S10 Pickup, Sonoma 2000-2004

4.3L V6 VIN X Std 3

Print

Trouble Code: P1121



TP Sensor Circuit High Input (Intermittent)

Possible Causes:



TP sensor signal circuit is shorted to VREF (intermittent fault)
 
TP sensor ground circuit is open (an intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent open)
 
PCM has failed
 

Trouble Code: P1122



TP Sensor Circuit Intermittent High Input

Possible Causes:



TP sensor signal circuit is shorted to VREF (intermittent fault)
 
TP sensor ground circuit is open (an intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent open)
 
PCM has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1153



HO2S-21 (Bank 2 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
MAP sensor or TP sensor is out-of-calibration or "skewed"
 
PCM has failed
 

Trouble Code: P1154



HO2S-21 (Bank 2 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158ºF (70ºC). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test rpm (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (rpm) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

Trouble Code: P1380



Misfire Detected, Rough Road Data Not Available

Possible Causes:



Use the Freeze Frame/Failure Records data to help find the cause on an intermittent fault. If the code cannot be duplicated, the data in the Freeze Frame/Failure Records can determine how many miles since the code set. The Fail Counter and Pass Counter can also help determine how many ignition cycles the diagnostic reported a pass or a fail. Operate the vehicle within the Freeze Frame conditions (i.e., load, engine and vehicle speed, temperature etc.). This will isolate when the code set.
 
Service the ABS before diagnosing a misfire because an actual engine misfire may or may not exist. An actual engine misfire may have occurred during an ABS malfunction.
 
Determine if the vehicle was driven on a rough road, and the ABS could not detect this due to a malfunction. The PCM may interpret variations in crankshaft speed caused by the rough road as a misfire without an actual engine misfire present.
 
Refer to Diagnostic System Check for Antilock Brake System
 
Refer to Diagnostic System Check for the Engine Controls
 

Trouble Code: P1381



Misfire Detected - No Communication With The EBCM

Possible Causes:



Service the ABS before diagnosing a misfire because an actual engine misfire may not exist. Also, an actual engine misfire may have occurred during a period of ABS fault.
 
Determine if the vehicle was driven on a rough road, and the ABS could not detect this due to a malfunction. The PCM may interpret variations in crankshaft speed caused by the rough road as a misfire without an actual engine misfire present.
 
Refer to Diagnostic System Check for Antilock Brake System
 
Refer to Diagnostic System Check for the Engine Controls
 

Trouble Code: P1415



Secondary Air Injection System (Bank 1) Malfunction

Possible Causes:



Air hoses disconnected, loose, kinked or failed (a burnt hose)
 
AIR pump is damaged or has failed (inspect air pump for water)
 
AIR system check valves and/or pipes are damaged or leaking
 
PCM has failed
 

Trouble Code: P1416



Secondary Air Injection System (Bank 2) Malfunction

Possible Causes:



Air hoses disconnected, loose, kinked or failed (a burnt hose)
 
AIR pump is damaged or has failed (inspect air pump for water)
 
AIR system check valves and/or pipes are damaged or leaking
 
PCM has failed
 

Trouble Code: P1441



EVAP System Flow During Non-Purge

Possible Causes:



An improperly installed or damaged EVAP canister purge valve
 
A temporary blockage in the EVAP canister purge valve, purge pipe, or EVAP canister could cause an intermittent condition
 
FTP sensor is out-of-calibration, damaged or "skewed"
 
Purge solenoid valve is damaged or has failed
 
PCM has failed
 

Trouble Code: P1621



Control Module Long Term Memory Performance

Possible Causes:



Serial data circuit is open between VCM and VTD (Passlock) control module, or serial data circuit is shorted to ground or B+
 
Perform the Theft Deterrent System Check
 
Perform the Powertrain Onboard Diagnostic System Check
 

Trouble Code: P1631



Theft Deterrent - Start Enable Signal Not Correct

Possible Causes:



Refer to Diagnostic System Check for Theft Deterrent Module
 
Perform the Powertrain Onboard Diagnostic System Check
 
TSB 77-65-31 contains a repair procedure for this code
 

Trouble Code: P1635



5-Volt Reference 1 Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to sensor ground or chassis ground
 
