SRX 2004-2005

Disarming & Arming

Print

The Supplemental Restraint System (SRS) is designed to work in conjunction with the standard 3-point safety belts to reduce injury in a head-on collision.


CAUTION
The SRS can actually cause physical injury or death if the safety belts are not used, or if the manufacturer-s warnings are not followed.

The SRS is comprised of the following components:



Driver-s side air bag module
 
Passenger-s side air bag module
 
Right-hand and left-hand primary crash front air bag sensors
 
Air bag diagnostic monitor computer
 
Electrical wiring
 

The SRS primary crash front air bag sensors are hard-wired to the air bag modules and determine when the air bags are deployed. During a frontal collision, the sensors quickly inflate the 2 air bags to reduce injury by cushioning the driver and front passenger from striking the dashboard, windshield, steering wheel and any other hard surfaces. The air bag inflates so quickly (in a fraction of a second) that in most cases it is fully inflated before you actually start to move during a collision.

Since the SRS is a complicated and essentially important system, its components are constantly being tested by a diagnostic computer. The computer illuminates the air bag indicator light on the instrument cluster for approximately 6 seconds when the ignition switch is turned to the RUN position when the SRS is functioning properly. After being illuminated for the 6 seconds, the indicator light should then turn off.

If the air bag light does not illuminate at all, stays on continuously, or flashes at any time, a problem has been detected by the diagnostic computer.


CAUTION
If at any time the air bag light indicates that the computer has noted a problem, immediately diagnose the problem. A faulty SRS can cause severe physical injury or death.

The Supplemental Restraint System (SRS) is designed to work in conjunction with the standard 3-point safety belts to reduce injury in a head-on collision.


CAUTION
The SRS can actually cause physical injury or death if the safety belts are not used, or if the manufacturer-s warnings are not followed. The manufacturer-s warnings can be found in your owner-s manual, or, in some cases, on your sun visor.

The SRS is comprised of the following components:



Driver-s side air bag module
 
Passenger-s side air bag module
 
Right-hand and left-hand primary crash front air bag sensors
 
Air bag diagnostic monitor computer
 
Electrical wiring
 

The SRS primary crash front air bag sensors are hard-wired to the air bag modules and determine when the air bags are deployed. During a frontal collision, the sensors quickly inflate the 2 air bags to reduce injury by cushioning the driver and front passenger from striking the dashboard, windshield, steering wheel and any other hard surfaces. The air bag inflates so quickly (in a fraction of a second) that in most cases it is fully inflated before you actually start to move during a collision.

Since the SRS is a complicated and essentially important system, its components are constantly being tested by a diagnostic computer. The computer illuminates the air bag indicator light on the instrument cluster for approximately 6 seconds when the ignition switch is turned to the RUN position when the SRS is functioning properly. After being illuminated for the 6 seconds, the indicator light should then turn off.

If the air bag light does not illuminate at all, stays on continuously, or flashes at any time, a problem has been detected by the diagnostic computer.


CAUTION
If at any time the air bag light indicates that the computer has noted a problem, immediately diagnose the problem. A faulty SRS can cause severe physical injury or death.

Zone 1



  1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the right rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Open front hood, and locate both front end sensors (3, 4).
  16.  
  17. Remove both connector position assurance (CPA) (1, 6) from left and right front end sensor connectors (2, 5).
  18.  
  19. Remove both connectors (2, 5) from left and right front end sensors (3, 4).

    Click image to see an enlarged view

    Fig. Front end sensors

  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect both connectors (2, 5) to the left and right front end sensors (3, 4).
  4.  
  5. Install both CPAs (1, 6) to the left and right front end sensor connectors (2, 5).
  6.  
  7. Close front hood.
  8.  
  9. Install the SIR fuse into the right rear fuse center.
  10.  
  11. Install the right rear fuse center cover.
  12.  
  13. Position the carpet back under the right rear seat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

  1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the right rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Open front hood, and locate both front end sensors (3, 4).
  16.  
  17. Remove both connector position assurance (CPA) (1, 6) from left and right front end sensor connectors (2, 5).
  18.  
  19. Remove both connectors (2, 5) from left and right front end sensors (3, 4).

