Santa Fe, Vera Cruz 2006-2008

2.7L V6 VIN D Std 5

Print

Trouble Code: C1334



Sensor 3 Fault

Possible Causes:



Damage to Sensor 3
 
Faulty Sensor 3
 

Trouble Code: C1335



Sensor 4 Fault

Possible Causes:



Damage to Sensor 4
 
Faulty Sensor 4
 

Trouble Code: C1513



Brake Switch Error

Possible Causes:



Open circuit in brake switch
 
line
 
Faulty brake light switch
 
Faulty HECU
 

Trouble Code: C1604



HECU Hardware

Possible Causes:



Malfunction of wiring harness or connector.
 
Malfunction of HECU.
 

Trouble Code: C1605



CAN Hardware error

Possible Causes:



Faulty HECU
 

Trouble Code: C1611



CAN Time-out ECM

Possible Causes:



Faulty EMS
 
Faulty HECU
 

Trouble Code: C1612



CAN Time-out TCM

Possible Causes:



Faulty TCU
 
Faulty HECU
 

Trouble Code: C1616



CAN Bus off

Possible Causes:



Open or short circuit in CAN line
 

Trouble Code: C1623



CAN Time-out Steering Angle Sensor

Possible Causes:



Faulty SAS
 
Faulty HECU
 
Open circuit in SAS line
 

Trouble Code: C1625



CAN Time-out ABS/ESP

Possible Causes:



Faulty HECU
 

Trouble Code: C1626



Implausible Control

Possible Causes:



Faulty HECU
 

Trouble Code: C1643



CAN Time-out Yaw Rate & Lateral G Sensor

Possible Causes:



Faulty Yaw Rate & Lateral G Sensor
 
Faulty HECU
 

Trouble Code: C1660



TPMS receiver RF circuit

Possible Causes:



Low Line - all sensors in storage state and no other RF transmissions received
 
Low Line - receiver RF shielding
 
Faulty TPMS Receiver module
 

Trouble Code: C1661



Receiver EEPROM Failure

Possible Causes:



Transient over voltage due to vehicle fault (fault would typically recover)
 
Faulty TPMS Receiver
 

Trouble Code: C1668



Internal Failure Detection

Possible Causes:



Transient over voltage due to vehicle fault (fault would typically recover)
 
Faulty TPMS Receiver
 

Trouble Code: C1702



Variant Coding Error

Possible Causes:



Faulty HECU
 
Replacement of EMS, T/M ECU
 

Trouble Code: C2112



Valve Relay Error

Possible Causes:



Malfunction of wiring harness or connector.
 
Malfunction of HECU.
 
Malfunction of valve relay
 
Poor ground.
 

Trouble Code: C2308



Front-LH Valve error (Inlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2312



Front-LH Valve error (Outlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2316



Front-RH Valve error (Inlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2320



Front-RH Valve error (Outlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2324



Rear-LH Valve error (Inlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2328



Rear-LH Valve error (Outlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2332



Rear-RH Valve error (Inlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2336



Rear-RH Valve error (Outlet Valve)

Possible Causes:



Faulty HECU
 

Trouble Code: C2366



TC Valve Primary (USV1) Error

Possible Causes:



Faulty HECU
 

Trouble Code: C2370



TC Valve Secondary (USV2) Error

Possible Causes:



Faulty HECU
 

Trouble Code: C2372



Electronic Shuttle Valve Primary (HSV1) Error

Possible Causes:



Faulty HECU
 

Trouble Code: C2374



Electronic Shuttle Valve Secondary (HSV2) Error

Possible Causes:



Faulty HECU
 

Trouble Code: C2402



Motor Pump Error

Possible Causes:



Malfunction of wiring harness or connector.
 
Malfunction of HECU.
 
Poor ground.
 

Trouble Code: C2510



Tread Lamp Short Circuit to 12V

Possible Causes:



Short to battery / ground between TREAD lamp and TPMS receiver
 
Open between TREAD lamp and TPMS receiver
 

Trouble Code: C2511



Diagnostic (TPMS) Lamp Short Circuit to 12V

Possible Causes:



Short to battery / ground between TPMS lamp and TPMS receiver
 
Open between TPMS lamp and TPMS receiver
 

Trouble Code: P0011



'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

Possible Causes:



Oil level and condition
 
OCV
 
CVVT
 

Trouble Code: P0012



'A' Camshaft Position - Timing Over-Retarded (Bank 1)

Possible Causes:



Oil level and condition
 
OCV
 
CVVT
 

Trouble Code: P0016



Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

Possible Causes:



Oil level and condition
 
OCV
 
CVVT
 
Timing mark alignment
 

Trouble Code: P0018



Crankshaft Position- Camshaft Position Correlation (Bank 2 Sensor A)

Possible Causes:



Poor connection
 
Contamination of Oil / Clog of Oil path
 
CKPS, CMPS
 
OCV
 
CVVT
 

Trouble Code: P0021



-A- Camshaft Position- Timing Over-Advanced or System Performance (Bank 2)

Possible Causes:



Poor connection
 
Contamination of Oil / Clog of Oil path
 
OCV
 
CVVT
 

Trouble Code: P0022



-A- Camshaft Position- Timing Over Retarded (Bank 2)

Possible Causes:



Engine oil
 
OCV
 
CVVT stuck
 
Faulty PCM
 

Trouble Code: P0026



Intake Valve Control Solenoid Circuit Range/Performance (Bank 1)

Possible Causes:



Oil pressure loss
 
OCV seizure
 
Faulty PCM
 

Trouble Code: P0028



Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)

Possible Causes:



Oil pressure loss
 
OCV seizure
 

 
label.common.footer.alt.autozoneLogo