5v VREF circuit, MAP or EOP sensor circuit is shorted to (B+)
 
5v VREF circuit shorted to EGR sensor High signal circuit
 
EGR solenoid valve (and sensor) is damaged or has failed
 
PCM has failed
 

Trouble Code: P1639



5-Volt Reference 2 Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to sensor ground or chassis ground
 
5v VREF circuit or FTP sensor circuit is shorted to (B+)
 
5v VREF circuit shorted to the FTP sensor signal circuit
 
FTP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: U1000



Class 2 Communication Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
SDM (module) could be shorted pulling the voltage low
 

Trouble Code: U1016



No Communication With Powertrain Control Module

Possible Causes:



PCM Class 2 circuit is open, shorted to ground or to B+
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 
PCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1026



Loss of ATC Class 2 Communication

Possible Causes:



Check for a loose connection at the ATC module
 
Test the main power and ground circuits to the ATC module
 
Check the Class 2 serial data circuit to the ATC module
 
ATC module may have failed
 

Trouble Code: U1041



Loss of Electronic Brake Controller Communication

Possible Causes:



Check for a loose connection at the EBCM (module)
 
Test the main power and ground circuits to the EBCM (module)
 
Check the Class 2 serial data circuit to the EBCM (module)
 
EBCM (module) may have failed
 

Trouble Code: U1048



No Communication With Rear Wheel Steering Control Module

Possible Causes:



RWSCM Class 2 circuit is open, shorted to ground or to B+
 
RWSCM ignition power circuit has a high resistance condition
 
RESCM main ground circuit(s) has a high resistance condition
 
RESCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1064



No Communication With Body Control Module

Possible Causes:



BCM Class 2 circuit is open, shorted to ground or to B+
 
BCM ignition power circuit has a high resistance condition
 
BCM main ground circuit(s) has a high resistance condition
 
BCM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1088



No Communication With SDM (Restraint Module)

Possible Causes:



SDM Class 2 circuit is open, shorted to ground or to B+
 
SDM ignition power circuit has a high resistance condition
 
SDM main ground circuit(s) has a high resistance condition
 
SDM (module) may have failed and is pulling the circuit low
 

Trouble Code: U1096



No Communication With Instrument Panel Cluster

Possible Causes:



IPC Class 2 circuit is open, shorted to ground or to B+
 
IPC ignition power circuit has a high resistance condition
 
IPC main ground circuit(s) has a high resistance condition
 
IPC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1097



No Communication With Driver Information Center

Possible Causes:



DIC Class 2 circuit is open, shorted to ground or to B+
 
DIC ignition power circuit has a high resistance condition
 
DIC main ground circuit(s) has a high resistance condition
 
DIC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1151



No Communication With Vehicle Interface Unit

Possible Causes:



VIU Class 2 circuit is open, shorted to ground or to B+
 
VIU ignition power circuit has a high resistance condition
 
VIU main ground circuit(s) has a high resistance condition
 
VIU (module) may have failed and is pulling the circuit low
 

Trouble Code: U1152



No Communication With HVAC Control Module

Possible Causes:



HVAC Class 2 circuit is open, shorted to ground or to B+
 
HVAC ignition power circuit has a high resistance condition
 
HVAC main ground circuit(s) has a high resistance condition
 
HVAC (module) may have failed and is pulling the circuit low
 

Trouble Code: U1193



Loss of Vehicle Immobilizer Module Communications

Possible Causes:



Test the main power and ground circuits to the VIM module for a loose connection
 
Check the Class 2 serial data circuit to the VIM module
 
VTD module may have failed
 

Trouble Code: U1255



Class 2 Communications Malfunction

Possible Causes:



Class 2 circuit is open, shorted to ground or shorted to power
 
PCM ignition power circuit(s) has a high resistance condition
 
PCM main ground circuit(s) has a high resistance condition
 

Trouble Code: U1305



Class 2 Data Link High or Low

Possible Causes:



Class 2 serial data line has either a high or low voltage condition on the circuit, and the module cannot identify the fault
 
One or more modules on Class 2 line has an short to power
 
One or more modules on the Class 2 line has a short to ground
 

 
label.common.footer.alt.autozoneLogo