Ram 1500, 2500, 3500, 2WD & 4WD, 2001 - 2005

Wheel Hub & Bearings

Print

Adjustment



2001-02 Vehicles
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Tighten the wheel bearing nut to 30-40 ft. lbs. (41-54 Nm) while turning the rotor.
  4.  
  5. Loosen the wheel bearing adjusting nut completely.
  6.  
  7. Tighten the nut finger-tight.
  8.  
  9. Check the wheel bearing end-play. The specification is 0.001-0.003 inch (0.025-0.076mm).
  10.  
  11. Install the nut lock and cotter pin.
  12.  

2003-05 Models

These are unitized hub/bearing assemblies. No adjustment is possible.

Removal & Installation



2001-02 Vehicles
2wd Models
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Front wheel
     
    Brake caliper
     
    Grease cap
     
    Cotter pin
     
    Adjusting nut
     
    Washer
     
    Outer bearing
     
    Brake rotor and hub assembly
     
    Grease seal
     
    Inner bearing
     

  4.  

To install:

  1. Install or connect the following:

    Inner bearing
     
    Grease seal
     
    Brake rotor and hub assembly
     
    Outer bearing
     
    Washer
     
    Adjusting nut. Adjust the bearings.
     
    Cotter pin
     
    Grease cap
     
    Brake caliper
     
    Front wheel
     

  2.  

4wd Models
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Front wheel
     
    Brake caliper and rotor
     
    Hub retainer nut
     
    Hub and bearing assembly
     

  4.  

To install:

  1. Install or connect the following:

    Hub and bearing assembly. Tighten the bolts to 125 ft. lbs. (170 Nm).
     
    Hub retainer nut. Tighten the nut to 175 ft. lbs. (237 Nm).
     
    Brake caliper and rotor
     
    Front wheel
     

  2.  

2003-05 Models
Coil Spring Suspension-2wd
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Front wheel
     
    Brake caliper and rotor
     
    Wheel speed sensor
     
    Hub/bearing mounting bolts
     
    Hub/bearing assembly
     

  4.  

To install:

  1. Install or connect the following:

    Hub and bearing assembly. Tighten the bolts to 120 ft. lbs. (163 Nm).
     
    Wheel speed sensor
     
    Brake caliper and rotor
     
    Front wheel
     

  2.  

Coil Spring Suspension-4wd
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Front wheel
     
    Brake caliper and rotor
     
    Wheel speed sensor
     
    Halfshaft nut
     
    Tie rod end from the knuckle
     
    Upper ball joint from the knuckle
     
    Knuckle from the halfshaft
     
    Hub/bearing mounting bolts
     
    Hub/bearing assembly
     

  4.  

To install:

  1. Install or connect the following:

    Hub and bearing assembly. Tighten the bolts to 120 ft. lbs. (163 Nm).
     
    Knuckle onto the halfshaft
     
    Upper ball joint on the knuckle. Torque the nut to 40 ft. lbs. (54 Nm) (on 1500 series, plus 90 degrees).
     
    Tie rod end to the knuckle. Tighten the nut to 45 ft. lbs. (61 Nm) plus 90 degrees.
     
    Halfshaft nut. Torque to 185 ft. lbs. (251 Nm).
     
    Wheel speed sensor
     
    Brake caliper and rotor
     
    Front wheel
     

  2.  

Coil/Link Suspension
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Front wheel
     
    Hub extension from the rotor, if equipped
     
    Brake caliper and rotor
     
    Hub nut
     
    Wheel speed sensor wiring
     
    Hub/bearing mounting bolts 1 / 4 each. Then, tap the bolts with a mallet to loosen the hub/bearing assembly.
     
    Hub/bearing assembly, wheel studs/extension studs, rotor, shield and spacer
     
    Wheel speed sensor
     

  4.  

To install:

  1. Install or connect the following:

    Wheel speed sensor
     
    Rotor on the hub/bearing
     
    Studs
     

  2.  
  3. Apply a liberal amount of anti-seize compound on the splines of the front shaft.
  4.  
  5. Insert the 2 rearmost, top and bottom rotor hub bolts in the knuckle, so they extend from the front face as shown.

    Click image to see an enlarged view

    Fig. Hub bolt positioning

  6.  
  7. Install or connect the following:

    Spacer and shield
     
    Hub assembly onto the shaft
     

  8.  
  9. Align the bolt holes in the flange with the installed bolts. Thread the bolts onto the flange far enough to hold the unit in place.
  10.  
  11. Install the remaining bolts. Tighten all hub/bearing bolts to 149 ft. lbs. (202 Nm).
  12.  
  13. Install the washer and shaft nut. Tighten the nut to 132 ft. lbs. (179 Nm). Rotate the axle 5 to 10 times to seat the bearings. Tighten the nut to 263 ft. lbs. (356 Nm). Install a new cotter pin, advancing the nut for alignment.
  14.  
  15. The remainder of installation is the reverse of removal.
  16.  

 
label.common.footer.alt.autozoneLogo