Solstice 2006-2008, Sky 2007-2008

Arming The System

Print

Zone 1



  1. Place the ignition in the OFF position.
  2.  
  3. Connect both connectors to the left and right front end sensors.
  4.  
  5. Connect both CPAs to the left and right front sensor connectors.
  6.  
  7. Install both AIR BAG (IGN) fuse and the AIR BAG (BATT) fuse into the BCM fuse center.
  8.  
  9. Install the kick up panel to cover the BCM fuse center then replace the passenger floor mat.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

Zone 3



  1. Place the ignition in the OFF position.
    NOTE
    This vehicle is equipped with dual stage air bags, you will find 2 connectors. Match the right color connector to the right color opening in the module. Route the steering wheel module wires, the redundant control wires, and the horn wires correctly.

  2.  
  3. Connect both connectors to the steering wheel module.
  4.  
  5. Connect both CPA's to the steering wheel module connectors.
  6.  
  7. Align the steering wheel module fasteners to the steering wheel fastener holes.
  8.  
  9. Push the steering wheel module firmly into the steering wheel in order to engage the fasteners.
  10.  
  11. Install both AIR BAG (IGN) fuse and the AIR BAG (BATT) fuse into the BCM fuse center.
  12.  
  13. Install the kick up panel to cover the BCM fuse center then replace the passenger floor mat.
  14.  
  15. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  16.  

Zone 4



  1. Place the ignition in the OFF position.
    NOTE
    This vehicle is equipped with dual stage air bags. You will find 2 connectors. Match the right color connector to the right color opening in the module. Route the steering wheel module wires, the redundant control wires, and the horn wires correctly.

  2.  
  3. Connect both connectors to the steering wheel module.
  4.  
  5. Connect both CPAs to the steering wheel module connectors.
  6.  
  7. Align the steering wheel module fasteners to the steering wheel fastener holes.
  8.  
  9. Push the steering wheel module firmly into the steering wheel in order to engage the fasteners.
  10.  
  11. Connect the connector to the left seat belt retractor pretensioner.
  12.  
  13. Connect the left CPA connector to the seat belt retractor pretensioner.
  14.  
  15. Connect the connector to the right seat belt retractor pretensioner.
  16.  
  17. Connect the CPA to the right seat belt retractor pretensioner.
  18.  
  19. Install passenger and driver sill plates and front seat back body panel.
  20.  
  21. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  22.  
  23. Connect the CPA to the vehicle harness yellow connector.
  24.  
  25. Close the glove box.
  26.  
  27. Install both AIR BAG (IGN) fuse and the AIR BAG (BATT) fuse into the BCM fuse center.
  28.  
  29. Install the kick up panel to cover the BCM fuse center then replace the passenger floor mat.
  30.  
  31. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  32.  

Zone 5



  1. Place the ignition in the OFF position.
  2.  
  3. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  4.  
  5. Connect the CPA to the vehicle harness yellow connector.
  6.  
  7. Close the glove box.
  8.  
  9. Install both AIR BAG (IGN) fuse and the AIR BAG (BATT) fuse into the BCM fuse center.
  10.  
  11. Install the kick up panel to cover the BCM fuse center then replace the passenger floor mat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 7



  1. Place the ignition in the OFF position.
  2.  
  3. Connect the connector to the left seat belt retractor pretensioner.
  4.  
  5. Connect the CPA to the left seat belt retractor pretensioner.
  6.  
  7. Install driver sill plate and front seat back body panel.
  8.  
  9. Install both AIR BAG (IGN) fuse and the AIR BAG (BATT) fuse into the BCM fuse center.
  10.  
  11. Install the kick up panel to cover the BCM fuse center then replace the passenger floor mat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 9



  1. Place the ignition in the OFF position.
  2.  
  3. Connect the connector to the right seat belt retractor pretensioner.
  4.  
  5. Connect the CPA to the right seat belt retractor pretensioner.
  6.  
  7. Install passenger sill plate and front seat back body panel.
  8.  
  9. Install both AIR BAG (IGN) fuse and the AIR BAG (BATT) fuse into the BCM fuse center.
  10.  
  11. Install the kick up panel to cover the BCM fuse center then replace the passenger floor mat.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

 
label.common.footer.alt.autozoneLogo