Sentra 2008

Window Systems

Print

Power Windows



Initialization/Relearn

If any of the following work has been done, initialize the system.



Electric power supply to power window switch or motor is interrupted by blown fuse or disconnecting battery cable, etc.
 
Removal and installation of the regulator assembly.
 
Removal and installation of the motor from the regulator assembly.
 
Removal and installation of the harness connector of the power window switch.
 
Window is partly opened and/or closed many times without being fully closed.
 
Removal and installation of the door glass.
 
Removal and installation of the door glass run.
 

Initialization

  1. After installing each component to the vehicle, follow the steps below.
    1. Close all doors.
    2.  
    3. Turn ignition switch ON.
    4.  
    5. Open the window to its full down position by operating the power window switch.
    6.  
    7. Move the power window switch in the up direction (auto close position) and hold. Keep holding the switch even when window is completely closed, for at least 4 seconds.
    8.  
    9. Confirm the window is now operating correctly.
    10.  

  2.  

Removal & Installation
Front Door Glass

Specific to:

Nissan Sentra 2007-2012

  1. Remove the front door finisher. Refer to Door Finisher in the Body Section.
  2.  
  3. Disconnect the front door speaker electrical connector.
  4.  
  5. Position aside the vapor barrier.
  6.  
  7. If equipped, reconnect the power window switch electrical connector. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.

    Click image to see an enlarged view

    Fig. If equipped, reconnect the power window switch electrical connector. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.

  8.  
  9. Remove the door glass bolts.
  10.  
  11. While holding the door window, raise it at the rear end to pull the glass out of the sash toward the inside of the door.

    Click image to see an enlarged view

    Fig. While holding the door window, raise it at the rear end to pull the glass out of the sash toward the inside of the door.

  12.  
  13. Remove the door glass run from the door panel.
  14.  

To install:

  1. Install the door glass run to the door panel.
  2.  
  3. While holding the door window, raise it at the rear end to push the glass into the sash away from the inside of the door.
  4.  
  5. Install the door glass bolts.
  6.  
  7. If equipped, reconnect the power window switch electrical connector. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.
  8.  
  9. Reposition the vapor barrier.
  10.  
  11. Connect the front door speaker electrical connector.
  12.  
  13. Install the front door finisher. Refer to Door Finisher in the Body Section.
  14.  

Rear Door Glass

Specific to:

Nissan Sentra 2007-2012

  1. Remove the rear door finisher. Refer to Door Finisher in the Body Section.
  2.  
  3. Position aside the vapor barrier.
  4.  
  5. Remove partition sash bolt and screw, pull the partition sash downward and tilt the upper end of the sash forward to pull the sash out upward.

    Click image to see an enlarged view

    Fig. Remove partition sash bolt and screw, pull the partition sash downward and tilt the upper end of the sash forward to pull the sash out upward

  6.  
  7. Pull out the partition glass in the direction.

    Click image to see an enlarged view

    Fig. Pull out the partition glass in the direction as shown

  8.  
  9. If equipped, reconnect the power window switch electrical connector. Operate the power window switch to raise/lower the door window until the glass bolts can be seen.
  10.  
  11. Remove the rear door glass bolts.
  12.  
  13. Pull out the rear door glass toward the outside of the door to remove.

    Click image to see an enlarged view

    Fig. Remove the rear door glass bolts. Pull out the rear door glass toward the outside of the door to remove.

  14.  
  15. Remove the door glass run from the door panel.
  16.  

To install:

  1. Install the door glass run to the door panel.
  2.  
  3. Push the rear door glass toward the inside of the door to install.
  4.  
  5. Install the rear door glass bolts.
  6.  
  7. If equipped, reconnect the power window switch electrical connector. Operate the power window switch to raise/lower the door window until the glass bolts can be seen.
  8.  
  9. Push in the partition glass.
  10.  
  11. Install partition sash bolt and screw, pull the partition sash upward and tilt the upper end of the sash backward to push the sash in downward.
  12.  
  13. Reposition the vapor barrier.
  14.  
  15. Install the rear door finisher. Refer to Door Finisher in the Body Section.
  16.  

Front Regulator

Specific to:

Nissan Sentra 2007-2012

  1. Remove the front door finisher. Refer to Door Finisher in the Body Section.
  2.  
  3. Disconnect the front door speaker electrical connector.
  4.  
  5. Position aside the vapor barrier.
  6.  
  7. If equipped, reconnect the power window switch connector. Operate the power window main switch to raise/lower the door window until the door glass bolts can be seen.

    Click image to see an enlarged view

    Fig. If equipped, reconnect the power window switch electrical connector. Operate the power window main switch to raise/lower the door window until the glass bolts can be seen.

  8.  
  9. Remove the door glass bolts.
  10.  
  11. Raise the door glass and hold with a suction lifter.

    Click image to see an enlarged view

    Fig. Raise the door glass and hold with a suction lifter (A).

  12.  
  13. If equipped, disconnect the power window switch connector from the regulator assembly.
  14.  
  15. Remove the regulator bolts and regulator assembly.
    1. If equipped remove bolt.

      Click image to see an enlarged view

      Fig. Remove the regulator bolts and regulator assembly. If equipped remove bolt (A).

    2.  

  16.  

To install:

  1. Install the regulator bolts and regulator assembly.
  2.  
  3. If equipped, connect the power window switch connector to the regulator assembly.
  4.  
  5. Raise the door glass and hold with a suction lifter.
  6.  
  7. Install the door glass bolts.
  8.  
  9. If equipped, connect the power window switch connector. Operate the power window main switch to raise/lower the door window until the door glass bolts can be seen.
  10.  
  11. Reposition the vapor barrier.
  12.  
  13. Connect the front door speaker electrical connector.
  14.  
  15. Install the front door finisher. Refer to Door Finisher in the Body Section.
  16.  

Rear Regulator

Specific to:

Nissan Sentra 2007-2012

  1. Remove and position aside the rear door finisher. Refer to Door Finisher in the Body Section.
  2.  
  3. Position aside the vapor barrier.
  4.  
  5. If equipped, reconnect the power window switch electrical connector. Operate the power window switch to raise/lower the door window until the glass bolts can be seen.
  6.  
  7. Remove the rear door glass bolts.

    Click image to see an enlarged view

    Fig. Remove the rear door glass bolts. Pull out the rear door glass toward the outside of the door to remove.

  8.  
  9. Raise up the door glass and hold with a suction lifter.

    Click image to see an enlarged view

    Fig. Raise up the door glass and hold with a suction lifter (A).

  10.  
  11. Remove the regulator bolts, and then remove the regulator assembly from the door panel.

    Click image to see an enlarged view

    Fig. Remove the regulator bolts, and then remove the regulator assembly from the door panel

  12.  

To install:

  1. Install the regulator bolts, and then install the regulator assembly to the door panel.
  2.  
  3. Raise up the door glass and hold with a suction lifter.
  4.  
  5. Install the rear door glass bolts.
  6.  
  7. If equipped, reconnect the power window switch electrical connector. Operate the power window switch to raise/lower the door window until the glass bolts can be seen.
  8.  
  9. Reposition the vapor barrier.
  10.  
  11. Install and position the rear door finisher. Refer to Door Finisher in the Body Section.
  12.  

 
label.common.footer.alt.autozoneLogo