S10 Pickup, Sonoma 2000-2004

2.2L L4 VIN H Auto 1

Print

2.2L L4 VIN H Auto

Trouble Code: P0105



MAP Sensor Signal Range/Performance

Possible Causes:



MAP sensor signal or ground circuit has high resistance
 
MAP sensor is contaminated (moisture or icing problems)
 
MAP sensor is damaged, sticking or has failed
 

Trouble Code: P0107



MAP Sensor Circuit Low Input

Possible Causes:



MAP sensor signal circuit shorted to sensor or chassis ground
 
MAP sensor power circuit open between the sensor and PCM
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0112



IAT Sensor Circuit Low Input

Possible Causes:



IAT sensor signal circuit is shorted to sensor or chassis ground
 
IAT sensor is damaged or has failed (it may be shorted)
 
PCM has failed
 

Trouble Code: P0113



IAT Sensor Circuit High Input

Possible Causes:



IAT sensor signal circuit is open between the sensor and PCM
 
IAT sensor signal circuit is shorted to VREF or system power
 
IAT sensor is damaged or has failed (it may be open)
 
PCM has failed
 
TSB 02-06-03-005 contains a repair procedure for this code
 

Trouble Code: P0117



ECT Sensor Circuit Low Input

Possible Causes:



ECT sensor connector is damaged or shorted
 
ECT sensor signal circuit shorted to chassis or sensor ground
 
ECT sensor is damaged or has failed (it may be shorted)
 
PCM has failed
 

Trouble Code: P0118



ECT Sensor Circuit High Input

Possible Causes:



ECT sensor signal circuit is open between the sensor and PCM
 
ECT sensor signal circuit is shorted to VREF or system power
 
ECT sensor is damaged or has failed (it may be open)
 
PCM has failed
 

Trouble Code: P0122



TP Sensor Circuit Low Input

Possible Causes:



TP sensor signal circuit is shorted to sensor ground
 
TP sensor signal circuit is open (except 1996-1998 models)
 
TP sensor VREF circuit is open between sensor and PCM
 
TP sensor is damaged or it failed (it may be shorted)
 
PCM is damaged or has failed
 

Trouble Code: P0123



TP Sensor Circuit High Input

Possible Causes:



TP sensor signal circuit is shorted to VREF or system power
 
TP sensor ground circuit is open between the sensor and PCM
 
TP sensor is damaged or it failed (it may be open)
 
PCM is damaged or has failed
 

Trouble Code: P0125



ECT Excessive Time To Enter Closed Loop

Possible Causes:



Check the operation of the thermostat (it may be stuck open)
 
Coolant level is too low, or the coolant mixture is incorrect
 
ECT sensor signal circuit has a high resistance condition
 
ECT sensor is damaged or it has failed
 

Trouble Code: P0128



ECT Sensor Below Thermostat Regulating Temperature

Possible Causes:



Check the operation of the thermostat (it may be stuck open)
 
Coolant level is too low, or the coolant mixture is incorrect
 
ECT sensor signal circuit has a high resistance condition
 
ECT sensor is damaged or it has failed
 

Trouble Code: P0130



HO2S-11 (Bank 1 Sensor 1) Circuit Closed Loop Performance

Possible Causes:



Air leaks in the exhaust system, intake manifold, vacuum lines
 
EVAP Purge system malfunction or charcoal canister problems
 
HO2S signal circuit is open between the sensor and the PCM
 
HO2S signal circuit is shorted to sensor or chassis ground
 
HO2S is damaged, contaminated or air reference hole clogged
 
PCM has failed
 

Trouble Code: P0131



HO2S-11 (Bank 1 Sensor 1) Circuit Low Input

Possible Causes:



Air leaks in the exhaust system, intake manifold, vacuum lines
 
Engine misfire condition present (look for P0300 series codes)
 
Fuel system too lean (possible low fuel pressure, water in fuel)
 
