SRX 2004-2005

Ignition Switch

Print

Removal & Installation




CAUTION
Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in the Chassis Electrical Section.
  2.  
  3. Remove the upper and lower trim covers.
  4.  
  5. Remove the theft deterrent control module (2) from the ignition lock cylinder case (1).

    Click image to see an enlarged view

    Fig. Deterrent module (2) and cylinder lock case (1)



    Click image to see an enlarged view

    Fig. Ignition switch assembly (1) and mounting screws (2)

  6.  
  7. Disconnect the connector located by the ignition switch.
  8.  
  9. Remove the 2 tapping screws (2) from the ignition switch assembly (1).
  10.  
  11. Remove the ignition switch (1) from the ignition lock cylinder case.
  12.  

To install:

  1. Install the ignition switch (1) and secure by using the 2 tapping screws (2) and tighten to 62 inch lbs. (7 Nm).

    Click image to see an enlarged view

    Fig. Ignition switch assembly (1) and mounting screws (2)

  2.  
  3. Connect the connector to the ignition switch.
  4.  
  5. Install the theft deterrent control module (2) onto the ignition lock cylinder case (1).

    Click image to see an enlarged view

    Fig. Deterrent module (2) and cylinder lock case (1)

  6.  
  7. Install the upper and lower trim covers.
  8.  
  9. Enable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR.
  10.  


CAUTION
When performing service around the SIR system components or wiring, the SIR system MUST be disabled. Failure to do so could result in possible air bag deployment, personal injury or unneeded SIR system repairs.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in the Chassis Electrical Section.
  2.  
  3. Remove the upper and lower trim covers.
  4.  
  5. Remove the theft deterrent control module (2) from the ignition lock cylinder case (1).

    Click image to see an enlarged view

    Fig. Deterrent module (2) and cylinder lock case (1)



    Click image to see an enlarged view

    Fig. Ignition switch assembly (1) and mounting screws (2)

  6.  
  7. Disconnect the connector located by the ignition switch.
  8.  
  9. Remove the 2 tapping screws (2) from the ignition switch assembly (1).
  10.  
  11. Remove the ignition switch (1) from the ignition lock cylinder case.
  12.  

To install:

  1. Install the ignition switch (1) and secure by using the 2 tapping screws (2) and tighten to 62 inch lbs. (7 Nm).

    Click image to see an enlarged view

    Fig. Ignition switch assembly (1) and mounting screws (2)

  2.  
  3. Connect the connector to the ignition switch.
  4.  
  5. Install the theft deterrent control module (2) onto the ignition lock cylinder case (1).

    Click image to see an enlarged view

    Fig. Deterrent module (2) and cylinder lock case (1)

  6.  
  7. Install the upper and lower trim covers.
  8.  
  9. Enable the SIR system. Refer to SIR Disabling and Enabling Zone 3 in SIR.
  10.  

 
label.common.footer.alt.autozoneLogo