Log In
Search suggestions

    My Vehicles

    1983 Nissan/Datsun 200SX 2.2L FI 4cyl

    My Store

    1720 S RIDGEWOOD A
    (386) 427-1210

    CLOSED Open at 7:30 AM

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    S10 Pickup, Sonoma 2000-2004

    Removal & Installation

    Print

    4.3L Engine



    1. Disconnect the negative battery cable.
    2.  
    3. Place a drain pan under the vehicle.
    4.  
    5. Remove the air cleaner assembly.
    6.  
    7. Remove the power steering pump pulley.
    8.  
    9. Disconnect the power steering cooler hose from the power steering pump.
    10.  
    11. Disconnect the power steering pressure hose from the power steering gear.
    12.  
    13. Disconnect the air reacter tube from the lower reacter tube.
    14.  
    15. Remove the air reacter pipe lower retaining nut.
    16.  
    17. Disconnect the air reactor pipe from the check valve and remove reacter pipe.
    18.  
    19. Remove the power steering pump filler neck tube mounting bolt.
    20.  
    21. Remove the power steering pump filler neck tube.
    22.  
    23. Remove the power steering rear mounting bracket nut from the engine stud.
    24.  
    25. Remove the power steering pump front mounting bolts.
    26.  
    27. Loosen the accessory mounting bracket bolts and nuts and pull accessory mounting bracket forward.
    28.  
    29. Remove the power steering pump and power steering pressure hose from the vehicle. Note the position of the power steering pressure hose to the power steering pump to ensure proper installation to the vehicle.
    30.  
    31. Remove the power steering pressure hose from the power steering pump.

      Click image to see an enlarged view

      Fig. Power steering pump mounting location underneath A/C compressor-4.3L engine

    32.  

    To install:

    1. Install the power steering pressure hose to the power steering pump and tighten to 18 ft. lbs. (25 Nm).
    2.  
    3. Install the power steering pump and power steering pressure hose to the vehicle.
    4.  
    5. Reposition the accessory mounting bracket and tighten the accessory mounting bracket mounting bolts and nut to 37 ft. lbs. (50 Nm).
    6.  
    7. Install the power steering pump front mounting bolts and tighten to 37 ft. lbs. (50 Nm).
    8.  
    9. Install the power steering pump rear mounting bracket nut to the engine stud and tighten to 31 ft. lbs. (41 Nm).
    10.  
    11. Install the filler neck tube.
    12.  
    13. Install the filler neck tube mounting bolt and tighten to 15 ft. lbs. (20 Nm).
    14.  
    15. Connect the lower secondary air injection reactor pipe to the check valve.
    16.  
    17. Install the lower secondary air injection reactor pipe bracket to the power steering pump bracket stud.
    18.  
    19. Install the power steering pump mounting bracket retaining nut and tighten to 31 ft. lbs. (41 Nm).
    20.  
    21. Connect the lower secondary air injection reactor pipe lower connection.
    22.  
    23. Connect the power steering cooler hose to the power steering pump.
    24.  
    25. Connect the power steering pressure hose to the power steering gear and tighten to 22 ft. lbs. (30 Nm).
    26.  
    27. Install the power steering pump pulley.
    28.  
    29. Install the air cleaner assembly.
    30.  
    31. Remove the drain pan from under the vehicle.
    32.  
    33. Fill the power steering system.
    34.  
    35. Bleed the system.
    36.  
    37. Inspect the hoses for clearance away from the frame and other components.
    38.  
    39. Connect the negative battery cable.
    40.  

     
    AutoZone Logo