S10 Pickup, Sonoma 2000-2004

2.2L L4 VIN 4 Std 2

Print

Trouble Code: P0452



Fuel Tank Pressure Sensor Circuit Low Input

Possible Causes:



FTP sensor signal circuit is open or shorted to ground
 
FTP sensor VREF circuit is open or shorted to ground
 
FTP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0453



Fuel Tank Pressure Sensor Circuit High Input

Possible Causes:



FTP sensor signal circuit is shorted to VREF or system power
 
FTP sensor ground circuit is open between sensor and PCM
 
FTP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0461



Fuel Level Sensor Range/Performance

Possible Causes:



If DTC U1016 sets along with this trouble code, diagnose the cause of this code (a serial data fault) prior to testing for P0460.
 
Fuel level sensor is damaged, out-of-range or "skewed"
 
Instrument cluster or the PCM has failed
 
TSB 01-06-04-026 contains a repair procedure for this code
 

Trouble Code: P0462



Fuel Level Sensor Low Input

Possible Causes:



Fuel level sensor signal circuit is shorted to ground between the fuel level sensor and the PCM connector
 
Fuel level sender is damaged, binding or not aligned properly
 
PCM has failed
 

Trouble Code: P0463



Fuel Level Sensor High Input

Possible Causes:



Fuel level sensor signal circuit is shorted to system power
 
Fuel level sensor ground circuit is open
 
Fuel level sender is damaged, binding or not aligned properly
 
PCM has failed
 

Trouble Code: P0502



Vehicle Speed Sensor Low Input (M5/MJ1)

Possible Causes:



Transmission shaft rotor is chipped or damaged
 
VSS tip contains debris or metal shavings (an intermittent fault)
 
VSS positive (+) signal circuit is open or shorted to ground
 
VSS negative (-) signal circuit is open or shorted to ground
 
VSS is damaged or has failed
 

Trouble Code: P0503



Vehicle Speed Sensor Signal Intermittent (4T40, 4T45-E)

Possible Causes:



Transmission shaft rotor is chipped or damaged
 
OSS tip contains debris or metal shavings (an intermittent fault)
 
OSS positive (+) or (-) signal circuit open or shorted to ground
 
OSS is damaged or has failed
 

Trouble Code: P0506



Idle Speed Too Low

Possible Causes:



Air inlet duct is collapsed, loose or air filter element is clogged
 
Base engine problem (i.e., compression or misfire condition)
 
Idle air inlet passage or throttle bore is dirty or full of deposits
 
IAC solenoid control circuit has a high resistance condition
 
IAC valve is damaged or has failed
 
MAF sensor is dirty, out-of-calibration or it is "skewed"
 
Throttle plate, throttle shaft or linkage is damaged or sticking
 
PCM has failed
 

Trouble Code: P0507



Idle Speed Too High

Possible Causes:



Engine vacuum leaks, PCM valve is leaking or the wrong valve
 
Idle air inlet passage or throttle bore is dirty or full of deposits
 
IAC valve is damaged or has failed
 
MAF sensor is dirty, "skewed" or installed improperly
 
Throttle plate, throttle shaft or linkage is damaged or sticking
 
TP sensor is out-of-range or "skewed" high
 
PCM has failed
 

Trouble Code: P0530



A/C Refrigerant Pressure Sensor Circuit Malfunction

Possible Causes:



ACP sensor signal circuit is open or shorted to ground
 
ACP sensor signal circuit is shorted to VREF or system power
 
ACP sensor ground circuit is open
 
ACP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0560



System Voltage Malfunction

Possible Causes:



Check for high resistance at battery connections or at the U/H Fuse Block power circuit
 
Check the drive belt for excessive wear and the proper tension
 
Check the condition of the battery and the Generator output
 
Vehicle may have been used to jump-start another vehicle
 

Trouble Code: P0562



System Voltage Too Low

Possible Causes:



Check for high resistance at the battery connections or at the PCM IGN or PCM BAT fuse circuit connection to the PCM
 
Check the drive belt for excessive wear and the proper tension
 
Check the condition of the battery and the Generator output
 
Vehicle may have been used to jump-start another vehicle
 

Trouble Code: P0563



System Voltage Too High

Possible Causes:



Check the condition of the battery (it may be worn out)
 
Test the operation of the Generator (it may be overcharging)
 
Vehicle may have been used to jump-start another vehicle
 

Trouble Code: P0601



Control Module ROM Malfunction

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 
TSB 67-65-23 contains a repair procedure for this code
 

Trouble Code: P0602



Control Module Not Programmed

Possible Causes:



Reprogram the PCM with the correct software and calibration. If this step does not correct the problem, the PCM must be replaced and programmed with the correct software/calibration.
 

Trouble Code: P0603



Control Module Long Term Memory Reset

Possible Causes:



An interruption to the PCM main power and/or ground circuits
 
Check the PCM power and ground circuits and make repairs as necessary. Clear the codes and recheck. If it resets, the PCM must be replaced and programmed with the correct software.
 

Trouble Code: P0604



Control Module Random Access Memory Failure

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0606



Control Module Internal Performance

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0621



Generator 'L' Terminal Circuit Malfunction

Possible Causes:



Generator 'L' terminal circuit is open or shorted to power (B+)
 
Generator 'F' terminal circuit is shorted to ground
 
Generator is damaged or has failed (no output)
 
PCM has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1137



HO2S-12 Low Voltage During Power Enrichment

Possible Causes:



Air leaks present in exhaust manifold, exhaust pipes, or in the HO2S mounting location
 
HO2S may be contaminated (due to improper fuel or silicone)
 
PCM has failed
 

Trouble Code: P1171



Fuel System Lean During Acceleration

Possible Causes:



Fuel filter clogged or restricted
 
Fuel injectors dirty or restricted
 
Fuel level too low during heavy acceleration events
 
Fuel pressure regulator has failed (not supplying enough fuel)
 
Water or alcohol in fuel (low HO2S signal during acceleration)
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158ºF (70ºC). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test rpm (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (rpm) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

Trouble Code: P1380



EBTCM DTC Detected, Rough Road Data Unusable

Possible Causes:



Service the ABS before diagnosing a misfire because an actual engine misfire may or may not exist. Also, an actual engine misfire may have occurred during an ABS fault.
 
