S10 Pickup, Sonoma 2000-2004

4.3L V6 VIN W N/R 2

Print

Trouble Code: P0304



Cylinder 4 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only one cylinder
 
Fuel delivery component fault that affects only one cylinder (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects one cylinder
 
TSB 00-06-04-024 contains a repair procedure for this code
 

Trouble Code: P0305



Cylinder 5 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only one cylinder
 
Fuel delivery component fault that affects only one cylinder (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects one cylinder
 
TSB 00-06-04-024 contains a repair procedure for this code
 

Trouble Code: P0306



Cylinder 6 Misfire Detected

Possible Causes:



Air leak in the intake manifold, or in the EGR or PCV system
 
Base engine mechanical fault that affects only one cylinder
 
Fuel delivery component fault that affects only one cylinder (i.e., a contaminated, dirty or sticking fuel injector)
 
Ignition system problem (coil or plug) that affects one cylinder
 
TSB 00-06-04-024 contains a repair procedure for this code
 

Trouble Code: P0325



Knock Sensor Circuit Malfunction

Possible Causes:



Knock sensor signal circuit is open, shorted to ground or power
 
Knock sensor ground circuit is open (i.e., not mounted properly)
 
Knock sensor is damaged or has failed
 
On modules with an integrated sensor, clear the codes and retest for codes. If the same code resets, the PCM has failed.
 

Trouble Code: P0339



CMP Sensor Circuit Malfunction

Possible Causes:



CMP sensor signal circuit is open or shorted to ground
 
CMP sensor VREF circuit is open between sensor and PCM
 
CMP sensor ground (Low Reference) circuit is open
 
CMP sensor is damaged or it failed (check the reluctor wheel)
 
PCM has failed
 
TSB 02-06-04-043 contains a repair procedure for this code
 

Trouble Code: P0341



CMP Sensor Signal Range/Performance

Possible Causes:



CMP sensor signal circuit is open, shorted to ground or VREF
 
CMP sensor signal wire is routed to close to the Generator, spark plug wires or any other possible cause of EMI/RFI
 
CMP sensor is cracked, damaged or has failed
 
PCM has failed
 

Trouble Code: P0401



Insufficient EGR Flow Detected

Possible Causes:



Base engine problem (e.g., a severely restricted exhaust)
 
EGR vacuum hoses damaged, loose or routed incorrectly
 
EGR passages or intake passages clogged or restricted
 
EGR solenoid valve is clogged (carbon), damaged or has failed
 

Trouble Code: P0405



EGR Position Sensor Circuit Low Input

Possible Causes:



EGR position sensor signal circuit is open
 
EGR position sensor signal circuit is shorted to ground
 
EGR position sensor VREF circuit is open or shorted to ground
 
EGR position sensor is damaged or has failed
 
PCM has failed
 
TSB 01-06-04-043 contains a repair procedure for this code
 

Trouble Code: P0410



Secondary Air System Performance

Possible Causes:



AIR solenoid power circuit is open (check the U/H IGN fuse)
 
AIR pump is damaged or has failed (inspect air pump for water)
 
AIR system check valves and/or pipes are damaged or leaking
 
AIR system hoses or lines are damaged, pinched or kinked
 
Base engine problem (e.g., excessive exhaust back pressure)
 
PCM has failed
 

Trouble Code: P0420



Catalyst System Low Efficiency (Bank 1)

Possible Causes:



Air leaks at the exhaust manifold or in the exhaust pipes
 
Base engine problems (i.e., high engine oil or coolant usage)
 
Catalytic converter is damaged, contaminated or has failed
 
Continuous engine misfire conditions, or weak or low coil output
 
Front HO2S or rear HO2S is contaminated with fuel or moisture
 
Rear HO2S is loose in the mounting hole (check it for a leak)
 
Front HO2S older (aged) than the rear HO2S (HO2S-12 is lazy)
 
TSB 81-65-37 contains a repair procedure for this code
 

Trouble Code: P0430



Catalyst System Low Efficiency (Bank 2)

Possible Causes:



Air leaks at the exhaust manifold or in the exhaust pipes
 
Base engine problems (i.e., high engine oil or coolant usage)
 
