1987-1999

  1. Disconnect the negative battery cable.
  2.  
  3. Drain cooling system into a suitable container.
  4.  
  5. Remove the serpentine drive belt, as outlined in Section 1 of this manual.
  6.  

On some engines, removing the alternator provides better clearance for removing the water pump. For alternator removal and installation procedures, please refer to Section 2 of this manual.



Click image to see an enlarged view

Fig. After removing the alternator, remove the brace

  1. Unfasten the water pump pulley bolts, (long bolt removed through access hole provided in the body side rail), then remove the pulley.
  2.  



Click image to see an enlarged view

Fig. Pull the water pump pulley from the pump

  1. Disconnect the radiator and heater hoses from water pump.
  2.  



Click image to see an enlarged view

Fig. Use a screwdriver to loosen the hose clamp screws, then disconnect the hoses from the water pump

  1. For 1992-95 vehicles, remove the torque axis mount, as follows:
    1. Use a suitable engine support fixture and lifting bracket to raise the engine slightly to take the weight off of the engine mounts.
    2.  
    3. Remove the through-bolt from the torque axis (front) engine mount.
    4.  
    5. Lift the engine with the support fixture until the power steering reservoir touches the strut tower cross brace.
    6.  
    7. Loosen the bottom two bolts on the torque axis (front) engine mount.
    8.  
    9. Remove the A/C line clip and top two bolts on the torque axis engine mount, then remove the mount.
    10.  
    11. Remove the 2 bolts and nut attaching the engine torque axis mount bracket assembly to the front of the engine.
    12.  

  2.  

On some engines, when you remove the 13mm bolts, coolant will flow from the bolt holes, so make sure to position a drain pan under the pump before unfastening the bolts.

  1. Remove the water pump attaching bolts, then remove the water pump from the vehicle. Remove and discard the gasket. Thoroughly clean the gasket mating surfaces.
  2.  



Click image to see an enlarged view

Fig. Unfasten the water pump mounting bolts (see arrows for locations of top bolts) ...



Click image to see an enlarged view

Fig. ... then remove the water pump from the engine



Click image to see an enlarged view

Fig. Use a gasket scraper to carefully clean the water pump's mating surface



Click image to see an enlarged view

Fig. You can also use Scotchbrite® or equivalent non-abrasive scouring pad to clean the water pump gasket mating surface



Click image to see an enlarged view

Fig. When using a scraper to clean the gasket mating surfaces, be careful not to gouge the engine and cause leaks



Click image to see an enlarged view

Fig. Exploded view of the water pump mounting - 1994 vehicle shown, others similar

To install:

  1. Apply a suitable sealant to the bolt threads.
  2.  



Click image to see an enlarged view

Fig. Coat the bolt threads with a suitable sealing compound

  1. Position a new gasket, then install the water pump to the engine and tighten the retaining bolts, as follows:
  2.  



Click image to see an enlarged view

Fig. Place a new gasket on the water pump mounting surface

    1. For 1987-94 vehicles, tighten the long bolts to 29 ft. lbs. (17 Nm) and the short bolts to 97 inch lbs. (11 Nm).
    2.  
    3. For 1995 vehicles, tighten the water pump-to-block bolts to 22 ft. lbs. (30 Nm) and the water pump-to-front cover bolts to 11 ft. lbs. (15 Nm), plus an additional 80° rotation.
    4.  


  1. For 1992-95 vehicles, install the torque axis mount, as follows:
    1. Attach the torque axis engine mount bracket assembly to the front of the engine using the 2 bolts and nut.

      Click image to see an enlarged view

      Fig. Install the torque axis engine mount bracket and secure with the 2 bolts and nut

    2.  
    3. Replace the 2 upper bolts previously removed from the torque axis engine mount, and attach the mount and plastic clip for the A/C lines.
    4.  
    5. Tighten the 2 lower bolts that were previously loosened on the torque axis engine mount.