Determine if the vehicle was driven on a rough road, and the ABS could not detect this due to a malfunction. The PCM may interpret variations in crankshaft speed caused by the rough road as a misfire without an actual engine misfire present.
 
If U1016 is set, check for a fault in the IPC serial data line, its connections or in the IPC assembly or controller.
 

Trouble Code: P1381



Misfire Detected - No Communication With The EBCM

Possible Causes:



When this code is set, this indicates that a misfire was detected and that the PCM could not determine if the detected misfire was true or due to operating the vehicle on a rough surface. A misfire can be a true misfire with or without setting this code.
 
Check the IPC and EBCM for poor electrical connections at the UART serial data terminals. Verify that no true misfire exists after repairing the cause of this trouble code. If DTC U1016 is also set, this indicates that the malfunction may lie within the IPC serial data line, its electrical connections, or within the IPC.
 

Trouble Code: P1441



EVAP System Flow During Non-Purge

Possible Causes:



An improperly installed or damaged EVAP canister purge valve
 
A temporary blockage in the EVAP canister purge valve, purge pipe, or EVAP canister could cause an intermittent condition
 
FTP sensor is out-of-calibration, damaged or "skewed"
 
Purge solenoid valve is damaged or has failed
 
PCM has failed
 
TSB 02-06-04-046 contains a repair procedure for this code
 

Trouble Code: P1621



Control Module Long Term Memory Performance

Possible Causes:



Perform the OBD System Check for Engine Controls
 
The PCM needs to be replaced
 

Trouble Code: P1626



Theft Deterrent Fuel Enable Signal Lost

Possible Causes:



The most likely cause of this code is lost communications
 
If the engine starts and stalls, refer to VTD system diagnosis
 
Perform the Powertrain Onboard Diagnostic System Check
 

Trouble Code: P1630



Theft Deterrent Learn Mode Active

Possible Causes:



Refer to Programming the Theft Deterrent System
 
Perform the Powertrain Onboard Diagnostic System Check
 

Trouble Code: P1631



Theft Deterrent Fuel Enable Signal Not Correct

Possible Causes:



Refer to Diagnostic System Check for Body Control Systems
 
Perform the Powertrain Onboard Diagnostic System Check
 

Trouble Code: P1632



Theft Deterrent Fuel Disable Signal Received

Possible Causes:



Perform the Powertrain Onboard Diagnostic System Check
 
Password Learn Procedure - Attempt to start the vehicle (leave the ignition "on"). The Theft System telltale will flash for 4 seconds and then remain "on" for 10 minutes. Theft System Learn Mode will display Disabled on the Scan Tool
 
Turn the ignition "off" after the Theft System telltale goes "out".
 
Repeat steps 1 and 2 two more times. After the Theft System telltale turns "off" on the 3rd key cycle, and Theft System Learn Mode will display Enabled on the Scan Tool, attempt to start the engine. Once the engine starts the password is learned.
 

Trouble Code: P1635



5-Volt Reference 1 Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to sensor ground or chassis ground
 
5v VREF circuit, MAP or EOP sensor circuit is shorted to (B+)
 
5v VREF circuit shorted to EGR sensor High signal circuit
 
EGR solenoid valve (and sensor) is damaged or has failed
 
PCM has failed
 

Trouble Code: U1000



Class 2 Communication Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
SDM (module) could be shorted pulling the voltage low
 

Trouble Code: U1016



No Communication With Powertrain Control Module

Possible Causes:



PCM Class 2 circuit is open, shorted to ground or to B+
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
PCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1048



No Communication With Rear Wheel Steering Control Module

Possible Causes:



RWSCM Class 2 circuit is open, shorted to ground or to B+
 
RWSCM ignition power circuit has a high resistance condition
 
RESCM main ground circuit(s) has a high resistance condition
 
RESCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1064



No Communication With Body Control Module

Possible Causes:



BCM Class 2 circuit is open, shorted to ground or to B+
 
BCM ignition power circuit has a high resistance condition
 
BCM main ground circuit(s) has a high resistance condition
 
BCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1088



No Communication With SDM (Restraint Module)

Possible Causes:



SDM Class 2 circuit is open, shorted to ground or to B+
 
SDM ignition power circuit has a high resistance condition
 
SDM main ground circuit(s) has a high resistance condition
 
SDM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1096



No Communication With Instrument Panel Cluster

Possible Causes:



IPC Class 2 circuit is open, shorted to ground or to B+
 
IPC ignition power circuit has a high resistance condition
 
IPC main ground circuit(s) has a high resistance condition
 
IPC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1097



No Communication With Driver Information Center

Possible Causes:



DIC Class 2 circuit is open, shorted to ground or to B+
 
DIC ignition power circuit has a high resistance condition
 
DIC main ground circuit(s) has a high resistance condition
 
DIC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1151



No Communication With Vehicle Interface Unit

Possible Causes:



VIU Class 2 circuit is open, shorted to ground or to B+
 
VIU ignition power circuit has a high resistance condition
 
VIU main ground circuit(s) has a high resistance condition
 
VIU (module) may have failed and is pulling the circuit low
 

 
label.common.footer.alt.autozoneLogo