HO2S signal circuit is shorted to the sensor or chassis ground
 
HO2S is damaged (i.e., cracked) or air reference hole clogged
 
MAP sensor is skewed indicating a false high vacuum condition - disconnect MAP sensor and check the HO2S for a lean signal
 
PCM has failed
 

Trouble Code: P0132



HO2S-11 (Bank 1 Sensor 1) Circuit High Input

Possible Causes:



Fuel system is too rich (fuel pressure too high, fuel pressure regulator leaking, or one or more fuel injectors sticking/leaking)
 
HO2S element is silicon, water or fuel contaminated
 
HO2S signal circuit is shorted to system power (B+)
 
HO2S signal tracking (water intrusion) in the connector causing a short between the HO2S signal and heater power circuits
 
PCM has failed
 

Trouble Code: P0133



HO2S-11 (Bank 1 Sensor 1) Insufficient Activity

Possible Causes:



HO2S heater is damaged or has failed
 
HO2S signal or ground circuit has a high resistance condition
 
HO2S signal circuit is open or shorted to system power (B+)
 
HO2S has failed (i.e., it is silicon, water or fuel contaminated)
 
PCM has failed
 

Trouble Code: P0137



HO2S-12 (Bank 1 Sensor 2) Circuit Low Input

Possible Causes:



Air leaks in the exhaust system, intake manifold, vacuum lines
 
Engine misfire condition present (look for P0300 series codes)
 
Fuel system too lean (possible low fuel pressure, water in fuel)
 
HO2S signal circuit is shorted to the sensor or chassis ground
 
HO2S is damaged (i.e., cracked) or air reference hole clogged
 
MAP sensor is skewed indicating a false high vacuum condition - disconnect MAP sensor and check the HO2S for a lean signal
 
PCM has failed
 

Trouble Code: P0138



HO2S-12 (Bank 1 Sensor 2) Circuit High Input

Possible Causes:



Fuel system is too rich (fuel pressure too high, fuel pressure regulator leaking, or one or more fuel injectors sticking/leaking)
 
HO2S element is silicon, water or fuel contaminated
 
HO2S signal circuit is shorted to system power (B+)
 
HO2S signal tracking (water intrusion) in the connector causing a short between the HO2S signal and heater power circuits
 
PCM has failed
 

Trouble Code: P0140



HO2S-12 (Bank 1 Sensor 2) Insufficient Activity

Possible Causes:



Exhaust leak present in the exhaust manifold or exhaust pipes
 
HO2S signal or ground circuit has a high resistance condition
 
HO2S element is silicon, water or fuel contaminated
 
PCM has failed
 
TSB 02-06-04-011 contains a repair procedure for this code
 

Trouble Code: P0141



HO2S-12 (Bank 1 Sensor 2) Heater Circuit Malfunction

Possible Causes:



HO2S heater ground circuit is open or has high resistance
 
HO2S heater power circuit is open (test O2S fuse in fuse block)
 
HO2S heater element is damaged or has failed
 
PCM has failed
 

Trouble Code: P0171



Fuel System Lean (Bank 1)

Possible Causes:



Air leaks in intake manifold, exhaust pipes or exhaust manifold
 
Fuel control sensor is out of calibration (ECT, IAT or MAP)
 
Low fuel pressure (fuel filter clogged, pressure regulator failure)
 
One or more injectors restricted or pressure regulator has failed
 
HO2S element is contaminated, deteriorated or has failed
 
Vacuum hose is disconnected, broken, leaking or loose
 

Trouble Code: P0172



Fuel System Rich (Bank 1)

Possible Causes:



Base engine "mechanical" fault affecting one or more cylinders
 
EVAP system component has failed or canister fuel saturated
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel system supplying too much fuel at idle speed or at cruise
 
Fuel injector(s) is leaking or stuck partially open (one or more)
 
