SRX 2004-2005

Removal & Installation

Print

  1. Drain the cooling system to a level below the ECT sensor.
  2.  
  3. Unplug the harness connector from the ECT sensor.
  4.  
  5. Remove the ECT sensor from the engine.
  6.  
  7. Installation is the reverse of removal. If reusing the old sensor, coat the threads with GM sealant 12346004 or equivalent. New sensors are already coated; additional sealant is not needed. Tighten the sensor to 16 ft. lbs. (22 Nm) on 3.6L engines or 15 ft. lbs. (20 Nm) on 4.6L engines.

    Click image to see an enlarged view

    Fig. ECT sensor mounting-3.6L engine



    Click image to see an enlarged view

    Fig. ECT sensor mounting-4.6L engine

  8.  

3.6L Engine




CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the ignition OFF .
  4.  
  5. Remove the coolant temperature sensor electrical connector.
  6.  
  7. Remove the coolant temperature sensor.

    Click image to see an enlarged view

    Fig. Coolant temperature sensor-3.6L engine

  8.  

To install:

  1. Install the coolant temperature sensor tighten to 16 ft. lbs (22 Nm).
  2.  
  3. Install the coolant temperature sensor electrical connector.
  4.  
  5. Inspect and fill the cooling system as necessary.
  6.  


CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the ignition OFF .
  4.  
  5. Remove the coolant temperature sensor electrical connector.
  6.  
  7. Remove the coolant temperature sensor.

    Click image to see an enlarged view

    Fig. Coolant temperature sensor-3.6L engine

  8.  

To install:

  1. Install the coolant temperature sensor tighten to 16 ft. lbs. (22 Nm).
  2.  
  3. Install the coolant temperature sensor electrical connector.
  4.  
  5. Inspect and fill the cooling system as necessary.
  6.  

4.6L Engines




CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn OFF the ignition
  4.  
  5. Remove the fuel injector sight shield.
  6.  
  7. Drain the coolant to below the level of the engine coolant temperature (ECT) sensor.
  8.  
  9. Disconnect the ECT sensor harness connector.
  10.  
  11. Remove the ECT sensor.

    Click image to see an enlarged view

    Fig. Coolant temperature sensor-4.6L engine

  12.  

To install:


WARNING
Notice: Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.

  1. Coat the sensor threads with sealer GM P/N 1050805, or equivalent.
  2.  
  3. Install the ECT sensor and tighten to 15 ft. lbs. (20 Nm).
  4.  
  5. Connect the ECT sensor harness connector.
  6.  
  7. Install the fuel injector sight shield.
  8.  
  9. Refill the coolant system.
  10.  

 
label.common.footer.alt.autozoneLogo