    Click image to see an enlarged view

    Fig. Front end sensors

  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect both connectors (2, 5) to the left and right front end sensors (3, 4).
  4.  
  5. Install both CPAs (1, 6) to the left and right front end sensor connectors (2, 5).
  6.  
  7. Close front hood.
  8.  
  9. Install the SIR fuse into the right rear fuse center.
  10.  
  11. Install the right rear fuse center cover.
  12.  
  13. Position the carpet back under the right rear seat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

Zone 2



  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center (1) will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. When disabling the roof rail module, go to step 9. If the side impact sensor (SIS) needs disabling, go to step 12.
  16.  
  17. Remove the left carpet retainer trim.
  18.  
  19. Remove the connector position assurance (CPA)  from the left/driver roof rail module yellow connector.
  20.  
  21. Disconnect the left roof rail module connector from the left roof rail module.

    Click image to see an enlarged view

    Fig. Left side impact sensor

  22.  
  23. Remove the left center pillar trim panel.
  24.  
  25. Remove the SIS CPA (1) from the left SIS connector (2).
  26.  
  27. Remove the SIS connector (2) from the SIS (3).
  28.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS, proceed to step 3. If the roof rail module needs enabling, go to step 6.
  4.  
  5. Connect the SIS connector to the SIS.
  6.  
  7. Connect the CPA to the SIS connector.
  8.  
  9. Install the left center pillar trim panel.
  10.  
  11. Connect the roof rail module yellow connector to the left roof rail module.
  12.  
  13. Install the CPA to the left roof rail module connector.
  14.  
  15. Install the left carpet retainer trim.
  16.  
  17. Install the SIR fuse into the right rear fuse center.
  18.  
  19. Install the right rear fuse center cover.
  20.  
  21. Position the carpet back under the right rear seat.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center (1) will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. When disabling the roof rail module, go to step 9. If the side impact sensor (SIS) needs disabling, go to step 12.
  16.  
  17. Remove the left carpet retainer trim.
  18.  
  19. Remove the connector position assurance (CPA)  from the left/driver roof rail module yellow connector.
  20.  
  21. Disconnect the left roof rail module connector from the left roof rail module.

    Click image to see an enlarged view

    Fig. Left side impact sensor

  22.  
  23. Remove the left center pillar trim panel.
  24.  
  25. Remove the SIS CPA (1) from the left SIS connector (2).
  26.  
  27. Remove the SIS connector (2) from the SIS (3).
  28.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS, proceed to step 3. If the roof rail module needs enabling, go to step 6.
  4.  
  5. Connect the SIS connector to the SIS.
  6.  
  7. Connect the CPA to the SIS connector.
  8.  
  9. Install the left center pillar trim panel.
  10.  
  11. Connect the roof rail module yellow connector to the left roof rail module.
  12.  
  13. Install the CPA to the left roof rail module connector.
  14.  
  15. Install the left carpet retainer trim.
  16.  
  17. Install the SIR fuse into the right rear fuse center.
  18.  
  19. Install the right rear fuse center cover.
  20.  
  21. Position the carpet back under the right rear seat.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

Zone 3



  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove the left/driver sound insulator from the instrument panel (I/P).
  16.  
  17. Remove the connector position assurance (CPA) from the steering wheel module coil yellow connector.
  18.  
  19. Disconnect the steering wheel module coil yellow connector from the vehicle harness yellow connector.
  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the steering wheel module coil yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install the CPA to the steering wheel module coil yellow connector.
  6.  
  7. Install the left sound insulator to the I/P.
  8.  
  9. Install the SIR fuse into the right rear fuse center.
  10.  
  11. Install the right rear fuse center cover.
  12.  
  13. Position the carpet back under the right rear seat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove the left/driver sound insulator from the instrument panel (I/P).
  16.  
  17. Remove the connector position assurance (CPA) from the steering wheel module coil yellow connector.
  18.  
  19. Disconnect the steering wheel module coil yellow connector from the vehicle harness yellow connector.
  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the steering wheel module coil yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install the CPA to the steering wheel module coil yellow connector.
  6.  
  7. Install the left sound insulator to the I/P.
  8.  
  9. Install the SIR fuse into the right rear fuse center.
  10.  
  11. Install the right rear fuse center cover.
  12.  
  13. Position the carpet back under the right rear seat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

Zone 5



  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove the right/passenger sound insulator from the instrument panel (I/P).
  16.  
  17. Remove the connector position assurance (CPA) from the I/P module yellow connector.
  18.  
  19. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  20.  