HO2S is contaminated, deteriorated or it has failed
 

Trouble Code: P0201



Fuel Injector 1 Control Circuit Malfunction

Possible Causes:



Injector 1 control circuit is open or grounded between the injector and the PCM
 
Injector 1 power circuit is open (test INJ fuse in fuse block)
 
Injector 1 is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0202



Fuel Injector 2 Control Circuit Malfunction

Possible Causes:



Injector 2 control circuit is open or grounded between the injector and the PCM
 
Injector 2 power circuit is open (test INJ fuse in fuse block)
 
Injector 2 is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0203



Fuel Injector 3 Control Circuit Malfunction

Possible Causes:



Injector 3 control circuit is open or grounded between the injector and the PCM
 
Injector 3 power circuit is open (test INJ fuse in fuse block)
 
Injector 3 is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0204



Fuel Injector 4 Control Circuit Malfunction

Possible Causes:



Injector 4 control circuit is open or grounded between the injector and the PCM
 
Injector 4 power circuit is open (test INJ fuse in fuse block)
 
Injector 4 is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0300



Multiple Engine Misfire Detected

Possible Causes:



Base engine mechanical fault that affects one or more cylinders
 
Fuel metering fault that affects more than one cylinder
 
Fuel pressure too low or too high, fuel supply contaminated
 
EVAP system problem or the EVAP canister is fuel saturated
 
EGR valve is stuck open or PCV system has a vacuum leak
 
IC control circuit is shorted to ground (an intermittent fault)
 
Ignition system fault (a coil) that affects more than one cylinder
 
TSB 87-65-08 contains a repair procedure for this code
 
TSB 03-06-04-030 contains a repair procedure for this code
 
TSB 03-06-04-055 contains a repair procedure for this code
 

Trouble Code: P0301



Cylinder 1 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only Cylinder 1
 
Fuel delivery component fault that affects only Cylinder 1 (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects Cylinder 1
 
TSB 87-65-08 contains a repair procedure for this code
 

Trouble Code: P0302



Cylinder 2 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only Cylinder 2
 
Fuel delivery component fault that affects only Cylinder 2 (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects Cylinder 2
 
TSB 87-65-08 contains a repair procedure for this code
 

Trouble Code: P0303



Cylinder 3 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only Cylinder 3
 
Fuel delivery component fault that affects only Cylinder 3 (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects Cylinder 3
 
TSB 87-65-08 contains a repair procedure for this code
 

Trouble Code: P0304



Cylinder 4 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only Cylinder 4
 
Fuel delivery component fault that affects only Cylinder 4 (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects one cylinder
 
TSB 87-65-08 contains a repair procedure for this code
 

Trouble Code: P0325



Knock Sensor Circuit Malfunction

Possible Causes:



Knock sensor signal circuit is open, shorted to ground or power
 
Knock sensor ground circuit is open (not mounted properly)
 
Knock sensor is damaged or has failed
 
On modules with an integrated sensor, clear the codes and retest for codes. If the same code resets, the PCM has failed.
 

Trouble Code: P0336



Crankshaft Position Sensor Range/Performance

Possible Causes:



CKP sensor signal circuit is open or shorted to ground
 
CKP sensor VREF circuit is open between the sensor and PCM
 
CKP sensor ground (Low Reference) circuit is open
 
CKP sensor is damaged or it failed (check crankshaft reluctor)
 
Check for CKP sensor wiring routed to close to the plug wires
 
PCM has failed
 

Trouble Code: P0340



CMP Sensor Circuit Malfunction

Possible Causes:



CMP sensor signal circuit is open, shorted to ground or shorted to VREF between the sensor and the PCM
 
CMP sensor VREF circuit is open between sensor and PCM
 
CMP sensor ground circuit or "shielded" ground circuit is open
 
CMP sensor is cracked or damaged (check the reluctor wheel)
 
