Sierra, Silverado 2006-2007

6.6L V8 VIN 2 Auto 6

Print

Trouble Code: P1630



Theft Deterrent Learn Mode Active

Trouble Code: P1631



Theft Deterrent Fuel Enable Signal Not Correct

Possible Causes:

Important: Do not clear DTCs unless directed by a diagnostic procedure. Clearing DTCs will also clear valuable Freeze Frame and Failure Records data.



If the PCM is replaced, the PCM must re-learn a valid password and crankshaft variation.
 
If the BCM is replaced, the PCM must re-learn a valid password.
 
Check for published service bulletins relating to exhibited symptoms or component operation.
 
If the vehicle does not start, or starts and stalls:

Turn OFF the ignition and wait at least 5 seconds before trying to restart.
 
If a fault or tamper has been detected, the BCM will not forward the correct password to the PCM for a period of 10 minutes, even if the condition is corrected during that time period. This may cause a DTC P1631 to set in the PCM. This timer can be monitored in the Passlock Data parameter of the scan tool. Once the time has elapsed, the BCM will determine if the condition is still present.
 

The PCM and BCM parameters can be monitored with a scan tool.The Passlock state and the auto learn timer can be viewed in the Passlock Data parameter of the scan tool.Inspect the following for preventing the Passlock sensor from communicating with the BCM:

Passlock sensor
 
Ignition switch assembly
 
Passlock sensor circuitry
 
Bent pins at the small Passlock sensor
 

If this DTC sets along with a DTC B2960, then the problem was caused by malfunctioning Passlock components or circuitry, not the PCM.Inspect all related wiring and connections including the PCM and BCM connections. These may cause an intermittent malfunction.An intermittent may be caused by any of the following conditions:

A poor connection
 
Rubbed through wire insulation
 
A broken wire inside the insulation
 

Thoroughly inspect any circuitry that is suspected of causing the intermittent complaint. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.
 

Trouble Code: P1644



Traction Control Delivered Torque Output Circuit

Possible Causes:

Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to the following:



Testing for Electrical Intermittents
 
Testing for Intermittent Conditions and Poor Connections
 
Wiring Repairs
 
Connector Repairs
 

Trouble Code: P1688



Unmanaged Engine Torque Delivered to Transmission Control Module (TCM) Signal

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P1689



Traction Control Delivered Torque Output Circuit

Possible Causes:

Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to the following:



Testing for Electrical Intermittents
 
Testing for Intermittent Conditions and Poor Connections
 
Wiring Repairs
 
Connector Repairs
 

Trouble Code: P1779



Engine Torque Delivered to Transmission Control Module (TCM) Signal

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P1810



Transmission Fluid Pressure (TFP) Position Switch Circuit

Possible Causes:



Refer to the Transmission Fluid Pressure (TFP) Manual Valve Position Switch Logic table for the normal range signals and the invalid combinations. On the table, LOW is 0 volts, HI is ignition voltage.
 
Sediment in the valve body may cause improper operation of the TFP manual valve position switch. If sediment intrusion is suspected, clean the valve body and replace the TFP manual valve position switch.
 

Trouble Code: P2066



Fuel Level Sensor 2 Performance

Possible Causes:



Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same Freeze Frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate when the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 

Trouble Code: P2067



Fuel Level Sensor 2 Circuit Low Voltage

Possible Causes:



Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate when the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 

Trouble Code: P2068



Fuel Level Sensor 2 Circuit High Voltage

Possible Causes:



Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate when the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 

Trouble Code: P2122



Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

Trouble Code: P2123



Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

Trouble Code: P2127



Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

Trouble Code: P2128



Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

Trouble Code: P2138



Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Trouble Code: P2146



Injector Positive Voltage Control Circuit Group 1

Trouble Code: P2149



Injector Positive Voltage Control Circuit Group 2

Trouble Code: P2152



Injector Positive Voltage Control Circuit Group 3

Trouble Code: P2155



Injector Positive Voltage Control Circuit Group 4

Trouble Code: P2199



Intake Air Temperature (IAT) Sensor 1-2 Correlation

Possible Causes:



1. A slight to moderate resistance in either signal or low reference circuit, can widen the spread between the two IAT sensors, and cause this DTC to set.
 