Enabling procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install the CPA to the I/P module yellow connector.
  6.  
  7. Install the right sound insulator to the I/P.
  8.  
  9. Install the SIR fuse into the right rear fuse center.
  10.  
  11. Install the right rear fuse center cover.
  12.  
  13. Position the carpet back under the right rear seat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove the right/passenger sound insulator from the instrument panel (I/P).
  16.  
  17. Remove the connector position assurance (CPA) from the I/P module yellow connector.
  18.  
  19. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  20.  

Enabling procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install the CPA to the I/P module yellow connector.
  6.  
  7. Install the right sound insulator to the I/P.
  8.  
  9. Install the SIR fuse into the right rear fuse center.
  10.  
  11. Install the right rear fuse center cover.
  12.  
  13. Position the carpet back under the right rear seat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

Zone 6



  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. When disabling the roof rail module, go to step 9. If the side impact sensor (SIS) needs disabling, go to step 12.
  16.  
  17. Remove the right carpet retainer trim.

    Click image to see an enlarged view

    Fig. Right/passenger roof rail module

  18.  
  19. Remove the connector position assurance (CPA) (2) from the right/passenger roof rail module yellow connector (3).
  20.  
  21. Disconnect the right roof rail module connector from the right roof rail module (1).
  22.  
  23. Remove the right center pillar trim panel.
  24.  
  25. Remove the SIS CPA from the left SIS connector.
  26.  
  27. Remove the SIS connector from the SIS.
  28.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS, proceed to step 3. If the roof rail module needs enabling, go to step 6.
  4.  
  5. Connect the SIS connector to the SIS.
  6.  
  7. Connect the CPA to the SIS connector.
  8.  
  9. Install the right center pillar trim panel.
  10.  
  11. Connect the roof rail module yellow connector to the right roof rail module.
  12.  
  13. Install the CPA to the right roof rail module connector.
  14.  
  15. Install the right carpet retainer trim.
  16.  
  17. Install the SIR fuse into the right rear fuse center.
  18.  
  19. Install the right rear fuse center cover.
  20.  
  21. Position the carpet back under the right rear seat.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. When disabling the roof rail module, go to step 9. If the side impact sensor (SIS) needs disabling, go to step 12.
  16.  
  17. Remove the right carpet retainer trim.

    Click image to see an enlarged view

    Fig. Right/passenger roof rail module

  18.  
  19. Remove the connector position assurance (CPA) (2) from the right/passenger roof rail module yellow connector (3).
  20.  
  21. Disconnect the right roof rail module connector from the right roof rail module (1).
  22.  
  23. Remove the right center pillar trim panel.
  24.  
  25. Remove the SIS CPA from the left SIS connector.
  26.  
  27. Remove the SIS connector from the SIS.
  28.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS, proceed to step 3. If the roof rail module needs enabling, go to step 6.
  4.  
  5. Connect the SIS connector to the SIS.
  6.  
  7. Connect the CPA to the SIS connector.
  8.  
  9. Install the right center pillar trim panel.
  10.  
  11. Connect the roof rail module yellow connector to the right roof rail module.
  12.  
  13. Install the CPA to the right roof rail module connector.
  14.  
  15. Install the right carpet retainer trim.
  16.  
  17. Install the SIR fuse into the right rear fuse center.
  18.  
  19. Install the right rear fuse center cover.
  20.  
  21. Position the carpet back under the right rear seat.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

Zone 7



  1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove both connector position assurance (CPA) from the LF/driver-s side impact module and seat belt pretensioner yellow connector (1) which is located under the front of driver-s seat.