PCM has failed
 

Trouble Code: P0341



CMP Sensor Signal Range/Performance

Possible Causes:



CMP sensor signal circuit is open, shorted to ground or VREF
 
CMP sensor signal wire is routed to close to the Generator, spark plug wires or any other possible cause of EMI/RFI under the hood (check for high power receivers causing interference)
 
CMP sensor "shield" ground circuit is open (intermittent fault)
 
CMP sensor is cracked or damaged (check the reluctor wheel)
 
PCM has failed
 

Trouble Code: P0410



Secondary AIR System Performance

Possible Causes:



AIR solenoid power circuit is open (check the U/H IGN fuse)
 
AIR pump is damaged or has failed (inspect air pump for water)
 
AIR system check valves and/or pipes are damaged or leaking
 
AIR system hoses or lines are damaged, pinched or kinked
 
Base engine problem (e.g., excessive exhaust back pressure)
 
PCM has failed
 

Trouble Code: P0420



Catalyst System Low Efficiency

Possible Causes:



Air leaks at the exhaust manifold or in the exhaust pipes
 
Base engine problems (i.e., high engine oil or coolant usage)
 
Catalytic converter is damaged, contaminated or has failed
 
Continuous engine misfire conditions, or weak or low coil output
 
Front HO2S or rear HO2S is contaminated with fuel or moisture
 
Rear HO2S is loose in the mounting hole (check it for a leak)
 
Front HO2S older (aged) than the rear HO2S (HO2S-12 is lazy)
 

Trouble Code: P0440



EVAP System Malfunction

Possible Causes:



Charcoal canister is loaded with fuel or moisture
 
Fuel filler cap is loose, cross-threaded, damaged or wrong part
 
Fuel tank, fuel filler neck or fuel sending unit 'O' ring is leaking
 
Fuel tank pressure sensor is damaged, disconnected or it failed
 
Fuel tank vapor line(s) is clogged, damaged or disconnected
 
Purge valve vapor line is clogged, damaged, or disconnected
 
Purge or vent solenoid power circuit is open (check the fuse)
 
PCM has failed
 
TSB 02-06-04-044 contains a repair procedure for this code
 

Trouble Code: P0442



EVAP System Small Leak (0.040") Detected

Possible Causes:



Charcoal canister is loaded with fuel or moisture
 
Fuel filler cap is loose, cross-threaded, damaged or wrong part
 
Fuel tank, fuel filler neck or fuel sending unit 'O' ring is leaking
 
Fuel tank pressure sensor is damaged, disconnected or it failed
 
Fuel tank vapor line(s) is clogged, damaged or disconnected
 
Purge valve vapor line is clogged, damaged, or disconnected
 
Purge solenoid or Vent solenoid has a small leaking (sticking)
 
PCM has failed
 
TSB 01-06-04-007A contains a repair procedure for this code
 

Trouble Code: P0446



EVAP Vent System Performance

Possible Causes:



EVAP vent fresh air hose is clogged, kinked or restricted
 
EVAP Vent solenoid is contaminated, damaged or has failed
 
EVAP Canister plugged or severely restricted
 
Fuel Cap or EVAP Service Port leaking
 
Fuel vapor lines or purge lines damaged or leaking
 
FTP sensor is out-of-calibration, damaged or "skewed"
 
PCM has failed
 
TSB 61-65-31A contains a repair procedure for this code
 

Trouble Code: P0452



Fuel Tank Pressure Sensor Circuit Low Input

Possible Causes:



FTP sensor signal circuit is open or shorted to ground
 
FTP sensor VREF circuit is open or shorted to ground
 
FTP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0453



Fuel Tank Pressure Sensor Circuit High Input

Possible Causes:



FTP sensor signal circuit is shorted to VREF or system power
 
FTP sensor ground circuit is open between sensor and PCM
 
FTP sensor is damaged or has failed
 
PCM has failed
 

 
label.common.footer.alt.autozoneLogo