2. An IAT sensor that is skewed lower at various ambient temperatures, due to more resistance than is normal, can widen the spread between the two sensors and cause this DTC to set. Measure and record the resistance of the IAT sensor 1 and IAT sensor 2 at various ambient temperatures, and then compare those measurements to the Temperature vs. Resistance Table. Refer to Temperature Versus Resistance .
 
3. Inspect IAT sensor 1 and sensor 2 terminals, for corrosion or a poor connection.
 
4. If the ignition has been OFF for more than 10 hours, then determine which IAT sensor is skewed by comparing ECT, IAT sensor 1, and IAT sensor 2 parameters with a scan tool.
 

Trouble Code: P2228



Barometric Pressure (BARO) Sensor Circuit Low Voltage

Trouble Code: P2229



Barometric Pressure (BARO) Sensor Circuit High Voltage

Trouble Code: P2510



Engine Control Module Relay Circuit

Trouble Code: P2544



Transmission Torque Request Circuit

Possible Causes:



This diagnostic trouble code may set due to low system voltage. Ensure that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test . Verify charging system is operating correctly. Refer to Charging System Test . Verify there is no parasitic drain on the battery. Refer to Battery Electrical Drain/Parasitic Load Test .
 

Trouble Code: P2563



Turbocharger Boost Control Position Sensor Performance

Possible Causes:



Verify that any electrical aftermarket devices are properly connected and grounded. Refer to Checking Aftermarket Accessories .
 
A MAP sensor that is skewed or bias may cause this DTC to set.
 
A restricted oil supply feed to the turbocharger may cause this DTC to set. Refer to Turbocharger Lack of Oil Supply .
 

Trouble Code: P2564



Turbocharger Boost Control Position Sensor Circuit Low Voltage

Possible Causes:



Verify that any electrical aftermarket devices are properly connected and grounded. Refer to Checking Aftermarket Accessories .
 

Trouble Code: P2565



Turbocharger Boost Control Position Sensor Circuit High Voltage

Possible Causes:



Verify that any electrical aftermarket devices are properly connected and grounded. Refer to Checking Aftermarket Accessories .
 

Trouble Code: P2610



Control Module Ignition Off Timer Performance

Trouble Code: P2636



Fuel Pump 2 Flow Insufficient

Possible Causes:



When outside temperatures are below 0°C (32°F), the fuel tank pickup screen may ice over from water in the fuel tank.
 
If the engine is running while fueling the vehicle, this DTC may set.
 
The fuel will default to empty when this DTC sets.
 

Trouble Code: P2670



Actuator Supply Voltage 2 Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2671



Actuator Supply Voltage 2 High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P268A



Fuel Injector Calibration Data Not Programmed

Trouble Code: P2723



Pressure Control Solenoid 1 (PCS1) Controlled Clutch Stuck Off

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC indicates the on-coming clutch being controlled by PCS1 is not applied or applied too slowly. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, in order to determine the specific shift when the DTC was set. Refer to the Solenoid and Clutch Chart to determine which clutch circuit is suspect.Important: Clutch failure due to installation of an engine power upgrade is not covered under the manufacturers warranty. Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur.
 

Trouble Code: P2724



Pressure Control Solenoid 1 (PCS1) Controlled Clutch Stuck On

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC indicates the off-going clutch being controlled by PCS1 is not releasing or is slow to release. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, in order to determine the specific shift when the DTC was set. Refer to the Solenoid and Clutch Chart to determine which clutch circuit is suspect.Important: Clutch failure due to installation of an engine power upgrade is not covered under the manufacturers warranty. Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur.
 

Trouble Code: P2727



Pressure Control Solenoid 1 (PCS1) Control Circuit Open (A)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2729



Pressure Control Solenoid 1 (PCS1) Control Circuit Low (A)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2730



Pressure Control Solenoid 1 (PCS1) Control Circuit High (A)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2761



Torque Converter Clutch (TCC) Pressure Control (PC) Solenoid Control Circuit

Trouble Code: P2763



Torque Converter Clutch (TCC) Pressure Control Solenoid (PCS) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2764



Torque Converter Clutch (TCC) Pressure Control Solenoid (PCS) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

 
label.common.footer.alt.autozoneLogo