Sierra, Silverado 2006-2007

6.6L V8 VIN 2 Auto 4

Print

Trouble Code: P0699



5-Volt Reference 3 Circuit High Voltage

Trouble Code: P0700



Transmission Control Module (TCM) Requested MIL Illumination

Trouble Code: P0701



Transmission Control System Performance

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0701 may be logged if a forward or REVERSE range is selected immediately after the engine is started, and before the TCM detects pressure at the switches, 2-6 seconds after the engine starts.A plugged control main filter may cause DTC P0701 to set.
 

Trouble Code: P0703



Brake Switch Circuit

Possible Causes:

DTC P0703 indicates that the TCM did not see the proper input signal for service brake status during an acceleration or deceleration cycle. This may indicate an open or short in the TCC brake switch/cruise control release circuit or a faulty stop lamp switch.



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0706



Transmission Range (TR) Switch Performance

Trouble Code: P0708



Transmission Range (TR) Sensor Circuit High

Possible Causes:

Important: Due to the TCM logic used to detect and set DTC P0708, this code can remain active even after an IMS switch replacement is complete and the ignition has been cycled. Therefore, always clear all active DTCs from the TCM after servicing the IMS switch.



Inspect the wiring for poor electrical connections at the TCM and powertrain control module (PCM). Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.Due to this failure and associated response, DTC P0722 can also set.When monitoring "TR SW" while moving the selector through ranges, A/B/C/P states may indicate transitional states. Transitional states are the area between ranges.TR SW A/B/C/P may indicate invalid states when selecting ranges. Invalid states confirm a concern is present.
 

Trouble Code: P0711



Transmission Fluid Temperature (TFT) Sensor Performance

Trouble Code: P0712



Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage

Possible Causes:



The scan tool displays the transmission fluid temperature in degrees. After the transmission is operating, the fluid temperature should rise steadily to a normal operating temperature, then stabilize.
 
Verify the customer's driving habits, trailer towing, etc. Trailer towing should occur in D3.
 

Trouble Code: P0713



Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Trouble Code: P0716



Input Speed Sensor Performance

Possible Causes:



DTC P0716 defaults to an elevated line pressure condition which may result in partial torque converter clutch (TCC) apply. This may produce an idle surge that could stall the engine.
 

Trouble Code: P0717



Input Speed Sensor Circuit Low Voltage

Possible Causes:



DTC P0717 defaults to an elevated line pressure condition which may result in partial torque converter clutch (TCC) apply. This may produce an idle surge that could stall the engine.
 

Trouble Code: P0719



Brake Switch Circuit Low Voltage

Possible Causes:



Inspect the brake switch for proper mounting and operation.
 
Inspect for ABS DTCs. A faulty ABS condition may contribute to setting DTC P0719.
 

Trouble Code: P0721



Output Speed Sensor Circuit Performance

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.If the condition is intermittent, connect the scan tool and select the speed sensor indicated by the code. If the signal is erratic, investigate and eliminate the following:

Intermittent wiring connection
 
Excessive vibration, such as driveline or engine torsionals
 
Irregular sensor gap, such as a loose sensor, a loose tone wheel or a damaged tone wheel
 
Inspect that the speed sensor wiring consists of twisted pairs at the rate of 12-16 twists per 300 mm (12 in). These twists must extend the entire length of the wiring harness to within at least 50 mm (2 in) of the speed sensor connector.
 

 

Trouble Code: P0722



Output Speed Sensor Circuit No Signal

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.If the condition is intermittent, connect the scan tool and select the speed sensor indicated by the code. If the signal is erratic, investigate and eliminate the following:

Intermittent wiring connection
 
Excessive vibration, such as driveline or engine torsionals
 
Irregular sensor gap, such as a loose sensor, a loose tone wheel or a damaged tone wheel
 
Inspect that the speed sensor wiring consists of twisted pairs at the rate of 12-16 twists per 300 mm (12 in). These twists must extend the entire length of the wiring harness to within at least 50 mm (2 in) of the speed sensor connector.
 

 

Trouble Code: P0724



Brake Switch Circuit High Voltage

Possible Causes:



Inspect the brake switch for proper mounting and operation.
 
Inspect for ABS DTCs. A faulty ABS condition may contribute to setting DTC P0724.
 

Trouble Code: P0726



Engine Speed Sensor Circuit Performance

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.If the condition is intermittent, connect the scan tool and select the speed sensor indicated by the code. If the signal is erratic, investigate and eliminate the following:

Intermittent wiring connection
 
Excessive vibration, such as driveline or engine torsionals
 
Irregular sensor gap, such as a loose sensor, a loose tone wheel or a damaged tone wheel
 
Inspect that the speed sensor wiring consists of twisted pairs at the rate of 12-16 twists per 300 mm (12 in). These twists must extend the entire length of the wiring harness to within at least 50 mm (2 in) of the speed sensor connector.
 

 

Trouble Code: P0727



Engine Speed Sensor Circuit No Signal

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.If the condition is intermittent, connect the scan tool and select the speed sensor indicated by the code. If the signal is erratic, investigate and eliminate the following:

Intermittent wiring connection
 
Excessive vibration, such as driveline or engine torsionals
 
Irregular sensor gap, such as a loose sensor, a loose tone wheel or a damaged tone wheel
 
Inspect that the speed sensor wiring consists of twisted pairs at the rate of 12-16 twists per 300 mm (12 in). These twists must extend the entire length of the wiring harness to within at least 50 mm (2 in) of the speed sensor connector.
 