Catalytic converter is damaged, contaminated or has failed
 
Continuous engine misfire conditions, or weak or low coil output
 
Front HO2S or rear HO2S is contaminated with fuel or moisture
 
Rear HO2S is loose in the mounting hole (check it for a leak)
 

Trouble Code: P0440



EVAP System No Flow During Purge

Possible Causes:



Charcoal canister is loaded with fuel or moisture
 
Fuel filler cap is loose, cross-threaded, damaged or wrong part
 
Fuel tank, fuel filler neck or fuel sending unit 'O' ring is leaking
 
Fuel tank pressure sensor is damaged, disconnected or it failed
 
Fuel tank vapor line(s) is clogged, damaged or disconnected
 
Purge valve vapor line is clogged, damaged, or disconnected
 
Purge or vent solenoid power circuit is open (check the fuse)
 
PCM has failed
 

Trouble Code: P0442



EVAP System Small Leak (0.040") Detected

Possible Causes:



Charcoal canister is loaded with fuel or moisture
 
Fuel filler cap is loose, cross-threaded, damaged or wrong part
 
Fuel tank, fuel filler neck or fuel sending unit 'O' ring is leaking
 
Fuel tank pressure sensor is damaged, disconnected or it failed
 
Fuel tank vapor line(s) is clogged, damaged or disconnected
 
Purge valve vapor line is clogged, damaged, or disconnected
 
Purge solenoid or Vent solenoid has a small leaking (sticking)
 
PCM has failed
 

Trouble Code: P0443



EVAP Purge Solenoid Control Circuit Malfunction

Possible Causes:



Purge solenoid control circuit is open or shorted to ground
 
Purge solenoid control circuit is shorted to system power (B+)
 
Purge solenoid power circuit is open (test the ENG1 fuse)
 
Purge solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0446



EVAP Vent System Performance

Possible Causes:



EVAP vent fresh air hose is clogged, kinked or restricted
 
EVAP Vent solenoid is contaminated, damaged or has failed
 
EVAP Canister plugged or severely restricted
 
Fuel Cap or EVAP Service Port leaking
 
Fuel vapor lines or purge lines damaged or leaking
 
FTP sensor is out-of-calibration, damaged or "skewed"
 
PCM has failed
 
TSB 02-06-04-037 contains a repair procedure for this code
 

Trouble Code: P0449



EVAP Vent Solenoid Control Circuit Malfunction

Possible Causes:



Vent solenoid control circuit is open or shorted to ground
 
Vent solenoid control circuit is shorted to system power (B+)
 
Vent solenoid power circuit is open (test the ENG1 fuse)
 
Vent solenoid is damaged or has failed
 
PCM has failed
 

Trouble Code: P0452



Fuel Tank Pressure Sensor Circuit Low Input

Possible Causes:



FTP sensor connector is damaged or shorted
 
FTP sensor signal circuit is open or shorted to ground
 
FTP sensor VREF circuit is open or shorted to ground
 
FTP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0453



Fuel Tank Pressure Sensor Circuit High Input

Possible Causes:



FTP sensor connector is damaged, loose or open
 
FTP sensor signal circuit is shorted to VREF (5v)
 
FTP sensor ground circuit is open between sensor and PCM
 
FTP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0461



Fuel Level Sensor Range/Performance

Possible Causes:



Fuel level sensor signal circuit is open or shorted to ground between the fuel level sensor and the PCM connector
 
Fuel level sensor ground circuit is open or has high resistance
 
Fuel level sender is damaged, binding or not aligned properly
 
Instrument cluster or the PCM has failed
 

Trouble Code: P0462



Fuel Level Sensor Low Input

Possible Causes:



Fuel level sensor signal circuit is shorted to ground between the fuel level sensor and the PCM connector
 
Fuel level sender is damaged, binding or not aligned properly
 
PCM has failed
 

Trouble Code: P0463



Fuel Level Sensor High Input

Possible Causes:



