Rendezvous 2006-2007

Removal & Installation

Print

3.4L & 3.5L Engines



  1. Drain the cooling system.
  2.  
  3. Remove the drive belt guard.
  4.  
  5. Loosen the water pump pulley bolts.
  6.  
  7. Remove the drive belt.
  8.  
  9. Remove the water pump pulley bolts.
  10.  
  11. Remove the water pump pulley.
  12.  
  13. Remove the water pump bolts.
  14.  
  15. Remove the water pump.
  16.  
  17. Remove and discard the water pump gasket.
  18.  
  19. Clean the water pump mating surfaces.

    Click image to see an enlarged view

    Fig. Exploded view of the water pump-3.4L and 3.5L Engines

  20.  

To install:

  1. Install a NEW water pump gasket onto the water pump.
  2.  
  3. Install the water pump.
    NOTE
    Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4.  
  5. Install the water pump bolts and tighten the bolts to 89 inch lbs. (10 Nm).
  6.  
  7. Install the water pump pulley.
  8.  
  9. Install the water pump pulley bolts until snug.
  10.  
  11. Install the drive belt.
  12.  
  13. Tighten the water pump pulley bolts to 18 lb ft. (25 Nm).
  14.  
  15. Install the drive belt guard.
  16.  
  17. Fill the cooling system.
  18.  

3.6L Engine



  1. Drain the cooling system until the coolant is below the water pump.
  2.  
  3. Remove the accessory drive belt from the water pump.
  4.  
  5. Use the EN 46104 tool in order to retain the water pump pulley.

    Click image to see an enlarged view

    Fig. EN 46104 installed-3.6L engine

  6.  
  7. Remove the water pump pulley bolts and the water pump pulley.
  8.  
  9. Remove the water pump bolts.
  10.  
  11. Remove the water pump.
  12.  
  13. Remove and discard the water pump gasket.
  14.  
  15. Clean the water pump sealing surfaces.
  16.  

To install:

  1. Install the NEW water pump gasket.
  2.  
  3. Install the water pump.
    NOTE
    Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4.  
  5. Install and tighten the water pump bolts to 89 inch lbs. (10 Nm).
  6.  
  7. Install the water pump pulley.
  8.  
  9. Use the EN 46104 tool in order to retain the water pump pulley.
  10.  
  11. Install and tighten the water pump pulley bolts to 106 inch lbs. (12 Nm).
  12.  
  13. Install the accessory drive belt.
  14.  
  15. Fill the cooling system.
  16.  

 
label.common.footer.alt.autozoneLogo