 

Trouble Code: P0729



Incorrect 6th Gear Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 2-6 clutch and 3-5-6-REVERSE clutch for 6th range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for the specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0730



Incorrect Gear Ratio

Possible Causes:



A false or incorrect AT OSS or AT ISS signal can set DTC P0730.
 
DTC P0894 detects an incorrect gear ratio in fourth gear with the torque converter clutch (TCC) applied.
 
Inspect for any improperly installed aftermarket equipment.
 
Sticking or contamination of shift valves may cause intermittent incorrect gear ratios.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 
DTC P0730 defaults to an elevated line pressure which may result in partial TCC apply. This may produce an idle surge that could stall the engine.
 

Trouble Code: P0731



Incorrect 1st Gear Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 1-2-3-4 clutch or low and reverse clutch for 1st range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for the specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0732



Incorrect 2nd Gear Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 1-2-3-4 clutch and 2-6 clutch for 2nd range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0733



Incorrect 3rd Gear Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 1-2-3-4 clutch and 3-5-Reverse clutch, for 3rd range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0734



Incorrect 4th Gear Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 1-2-3-4 clutch and 4-5-6 clutch, for 4th range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0735



Incorrect 5th Gear Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 4-5-6 clutch and 3-5-Reverse clutch, for 5th range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0736



Incorrect Reverse Ratio

Possible Causes:



Incorrect ratio codes typically indicate mechanical conditions with specific clutches, such as 3-5-Reverse clutch and low and reverse clutch for REVERSE range.
 
Incorrect ratio code could indicate a hydraulically failed solenoid. Observe DTC information for specific solenoid.
 
Clutch test mode can be used to measure stall speed. Observe turbine speed signal. If the turbine speed signal does not return to zero or rises during the stall test, a leak or obstruction in a specific clutch apply circuit could be present.
 
You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0740



Torque Converter Clutch (TCC) Enable Solenoid Control Circuit

Possible Causes:



With the TCC engaged, the TCC slip speed should be -20 to +50 RPM.
 

Trouble Code: P0741



Torque Converter Clutch (TCC) System - Stuck Off

Possible Causes:



Contamination may cause the TCC apply valve to stick in the valve body.
 
There may be internal damage in the torque converter causing the no TCC apply.
 

Trouble Code: P0742



Torque Converter Clutch (TCC) System - Stuck On

Possible Causes:

The TCC fluid hydraulically applies the TCC, possibly causing an engine stall, under the following conditions:



The TCC is hydraulically stuck ON
 
The parking brake is applied
 
Any gear range is selected
 

Trouble Code: P0748



Pressure Control (PC) Solenoid Control Circuit

Possible Causes:



DTC P0748 may set under low voltage conditions caused by high electrical system demands.
 

Trouble Code: P0751



1-2 Shift Solenoid Valve Performance - No First or Fourth Gear

Possible Causes:



Verify that the transmission meets the specifications in the Shift Speed .
 
Other internal transmission failures may cause more than one shift to occur.
 
Refer to the Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0752



1-2 Shift Solenoid Valve Performance - No Second or Third Gear

Possible Causes:



Verify that the transmission meets the specifications in the Shift Speed .
 
Other internal transmission failures may cause more than one shift to occur.
 
Refer to the Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0753



1-2 Shift Solenoid Control Circuit

Possible Causes:



Refer to the Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0756



2-3 Shift Solenoid Valve Performance - No First or Second Gear

Possible Causes:



Verify that the transmission meets the specifications in the Shift Speed .
 
Other internal transmission failures may cause more than one shift to occur.
 
Refer to the Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0757



2-3 Shift Solenoid Valve Performance - No Third or Fourth Gear

Possible Causes:



Verify that the transmission meets the specifications in the Shift Speed .
 
Other internal transmission failures may cause more than one shift to occur. Refer to the Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0758



2-3 Shift Solenoid Control Circuit

Possible Causes:



Refer to the Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0761



Shift Solenoid (SS) 3 Valve Performance - Stuck Off

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC may indicate that SS3 is mechanically defective or the shift valve is stuck in the destroked state.When DTC P0761 and P0873 are set in combination, this may indicate an open circuit condition is present at the pressure switch circuit or the shift valve is stuck in the destroked position.
 

Trouble Code: P0762



Shift Solenoid (SS) 3 Valve Performance - Stuck On

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC may indicate that SS3 is mechanically defective or the shift valve is stuck in the stroked state.When DTC P0762 and P0872 are set in combination, this may indicate a short to ground is present at the pressure switch circuit or the shift valve is stuck in the stroked state.
 

Trouble Code: P0776



Pressure Control Solenoid 2 (PCS2) Stuck Off

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC indicates the on-coming clutch being controlled by PCS2 is not applied or applied too slowly. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, in order to determine the specific shift when the DTC was set. Refer to Solenoid and Clutch Chart to determine which clutch circuit is suspect.Important: Clutch failure due to installation of an engine power upgrade is not covered under the transmission manufacturers warranty. Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur.
 

Trouble Code: P0777



Pressure Control Solenoid 2 (PCS2) Stuck On

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC indicates the off-going clutch, being controlled by PCS2, is not releasing or is slow to release. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, to determine the specific shift when the DTC was set. Refer to the Solenoid and Clutch Chart to determine which clutch circuit is suspect.Important: Clutch failure due to installation of an engine power upgrade is not covered under the transmission manufacturers warranty. Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur.
 

Trouble Code: P0785



3-2 Shift Solenoid (SS) Control Circuit

 
label.common.footer.alt.autozoneLogo