    Click image to see an enlarged view

    Fig. LF/driver-s side impact module

  16.  
  17. Disconnect the LF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  18.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the LF side impact module and pretensioner yellow connector (1) to the vehicle harness yellow connector.
  4.  
  5. Install both CPA locks to the LF side impact module and pretensioner yellow connector.
  6.  
  7. Install the SIR fuse into the right rear fuse center.
  8.  
  9. Install the right rear fuse center cover.
  10.  
  11. Position the carpet back under the right rear seat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

  1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove both connector position assurance (CPA) from the LF/driver-s side impact module and seat belt pretensioner yellow connector (1) which is located under the front of driver-s seat.

    Click image to see an enlarged view

    Fig. LF/driver-s side impact module

  16.  
  17. Disconnect the LF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  18.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the LF side impact module and pretensioner yellow connector (1) to the vehicle harness yellow connector.
  4.  
  5. Install both CPA locks to the LF side impact module and pretensioner yellow connector.
  6.  
  7. Install the SIR fuse into the right rear fuse center.
  8.  
  9. Install the right rear fuse center cover.
  10.  
  11. Position the carpet back under the right rear seat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 8



  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove the right carpet retainer trim.
  16.  
  17. Remove the connector position assurance (CPA) from the right/passenger roof rail module yellow connector.
  18.  
  19. Disconnect the right roof rail module connector from the right roof rail module.
  20.  
  21. Remove the right/passenger sound insulator from the instrument panel (I/P).
  22.  
  23. Remove the CPA from the I/P module yellow connector.
  24.  
  25. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  26.  
  27. Remove both CPA locks from the passenger/RF side impact module and seat belt pretensioner yellow connector located under the front of passenger seat.
  28.  
  29. Disconnect the RF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  30.  
  31. Remove the driver/left sound insulator from the I/P.
  32.  
  33. Remove the CPA from the steering wheel module coil yellow connector.
  34.  
  35. Disconnect the steering wheel module coil yellow connector from the vehicle harness yellow connector.
  36.  
  37. Remove both CPA locks from the driver/LF side impact module and seat belt pretensioner yellow connector located under the front of driver seat.
  38.  
  39. Disconnect the LF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  40.  
  41. Remove the left carpet retainer trim.
  42.  
  43. Remove the CPA from the left/driver roof rail module yellow connector.
  44.  
  45. Disconnect the left roof rail module connector from the left roof rail module.
  46.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the roof rail module yellow connector to the left roof rail module.
  4.  
  5. Install the CPA to the left roof rail module connector.
  6.  
  7. Install the left carpet retainer trim.
  8.  
  9. Connect the driver/LF side impact module and seat belt pretensioner yellow connector to the vehicle harness yellow connector located under the front of driver seat.
  10.  
  11. Install both CPA locks to the LF side impact module and pretensioner yellow connector.
  12.  
  13. Connect the steering wheel module coil yellow connector to the vehicle harness yellow connector.
  14.  
  15. Install the CPA to the steering wheel module coil yellow connector.
  16.  
  17. Install the driver/left sound insulator to the I/P.
  18.  
  19. Connect the passenger/I/P module yellow connector to the vehicle harness yellow connector.
  20.  
  21. Install the CPA to the I/P module yellow connector.
  22.  
  23. Install the passenger/right sound insulator to the I/P.
  24.  
  25. Connect the passenger/RF side impact module and seat belt pretensioner yellow connector to the vehicle harness yellow connector located under the front of passenger seat.
  26.  
  27. Install both CPA locks to the RF side impact module and pretensioner yellow connector.
  28.  
  29. Connect the roof rail module yellow connector to the right roof rail module.
  30.  
  31. Install the CPA to the right roof rail module connector.
  32.  
  33. Install the right carpet retainer trim.
  34.  
  35. Install the SIR fuse into the right rear fuse center.
  36.  
  37. Install the right rear fuse center cover.
  38.  
  39. Position the carpet back under the right rear seat.
  40.  
  41. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  42.  