Fuel level sensor signal circuit is shorted to system power
 
Fuel level sensor ground circuit is open
 
Fuel level sender is damaged, binding or not aligned properly
 
PCM has failed
 

Trouble Code: P0506



Idle Speed Too Low

Possible Causes:



Air inlet duct is collapsed, loose or air filter element is clogged
 
Base engine problem (i.e., compression or misfire condition)
 
IAC solenoid control circuit has a high resistance condition
 
IAC valve is damaged or has failed
 
Idle air inlet passage or throttle bore is dirty or full of deposits
 
MAF sensor is dirty, out-of-calibration or it is "skewed"
 
Throttle plate, throttle shaft or linkage is damaged or sticking
 
PCM has failed
 

Trouble Code: P0563



System Voltage Too High

Possible Causes:



Check the condition of the battery (it may be worn out)
 
Test the operation of the Generator (it may have failed)
 
Vehicle may have been used to jump-start another vehicle
 

Trouble Code: P0601



Control Module ROM Malfunction

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 
TSB 67-65-23 contains a repair procedure for this code
 

Trouble Code: P0602



Control Module Not Programmed

Possible Causes:



Reprogram the PCM with the correct software and calibration. If this step does not correct the problem, the PCM must be replaced and programmed with the correct software/calibration.
 

Trouble Code: P0603



Control Module Long Term Memory Reset

Possible Causes:



An interruption to the PCM main power and/or ground circuits
 
Check the PCM power and ground circuits and make repairs as necessary. Clear the codes and recheck. If it resets, the PCM must be replaced and programmed with the correct software.
 

Trouble Code: P0604



Control Module Random Access Memory Failure

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0605



Control Module Programming Read Only Memory

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0606



Control Module Internal Performance

Possible Causes:



The PCM must be replaced to correct this problem. A new PCM must be programmed with the correct software/calibration.
 

Trouble Code: P0621



Generator 'L' Terminal Circuit Malfunction

Possible Causes:



Generator 'L' terminal circuit is open or shorted to power (B+)
 
Generator 'F' terminal circuit is shorted to ground
 
Generator is damaged or has failed (no output)
 
PCM has failed
 

Trouble Code: P1106



MAP Sensor Circuit Intermittent High Input

Possible Causes:



MAP sensor signal circuit is shorted to VREF (intermittent fault)
 
MAP sensor ground circuit is open (intermittent fault)
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1107



MAP Sensor Circuit Intermittent Low Input

Possible Causes:



MAP sensor signal circuit shorted to ground (intermittent fault)
 
MAP sensor VREF circuit is open (intermittent fault)
 
MAP sensor is damaged or has failed (intermittent fault)
 
PCM has failed
 

Trouble Code: P1111



IAT Sensor Circuit Intermittent High Input

Possible Causes:



IAT sensor signal circuit is open (intermittent fault)
 
IAT sensor ground circuit is open (intermittent fault)
 
IAT sensor is damaged (an intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1112



IAT Sensor Circuit Intermittent Low Input

Possible Causes:



IAT sensor signal circuit is shorted to ground (intermittent fault)
 
IAT sensor is damaged (an intermittent "shorted" condition)
 
PCM has failed
 

Trouble Code: P1114



ECT Sensor Circuit Intermittent Low Input

Possible Causes:



ECT sensor signal circuit shorted to ground (intermittent fault)
 
ECT sensor has failed (possible intermittent shorted condition)
 
PCM has failed
 

Trouble Code: P1115



ECT Sensor Circuit Intermittent High Input

Possible Causes:



ECT sensor signal circuit is open between the sensor and PCM
 
ECT sensor ground circuit is open between sensor and PCM
 
ECT sensor has failed (possible intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1121



TP Sensor Circuit High Input (Intermittent)

Possible Causes:



TP sensor signal circuit is shorted to VREF (intermittent fault)
 
TP sensor ground circuit is open (an intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent open)
 
PCM has failed
 

Trouble Code: P1122



TP Sensor Circuit Intermittent Low Input

Possible Causes:



TP sensor signal circuit is shorted to ground (intermittent fault)
 
TP sensor VREF circuit is open or grounded (intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent short)
 
PCM has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

 
label.common.footer.alt.autozoneLogo