      Click image to see an enlarged view

      Fig. Exploded view of the torque axis engine mount and tightening specifications

    6.  
    7. Adjust the engine height to align the torque mount with the torque axis mount bracket.
    8.  
    9. Insert the through-bolt, attach the retaining nut and tighten to the specifications shown in the accompanying figure. Remove the engine support and lifting fixture.

      Click image to see an enlarged view

      Fig. Insert the torque axis mount bracket through-bolt

    10.  

  2.  
  3. Install the water pump pulley and secure with the retaining bolts.
  4.  
  5. Connect the radiator and heater hoses to the water pump.
  6.  
  7. Install the serpentine drive belt.
  8.  
  9. Connect the negative battery cable.
  10.  
  11. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Check for leaks and top-off the coolant.
  12.  

VIN 1 Engine



Specific to:

Buick LeSabre 1995

Buick Park Avenue 1996-1999

Oldsmobile 88 1995

Pontiac Bonneville 1995

  1. Disconnect the negative battery cable.
  2.  
  3. Drain the cooling system into a suitable container.
  4.  
  5. Remove the outer and inner drive belts, as outlined in Section 1 of this manual.
  6.  
  7. Remove the alternator and brace.
  8.  
  9. Disconnect the heater hoses and pipes from the water pump.
  10.  
  11. Remove the pulley bracket assembly.
  12.  
  13. Raise and safely support the vehicle.
  14.  
  15. Remove the power steering pump and lines.
  16.  
  17. Carefully lower the vehicle.
  18.  
  19. Remove the torque engine mount, as follows:
    1. Remove the vacuum reservoir.
    2.  
    3. Using engine support fixture J 28467-A, lifting bracket J 16854, core support wedges J 28467-130 and engine core support arm J 28467-330, raise the engine slightly to take the weight off the engine mounts.
    4.  
    5. Remove the 2 bottom bolts on the torque axis engine mount.
    6.  
    7. Remove the 2 through-bolts from the torque axis engine mount, then remove the mount.
    8.  
    9. Raise the engine to gain clearance, then remove the engine mount bracket.
    10.  

  20.  
  21. Unfasten the retainers and remove the water pump pulley.
  22.  
  23. Remove the retaining bolts, then remove the water pump from the engine.
  24.  
  25. Remove and discard the gasket and thoroughly clean the gasket mating surfaces.
  26.  

To install:

  1. Install a new gasket, then position the water pump over the gasket. Install the retaining bolts and tighten as follows:
    1. Water pump-to-block bolts: 22 ft. lbs. (30 Nm).
    2.  
    3. Water pump-to-front cover bolts: 11 ft. lbs. (15 Nm), plus an additional 80° rotation.
    4.  

  2.  
  3. Install the water pump pulley and secure with the retaining bolts.
  4.  
  5. Install the torque axis engine mount bracket, as follows:
    1. Install the engine mount bracket to the front of the engine.
    2.  
    3. Position the torque axis engine mount to the rail.
    4.  
    5. Lower the engine support fixture to align the engine mount bracket with the torque axis engine mount.
    6.  
    7. Install the 2 through-bolts, attach the retaining nuts, then tighten to the specification shown in the accompanying figures. Remove the engine support fixture, lifting bracket and core support wedges and arm.
    8.  

  6.  
  7. Raise and safely support the vehicle.
  8.  
  9. Install the power steering pump and connect the fluid lines.
  10.  
  11. Carefully lower the vehicle.
  12.  
  13. Install the pulley bracket assembly.
  14.  
  15. Connect the heater hoses and pipes.
  16.  
  17. Install the alternator and brace.
  18.  
  19. Install the inner and outer drive belts.
  20.  
  21. Connect the negative battery cable.
  22.  
  23. Bleed the power steering system. For details, please refer to Section 8 of this manual.
  24.  
  25. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Check for leaks and top-off the coolant.
  26.  

 
label.common.footer.alt.autozoneLogo