Silverado 2008

Accessory Drive Belts

Print

Accessory Belt Routing



Specific to:

Chevrolet Silverado 1500 2008



Click image to see an enlarged view

Fig. Accessory serpentine belt routing-4.3L engines



Click image to see an enlarged view

Fig. Accessory serpentine belt routing-4.8L, 5.3L & 6.0L engines

Adjustment



Specific to:

Chevrolet Silverado 1500 2008

These vehicles are equipped with a single serpentine belt and spring loaded tensioner. The proper belt adjustment is automatically maintained by the tensioner, therefore, no periodic adjustment is needed. If the pointer is past the scale on the tensioner replace the belt. If correct belt tension cannot be achieved make sure the correct belt is installed. If the correct tension is still not achieved and check for proper mounting off all accessory drives.

Inspection



Specific to:

Chevrolet Silverado 1500 2008

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation



Specific to:

Chevrolet Silverado 1500 2008

Belt replacement is a relatively simple matter rotating the tensioner off the belt (to relieve tension) and holding the tensioner in this position as the belt is slipped from its pulley. The tensioner arm contains a machined receiver for a 3 / 8 in. driver from a ratchet or breaker bar.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Before you begin, visually confirm the belt routing to the engine compartment label (if present) or to the appropriate diagram (if the label is not present). If you cannot make a match (perhaps it is not the original motor for this vehicle), scribble your own diagram before proceeding.
    NOTE
    On the 4.3L engine, remove the air cleaner outlet resonator. On 4.8L, 5.3L and 6.0L engines remove the upper intake sight shield assembly and then the air cleaner assembly.



    Click image to see an enlarged view

    Fig. Air cleaner outlet resonator assembly-4.3L engines



    Click image to see an enlarged view

    Fig. Upper intake manifold sight shield-4.8L, 5.3L & 6.0L engines



    Click image to see an enlarged view

    Fig. Accessory serpentine belt routing-4.3L engines



    Click image to see an enlarged view

    Fig. Accessory serpentine belt routing-4.8L, 5.3L and 6.0L engines

  4.  
  5. Disconnect the negative battery cable.
  6.  
  7. Install the appropriate sized breaker bar, wrench, or socket to the tensioner arm or pulley, as applicable.
  8.  
  9. Rotate the tensioner to the left (counterclockwise) and slip the belt from the tensioner pulley.
  10.  
  11. Once the belt is free from the tensioner, CAREFULLY rotate the tensioner back into position. DO NOT allow the tensioner to suddenly snap into place or damage could occur to the assembly.
  12.  
  13. Slip the belt from the remaining pulleys (this can get difficult is there is little room between the radiator/fan assembly and the accessory pulleys. Work slowly and be patient.
  14.  
  15. Once the belt is free, remove it from the engine compartment.
  16.  

To install:

  1. Route the belt over all the pulleys except the water pump and/or the tensioner. Refer to the routing illustration that you identified as a match before beginning.
  2.  
  3. Rotate the tensioner pulley to the left (counterclockwise) and hold it while you finish slipping the belt into position. Slowly allow the tensioner into contact with the belt.
  4.  
  5. Check to see if the correct V-groove tracking is around each pulley.
    WARNING
    Improper V-groove tracking will cause the belt to fail in a short period of time.

  6.  
  7. Connect the negative battery cable.
  8.  

 
label.common.footer.alt.autozoneLogo