  1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove the right carpet retainer trim.
  16.  
  17. Remove the connector position assurance (CPA) from the right/passenger roof rail module yellow connector.
  18.  
  19. Disconnect the right roof rail module connector from the right roof rail module.
  20.  
  21. Remove the right/passenger sound insulator from the instrument panel (I/P).
  22.  
  23. Remove the CPA from the I/P module yellow connector.
  24.  
  25. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  26.  
  27. Remove both CPA locks from the passenger/RF side impact module and seat belt pretensioner yellow connector located under the front of passenger seat.
  28.  
  29. Disconnect the RF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  30.  
  31. Remove the driver/left sound insulator from the I/P.
  32.  
  33. Remove the CPA from the steering wheel module coil yellow connector.
  34.  
  35. Disconnect the steering wheel module coil yellow connector from the vehicle harness yellow connector.
  36.  
  37. Remove both CPA locks from the driver/LF side impact module and seat belt pretensioner yellow connector located under the front of driver seat.
  38.  
  39. Disconnect the LF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  40.  
  41. Remove the left carpet retainer trim.
  42.  
  43. Remove the CPA from the left/driver roof rail module yellow connector.
  44.  
  45. Disconnect the left roof rail module connector from the left roof rail module.
  46.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the roof rail module yellow connector to the left roof rail module.
  4.  
  5. Install the CPA to the left roof rail module connector.
  6.  
  7. Install the left carpet retainer trim.
  8.  
  9. Connect the driver/LF side impact module and seat belt pretensioner yellow connector to the vehicle harness yellow connector located under the front of driver seat.
  10.  
  11. Install both CPA locks to the LF side impact module and pretensioner yellow connector.
  12.  
  13. Connect the steering wheel module coil yellow connector to the vehicle harness yellow connector.
  14.  
  15. Install the CPA to the steering wheel module coil yellow connector.
  16.  
  17. Install the driver/left sound insulator to the I/P.
  18.  
  19. Connect the passenger/I/P module yellow connector to the vehicle harness yellow connector.
  20.  
  21. Install the CPA to the I/P module yellow connector.
  22.  
  23. Install the passenger/right sound insulator to the I/P.
  24.  
  25. Connect the passenger/RF side impact module and seat belt pretensioner yellow connector to the vehicle harness yellow connector located under the front of passenger seat.
  26.  
  27. Install both CPA locks to the RF side impact module and pretensioner yellow connector.
  28.  
  29. Connect the roof rail module yellow connector to the right roof rail module.
  30.  
  31. Install the CPA to the right roof rail module connector.
  32.  
  33. Install the right carpet retainer trim.
  34.  
  35. Install the SIR fuse into the right rear fuse center.
  36.  
  37. Install the right rear fuse center cover.
  38.  
  39. Position the carpet back under the right rear seat.
  40.  
  41. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  42.  

Zone 9



  1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove both connector position assurance (CPA) from the RF/passenger side impact module and seat belt pretensioner yellow connector which is located under the front of passenger seat.
  16.  
  17. Disconnect the RF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  18.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the RF side impact module and pretensioner yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install both CPA locks to the RF side impact module and pretensioner yellow connector.
  6.  
  7. Install the SIR fuse into the right rear fuse center.
  8.  
  9. Install the right rear fuse center cover.
  10.  
  11. Position the carpet back under the right rear seat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

  1. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  2.  
  3. Turn the ignition switch to the OFF position.
  4.  
  5. Remove the key from the ignition switch.
  6.  
  7. Adjust the right rear seat to the rear of vehicle.
  8.  
  9. Pull the carpet away from under the right side of rear seat.
  10.  
  11. When the carpet is pulled away from the rear seat the right rear fuse center will be exposed, then remove the fuse center top cover.
    NOTE
    With the SIR fuse removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  12.  
  13. Locate and remove the SIR fuse from the right rear fuse center.
  14.  
  15. Remove both connector position assurance (CPA) from the RF/passenger side impact module and seat belt pretensioner yellow connector which is located under the front of passenger seat.
  16.  
  17. Disconnect the RF side impact module and pretensioner yellow connector from the vehicle harness yellow connector.
  18.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the RF side impact module and pretensioner yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install both CPA locks to the RF side impact module and pretensioner yellow connector.
  6.  
  7. Install the SIR fuse into the right rear fuse center.
  8.  
  9. Install the right rear fuse center cover.
  10.  
  11. Position the carpet back under the right rear seat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

 
label.common.footer.alt.autozoneLogo