Sierra, Silverado 2006-2007

4.3L V6 VIN X Auto 7

Print

Trouble Code: P0851



Park/Neutral Position (PNP) Switch Circuit Low Voltage

Possible Causes:



It is possible for this DTC to set due to a stack-up or misalignment issue between the IMS and the P/N Switch, where no electrical fault is present. Ensure the gear shift selector cable is properly adjusted and there are no service bulletins that address this concern before replacing parts.
 

Trouble Code: P0852



Park/Neutral Position (PNP) Switch Circuit High Voltage

Possible Causes:



It is possible for this DTC to set due to a stack-up or misalignment issue between the IMS and the P/N Switch, where no electrical fault is present. Ensure the gear shift selector cable is properly adjusted and there are no service bulletins that address this concern before replacing parts.
 

Trouble Code: P0856



Traction Control Torque Request Circuit

Possible Causes:

C0298 A requested torque signal malfunction is only one possible cause for the PCM to lose the ability to perform traction control. DTC C0298 may set due to engine overheating, throttle actuator control failure, loss of ignition timing control by the PCM, etc. If DTC P0856 has not set, refer to the following in order to identify other possible causes of DTC C0298:



Symptoms - Engine Controls for the 4.3L engine
 
Symptoms - Engine Controls for the 8.1L engine
 
Symptoms - Engine Controls for the 4.8L, 5.3L, and 6.0L engines
 
Symptoms - Engine Controls for the 6.6L (LBZ and LLY) engine
 



Testing for Electrical Intermittents
 
Testing for Intermittent Conditions and Poor Connections
 
Connector Repairs
 
Wiring Repairs
 

Trouble Code: P0872



Transmission Pressure Switch 3 Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.When DTC P0762 and P0872 are set in combination, this may indicate a short to ground is present at the pressure switch circuit.This DTC may indicate that SS3 is mechanically defective.This DTC can be set by a loss of prime.
 

Trouble Code: P0873



Transmission Pressure Switch 3 Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.When DTC P0761 and DTC P0873 are set in combination, this may indicate an open circuit condition is present in PS3.This DTC may indicate that SS3 is mechanically defective.This DTC can be caused by a loss of prime.
 

Trouble Code: P0877



Transmission Pressure Switch 4 Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC could indicate a hydraulic leak path exhausting pressure from the reverse PS4.
 

Trouble Code: P0878



Transmission Pressure Switch 4 Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC could indicate a hydraulic leak path exhausting pressure from the reverse PS4.
 

Trouble Code: P0880



Transmission Control Module (TCM) Power Input Signal

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0881



Transmission Control Module (TCM) Power Input Signal Performance

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.Vehicle accessories imposing a large load on the battery circuit could also cause this DTC to set.Loose or corroded battery cables could allow this DTC to set.An internal TCM failure, due to a burn up circuit trace, could allow this DTC to set.Vehicle charging system failure may cause this DTC to set under certain circumstances.A defective vehicle battery may induce this DTC.Running the engine with a battery charger attached may cause this DTC to set.
 

Trouble Code: P0882



Transmission Control Module (TCM) Power Input Signal Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.A defective vehicle battery may allow this DTC to set. Test the vehicle battery to verify proper voltage and load capacity.A defective vehicle charging system may cause this DTC to set.
 

Trouble Code: P0883



Transmission Control Module (TCM) Power Input Signal High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC is normally set due to vehicle charging system concerns.
 

Trouble Code: P0894



Transmission Component Slipping

Possible Causes:



Bronze material found in the transmission oil pan may indicate stator shaft bushing wear. If bushing wear is suspected, inspect the stator shaft and the input, turbine, shaft for damage.
 
Refer to Symptoms - Automatic Transmission for more information.
 

Trouble Code: P0960



Pressure Control Solenoid (PCS) Main Modulation (MAIN MOD) Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0960, set in combination with DTC P2727 and P2761, may indicate an open in the high side driver circuit.
 

Trouble Code: P0961



Line Pressure Control (PC) Solenoid System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0962



Pressure Control Solenoid (PCS) Main Modulation (MAIN MOD) Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0963



Pressure Control Solenoid (PCS) Main Modulation (MAIN MOD) Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0964



Pressure Control Solenoid 2 (PCS2) Control Circuit Open (B)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0964 set in combination with DTC P0972, P0975 and P0978 may indicate an open in the HSD2 circuit.
 

Trouble Code: P0965



Clutch Pressure Control (PC) Solenoid 2 System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, it may be helpful to ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0966



Pressure Control Solenoid 2 (PCS2) Control Circuit Low (B)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0967



Pressure Control Solenoid 2 (PCS2) Control Circuit High (B)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0969



Clutch Pressure Control (PC) Solenoid 3 System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0970



Clutch Pressure Control (PC) Solenoid 3 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0971



Clutch Pressure Control (PC) Solenoid 3 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0972



Shift Solenoid 1 (SS1) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0972, when set in combination with DTC P0964, P0975 and P0978, may indicate an open in the actuator supply voltage 2 circuit.
 

Trouble Code: P0973



Shift Solenoid 1 (SS1) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0974



Shift Solenoid 1 (SS1) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0975



Shift Solenoid 2 (SS2) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0975, when set in combination with DTC P0964, P0972 and P0978, may indicate an open in the actuator supply voltage 2 circuit
 

Trouble Code: P0976



Shift Solenoid 2 (SS2) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0977



Shift Solenoid 2 (SS2) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0978



Shift Solenoid 3 (SS3) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0978, when set in combination with DTC P0964, P0972 and P0975, may indicate an open in the actuator supply voltage 2 circuit.
 

Trouble Code: P0979



Shift Solenoid 3 (SS3) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0980



Shift Solenoid 3 (SS3) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0989



Transmission Fluid Pressure (TFP) Switch 5 Circuit Low Voltage

Trouble Code: P0990



Transmission Fluid Pressure (TFP) Switch 5 Circuit High Voltage

Trouble Code: P0A01



Starter/Generator Control Module Coolant Temperature Sensor 1 Performance

Trouble Code: P0A02



Starter/Generator Control Module Coolant Temperature Sensor 1 Circuit Low Voltage

Trouble Code: P0A03



Starter/Generator Control Module Coolant Temperature Sensor 1 Circuit High Voltage

Trouble Code: P0A06



Battery Energy Control Module Read Only Memory (ROM)

Possible Causes:



If condition is not present, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0A07



Battery Energy Control Module 5-Volt Reference Circuit

Possible Causes:



If condition is not present, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0A0A



High Voltage System Interlock Circuit

Possible Causes:



Ensure that all connectors are connected properly.
 

 
label.common.footer.alt.autozoneLogo