Sentra 2007

Drain & Refill

Print

Specific to:

Nissan Sentra 2007-2012

Draining Engine Coolant

  1. Remove the engine undercover. Refer to Engine Undercover in the Engine Mechanical Section.
  2.  
  3. Open the radiator drain plug at the bottom of the radiator, and remove the radiator filler cap. This is the only step required when partially draining the cooling system (radiator only).
    WARNING
    Perform this step when engine is cold.


    WARNING
    Do not spill engine coolant on drive belt.



    Click image to see an enlarged view

    Fig. Open the radiator drain plug (1) at the bottom of the radiator, and remove the radiator filler cap (Arrow=vehicle front)

  4.  
  5. Follow this step for heater core removal/replacement only. Disconnect the upper heater hose at the engine side and apply moderate air pressure 15 psi maximum air pressure into the hose for 30 seconds to blow the excess coolant out of the heater core.
  6.  
  7. When draining all of the coolant in the system, remove the reservoir tank and drain the coolant, then clean the reservoir tank before installation.
    WARNING
    Do not allow the coolant to contact drive belt.

  8.  
  9. When draining all of the coolant in the system for engine removal or repair, open the drain plug on the cylinder block.

    Click image to see an enlarged view

    Fig. When draining all of the coolant in the system for engine removal or repair, open the drain plug on the cylinder block

  10.  
  11. Check the drained engine coolant for contaminants such as rust, corrosion or discoloration. Flush the engine cooling system if the coolant is contaminated. Follow the "FLUSHING COOLING SYSTEM" procedure.
  12.  

Refilling Engine Coolant

  1. Install the radiator drain plug. Install the reservoir tank and cylinder block drain plug as necessary.
    1. The radiator must be completely empty of coolant and water.
    2.  
    3. Apply sealant to the threads of the cylinder block drain plugs. Use Genuine High Performance Thread Sealant or equivalent.
    4.  

  2.  
  3. If disconnected, reattach the upper radiator hose at the engine side.
  4.  
  5. Set the vehicle heater controls to the full HOT and heater ON position. Turn the vehicle ignition ON with the engine OFF as necessary to activate the heater mode.
  6.  
  7. Install the Tool by installing the radiator cap adapter onto the radiator neck opening. Then attach the gauge body assembly with the refill tube and the venturi assembly to the radiator cap adapter.

    Click image to see an enlarged view

    Fig. Install the Tool [KV991J0070 (J-45695)] by installing the radiator cap adapter onto the radiator neck opening. Then attach the gauge body assembly with the refill tube and the venturi assembly to the radiator cap adapter.

  8.  
  9. Insert the refill hose into the coolant mixture container that is placed at floor level. Make sure the ball valve is in the closed position.
    1. Use the recommended coolant or equivalent. Pre-diluted Genuine NISSAN Long Life Anti-Freeze/Coolant (blue) concentrate is recommended by manufacturer. If an equivalent coolant other than Pre-diluted Genuine NISSAN Long Life Anti-Freeze/Coolant (blue) is used, follow the coolant manufacturer-s instructions to maintain minimum freeze protection to 34°F (-37°C). The use of other types of coolant solutions other than Pre-diluted Genuine NISSAN Long Life Anti-Freeze/Coolant (blue) or equivalent may damage the engine cooling system.
    2.  

  10.  
  11. Install an air hose to the venturi assembly, the air pressure must be within specification. Compressed air supply pressure of 80-119 psi.
    NOTE
    The compressed air supply must be equipped with an air dryer.

  12.  
  13. The vacuum gauge will begin to rise and there will be an audible hissing noise. During this process open the ball valve on the refill hose slightly. Coolant will be visible rising in the refill hose. Once the refill hose is full of coolant, close the ball valve. This will purge any air trapped in the refill hose.
  14.  
  15. Continue to draw the vacuum until the gauge reaches 28 inches of vacuum. The gauge may not reach 28 inches in high altitude locations, use the vacuum specifications based on the altitude above sea level.

    Click image to see an enlarged view

    Fig. Continue to draw the vacuum until the gauge reaches 28 inches of vacuum. The gauge may not reach 28 inches in high altitude locations, use the vacuum specifications below based on the altitude above sea level.



    Click image to see an enlarged view

    Fig. Vacuum specifications

  16.  
  17. When the vacuum gauge has reached the specified amount, disconnect the air hose and wait 20 seconds to see if the system loses any vacuum. If the vacuum level drops, perform any necessary repairs to the system and repeat steps 6 - 8 to bring the vacuum to the specified amount. Recheck for any leaks.
  18.  
  19. Place the coolant container (with the refill hose inserted) at the same level as the top of the radiator. Then open the ball valve on the refill hose so the coolant will be drawn up to fill the cooling system. The cooling system is full when the vacuum gauge reads zero.
    NOTE
    Do not allow the coolant container to get too low when filling, to avoid air from being drawn into the cooling system.

  20.  
  21. Remove the Tool from the radiator neck opening.
  22.  
  23. Fill the cooling system reservoir tank to the specified level and install the radiator cap. Run the engine to warm up the cooling system and top up the system as necessary.
  24.  
  25. Install the engine undercover. Refer to Engine Undercover in the Engine Mechanical Section.
  26.  

Flushing Cooling System

  1. Fill radiator and reservoir tank with water and install radiator cap.
  2.  
  3. Run engine until it reaches normal operating temperature.
  4.  
  5. Rev the engine two or three times under no-load.
  6.  
  7. Stop the engine and wait until it cools down.
  8.  
  9. Drain water from the cooling system.
  10.  
  11. Repeat steps 1 through 5 until clear water begins to drain from the radiator.
  12.  

 
label.common.footer.alt.autozoneLogo