Sierra, Silverado 2006-2007

6.6L V8 VIN D Auto 2

Print

Trouble Code: P0202



Fuel Injector 2 Control Circuit

Trouble Code: P0203



Fuel Injector 3 Control Circuit

Trouble Code: P0204



Fuel Injector 4 Control Circuit

Trouble Code: P0205



Fuel Injector 5 Control Circuit

Trouble Code: P0206



Fuel Injector 6 Control Circuit

Trouble Code: P0207



Fuel Injector 7 Control Circuit

Trouble Code: P0208



Fuel Injector 8 Control Circuit

Trouble Code: P0218



Transmission Condition Overtemperature

Possible Causes:



The scan tool Trans. Fluid Temp. should rise steadily to a normal operating temperature, then stabilize.
 
Ask about the customer's driving habits, trailer towing, etc. Trailer towing should occur in D3. Refer to Symptoms - Automatic Transmission .
 

Trouble Code: P0218



Transmission Condition Overtemperature

Possible Causes:



The scan tool Trans. Fluid Temp. should rise steadily to a normal operating temperature, then stabilize.
 
Ask about the customer's driving habits, trailer towing, etc. Trailer towing should occur in D3.
 
Refer to Symptoms - Automatic Transmission .
 

Trouble Code: P0230



Fuel Pump Relay Control Circuit

Trouble Code: P0234



Turbocharger Engine Overboost

Trouble Code: P0299



Turbocharger Engine Underboost

Possible Causes:



A MAP sensor that is stuck at BARO, or is 40 kPa lower than desired while under boost, will cause this DTC to set. Use a scan tool and compare the MAP Sensor parameters to a known good vehicle. Operate both vehicles under various conditions.
 

Trouble Code: P0300



Engine Misfire Detected

Trouble Code: P0301



Cylinder 1 Misfire Detected

Trouble Code: P0302



Cylinder 2 Misfire Detected

Trouble Code: P0303



Cylinder 3 Misfire Detected

Trouble Code: P0304



Cylinder 4 Misfire Detected

Trouble Code: P0305



Cylinder 5 Misfire Detected

Trouble Code: P0306



Cylinder 6 Misfire Detected

Trouble Code: P0307



Cylinder 7 Misfire Detected

Trouble Code: P0308



Cylinder 8 Misfire Detected

Trouble Code: P0335



Crankshaft Position (CKP) Sensor Circuit

Possible Causes:



An intermittent CKP sensor signal may cause DTC P0336 to set. Wiggle the wiring harness with the engine running and observe the CKP Sensor Pulses Missed parameter on the scan tool. If the parameter indicates anything other than 0, there is an intermittent condition.
 
Inspect for insufficient fuel.
 

Trouble Code: P0336



Crankshaft Position (CKP) Sensor Performance

Possible Causes:



An intermittent CKP sensor signal may cause DTC P0336 to set. Wiggle the wiring harness with the engine running and observe the CKP Sensor Pulses Missed parameter on the scan tool. If the parameter indicates anything other than 0, there is an intermittent condition.
 
Inspect for insufficient fuel.
 

Trouble Code: P0340



Camshaft Position (CMP) Sensor Circuit

Possible Causes:



An intermittent CMP sensor signal may cause DTC P0340 or P0341 to set. Wiggle the wiring harness with the engine running and observe the Cam Signal Missed parameter of the scan tool. If the parameter indicates anything other than 0, there is an intermittent condition.
 
If the CMP sensor signal is lost while running, the engine will operate normally. If the CMP sensor signal is not present on start-up, the engine will not start.
 

Trouble Code: P0341



Camshaft Position (CMP) Sensor Performance

Possible Causes:



An intermittent CMP sensor signal may cause DTC P0340 or P0341 to set. Wiggle the wiring harness with the engine running and observe the Cam Signal Missed parameter of the scan tool. If the parameter indicates anything other than 0, there is an intermittent condition.
 
If the CMP sensor signal is lost while running, the engine will operate normally. If the CMP sensor signal is not present on start-up, the engine will not start.
 

Trouble Code: P0342



Camshaft Position (CMP) Sensor Circuit Low Voltage

Possible Causes:



An intermittent CMP sensor signal may cause DTC P0340 or P0341 to set. Wiggle the wiring harness with the engine running and observe the Cam Signal Missed parameter of the scan tool. If the parameter indicates anything other than 0, there is an intermittent condition.
 
If the CMP sensor signal is lost while running, the engine will operate normally. If the CMP sensor signal is not present on start-up, the engine will not start.
 

Trouble Code: P0381



Wait To Start Lamp Control Circuit

Possible Causes:



Using the Failure Records data may help locate an intermittent condition. If you cannot duplicate the DTC, the information in the Failure Records can help determine how many miles since the DTC set. The Fail Counter and Pass Counter can help determine how many ignition cycles that the diagnostic test reported a pass and/or a fail. The wait to start indicator illuminates only with the ignition ON and the engine OFF. The wait to start indicator will not illuminate during post-start glow plug operation. The wait to start indicator will not stay ON for long at higher engine temperatures.
 

Trouble Code: P0401



Exhaust Gas Recirculation (EGR) Flow Insufficient

Trouble Code: P0402



Exhaust Gas Recirculation (EGR) Flow Excessive

Trouble Code: P0403



Exhaust Gas Recirculation (EGR) Solenoid Control Circuit

Trouble Code: P0405



Exhaust Gas Recirculation (EGR) Position Sensor Circuit Low Voltage

Trouble Code: P0406



Exhaust Gas Recirculation (EGR) Position Sensor Circuit High Voltage

Trouble Code: P0461



Fuel Level Sensor 1 Performance

Possible Causes:



Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same Freeze Frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 

Trouble Code: P0461



Fuel Level Sensor 1 Performance

Possible Causes:



Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same Freeze Frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0462



Fuel Level Sensor 1 Circuit Low Voltage

Possible Causes:



Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 

Trouble Code: P0462



Fuel Level Sensor 1 Circuit Low Voltage

Possible Causes:



Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0463



Fuel Level Sensor 1 Circuit High Voltage

Possible Causes:



Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
 

Trouble Code: P0463



Fuel Level Sensor 1 Circuit High Voltage

Possible Causes:



Use the Freeze Frame/Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame/Failure Records data may help in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also help in determining the number of ignition cycles that the diagnostic test reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, including those for RPM, for engine load, for vehicle speed, for temperature, and for others. This will isolate at what point the DTC failed. Refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0464



Fuel Level Sensor 1 Circuit Intermittent

Possible Causes:



Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions, i.e. RPM, engine load, vehicle speed, temperature, etc. This will isolate when the DTC failed.
 
Refer to Testing for Intermittent Conditions and Poor Connections .
 
If the DTC sets without a refueling event, refer to Fuel Gage Inaccurate or Inoperative .
 

Trouble Code: P046C



Exhaust Gas Recirculation (EGR) Position Sensor Performance

 
label.common.footer.alt.autozoneLogo