Protege 1999-2000

Sunroof

Print

Power Sunroof



Diagnosis & Testing
Limit Switch

Specific to:

Mazda Protege 1998-2003

  1. Remove the headliner. See -Headliner- in -INTERIOR- section.
  2.  
  3. Verify the glass panel position.
  4.  
  5. Disconnect the connector.
  6.  
  7. Inspect for continuity between the sunroof motor terminals using an ohmmeter.
    1. If not as specified, replace the sunroof motor.

      Click image to see an enlarged view

      Fig. Inspect for continuity between the sunroof motor terminals using an ohmmeter-Protégé (4SD)



      Click image to see an enlarged view

      Fig. Limit switch/sunroof operation test table-Protégé (4SD)

    2.  

  8.  

Motor

Specific to:

Mazda Protege 1998-2003

  1. Remove the sunroof motor.
  2.  
  3. Apply battery positive voltage to the sunroof motor terminals and inspect the operation of the sunroof motor.
    1. If not as specified, replace the sunroof motor.

      Click image to see an enlarged view

      Fig. Apply battery positive voltage to the sunroof motor terminals and inspect the operation of the sunroof motor-Protégé (4SD)

    2.  
    3. Motor should operate as follows, based on the appropriate test connection:

      B+ at terminal 2A and GND at terminal 2B: motor should turn left-slide close/tilt up
       
      GND at terminal 2A and B+ at terminal 2B: motor should turn right-slide open/tilt down
       

    4.  

  4.  

Switch

Specific to:

Mazda Protege 1999-2003

Mazda Protege5 2002-2003

  1. Check the sunroof fuses.
  2.  
  3. Apply battery voltage to terminal 2A and ground to terminal 2B, the sunroof should close/tilt up. If not check the sunroof switch.
  4.  
  5. Apply battery voltage to terminal F and ground to terminal E, the sunroof should open/tilt down. If not check the sunroof switch.
  6.  
  7. Check the sunroof switch for continuity between terminals as shown in the illustration. If the any of the tests fail, replace the switch.

    Click image to see an enlarged view

    Fig. Sunroof motor terminals-Protégé



    Click image to see an enlarged view

    Fig. Sunroof switch terminals-protégé



    Click image to see an enlarged view

    Fig. Sunroof switch continuity check-Protégé

  8.  

Removal & Installation
Motor

Specific to:

Mazda Protege 1999-2003

Mazda Protege5 2002-2003

Refer to the illustrations for component locations.

  1. Disconnect the negative battery cable.
  2.  
  3. Turn the seaming welt and weatherstrip over.
  4.  
  5. Remove the A-pillar trims.
  6.  
  7. Remove the B-pillar upper trims.
  8.  
  9. Remove the C-pillar trims.
  10.  
  11. Remove the interior and map light if not equipped with a sliding sunroof.
  12.  
  13. Remove the map light and interior light if equipped with a sliding sunroof..
  14.  
  15. Remove the screws then remove the sun visor and assist handle.
  16.  
  17. Fold tabs A up if equipped with a sliding sunroof.
  18.  
  19. Remove the fasteners.
  20.  
  21. Remove the headliner diagonally from the passenger-side front door frame.
  22.  
  23. Disconnect the sunroof motor connector.
  24.  
  25. Remove the screws, then remove the sunroof motor.
  26.  

To install:

  1. Installation is the reverse of removal.

    Click image to see an enlarged view

    Fig. Headliner assembly mounting-Protégé

  2.  

Switch

Specific to:

Mazda Protege 1999-2003

Mazda Protege5 2002-2003

The sunroof switch and the map light are a single unit.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the screws and the map light from the headliner. Unplug the connector and remove the assembly.
  4.  

To install:

  1. Installation is the reverse of removal.
  2.  

 
label.common.footer.alt.autozoneLogo