SRX 2006-2007

Mirrors

Print

Power Mirrors



Diagnosis & Testing


Click image to see an enlarged view

Fig. C2 terminal identification

  1. With the ignition ON , verify with a scan tool the mirror direction switch parameter changes as the switch is activated. The scan tool should change between UP, DOWN, LEFT, RIGHT. If the function does not perform as specified, replace the driver door module.
  2.  
  3. Verify with a scan tool the mirror select switch parameter changes as the switch is activated. The scan tool should change between RIGHT and LEFT. If the function does not perform as specified, replace the driver door module.
  4.  
  5. With the ignition OFF , unplug the appropriate outside rearview mirror C2 harness connector.
  6.  
  7. With the ignition OFF , test for less than 1 ohm of resistance at each mirror motor control circuit (terminals 1 and 2) between the outside rearview mirror C2 harness connectors and ground. If greater than the specified range, test the appropriate mirror motor control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the appropriate door control module.
  8.  
  9. Connect a test lamp between mirror motor UP control circuit terminal 1 and mirror motor DOWN control circuit terminal 2.
  10.  
  11. Command the appropriate mirror to the UP and DOWN positions with a scan tool. The test lamp should turn on when commanding the UP and DOWN states. If the test lamp remains off during either of the commands, test for a short to ground on either control circuit. If the circuit tests normal, replace the appropriate door control module.
  12.  
  13. Connect a test lamp between mirror motor LEFT control circuit terminal 3 and mirror motor RIGHT control circuit terminal 2.
  14.  
  15. Command the appropriate mirror to the LEFT and RIGHT positions with a scan tool. The test lamp should turn ON when commanding the LEFT and RIGHT states. If the test lamp remains OFF during either of the commands, test for a short to ground on either control circuit. If the circuit tests normal, replace the appropriate door control module.
  16.  
  17. If all circuits test normal, test or replace the appropriate outside rearview mirror.
  18.  

Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove the door trim panel. Refer to the power locks procedure.
  4.  
  5. Unplug the power mirror wire harness electrical connector.
  6.  
  7. Remove the mirror fasteners.
  8.  
  9. Remove the mirror from the door.
  10.  
  11. Pull the wiring harness through the hole in the mirror patch.
  12.  

To install:

  1. Route the mirror wiring harness through the hole in the mirror patch.
  2.  
  3. Seat the grommet into the hole in the door frame.
  4.  
  5. Install the mirror into the door frame.
  6.  
  7. Install the mirror fasteners in the following sequence. Tighten to 80 inch lbs. (9 Nm):
    1. Tighten the top mirror fastener.
    2.  
    3. Tighten the forward mirror fastener.
    4.  
    5. Tighten the rear, lower mirror fastener.
    6.  

  8.  
  9. Engage the power mirror electrical connector.
  10.  
  11. Install the door trim panel.
  12.  

Switch
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Insert a flat bladed tool under the front edge of the front door switch.
  4.  
  5. Push the tool firmly towards the switch to disengage the retainer.
  6.  
  7. Lift up on the rear of the switch plate to remove it from the door trim panel.
  8.  
  9. Unplug electrical connectors.
  10.  
  11. Remove the appropriate switch from the bezel by disengaging the side snap walls with a small flat bladed tool.
  12.  
  13. Installation is the reverse of removal.

    Click image to see an enlarged view

    Fig. Disengage the door switch assembly from the panel



    Click image to see an enlarged view

    Fig. Removing the switch from the bezel

  14.  

 
label.common.footer.alt.autozoneLogo