Solstice 2006-2008, Sky 2007-2008

Disarming the System

Print

Zone 1



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Place the ignition switch to the OFF position.
  6.  
  7. Remove the passenger floor mat and remove the kick up panel covering the body control module (BCM) fuse center.
    WARNING
    This sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.



    Click image to see an enlarged view

    Fig. BCM fuse center



    Click image to see an enlarged view

    Fig. Front end sensors

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  10.  
  11. Open front hood and locate both the right and left front end sensors.
  12.  
  13. Remove both the right and left connector position assurance (CPA) from the right and left front end sensor connector.
  14.  
  15. Remove both connectors from left and right front end sensors.
  16.  

Zone 3



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Place the ignition switch to the OFF position.
  6.  
  7. Remove the passenger floor mat and remove the kick up panel covering the body control module (BCM) fuse center.
    WARNING
    This sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.

    Click image to see an enlarged view

    Fig. Steering wheel air bag module

  10.  
  11. On the back side of the steering wheel there are 2 openings to access the fasteners securing the steering wheel module.
  12.  
  13. Insert a 3.175 mm ( 1 / 8 inch) diameter blunt ended punch or equivalent tool into each of the holes in order to release the fastener securing the module to the steering wheel.
  14.  
  15. Pull the steering wheel module gently away from the steering wheel.
  16.  
  17. Remove both connector position assurance (CPA) from the steering wheel module connectors.
  18.  
  19. Remove both connectors from the steering wheel module.
  20.  
  21. Remove the steering wheel module.
  22.  

Zone 4



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Place the ignition switch to the OFF position.
  6.  
  7. Remove the passenger floor mat and remove the kick up panel covering the body control module (BCM) fuse center.
    WARNING
    This sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  10.  
  11. Open and lower glove box door fully.
  12.  
  13. Locate the I/P module yellow connector and remove the connector position assurance (CPA) from the vehicle harness yellow connector.
  14.  
  15. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.

    Click image to see an enlarged view

    Fig. Front seat back body panel

  16.  
  17. Remove passenger and driver sill plates and front seat back body panel.
  18.  
  19. Locate the right seat belt retractor pretensioner.
  20.  
  21. Remove the right CPA connector from the seat belt retractor pretensioner.
  22.  
  23. Disconnect the connector from the right seat belt retractor pretensioner.
  24.  
  25. Locate the left seat belt retractor pretensioner.
  26.  
  27. Remove the left CPA connector from the seat belt retractor pretensioner.
  28.  
  29. Disconnect the connector from the left seat belt retractor pretensioner.
  30.  
  31. On the back side of the steering wheel there are 2 openings to access the fasteners securing the steering wheel module.
  32.  
  33. Insert a 3.175 mm ( 1 / 8 inch) diameter blunt ended punch or equivalent tool into each of the holes in order to release the fastener securing the module to the steering wheel.
  34.  
  35. Pull the steering wheel module gently away from the steering wheel.
  36.  
  37. Remove both CPAs from the steering wheel module connectors.
  38.  
  39. Remove both connectors from the steering wheel module.
  40.  
  41. Remove the steering wheel module.
  42.  

Zone 5



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Place the ignition switch to the OFF position.
  6.  
  7. Remove the passenger floor mat and remove the kick up panel covering the body control module (BCM) fuse center.
    WARNING
    This sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  10.  
  11. Open and lower glove box door fully.
  12.  
  13. Locate the I/P module yellow connector and remove the connector position assurance (CPA) from the vehicle harness yellow connector.
  14.  
  15. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  16.  

Zone 7



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Place the ignition switch to the OFF position.
  6.  
  7. Remove the passenger floor mat and remove the kick up panel covering the body control module (BCM) fuse center.
    WARNING
    This sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  10.  
  11. Remove driver sill plate and front seat back body panel.
  12.  
  13. Locate the left seat belt retractor pretensioner.
  14.  
  15. Remove the connector position assurance (CPA) from the left seat belt retractor pretensioner.
  16.  
  17. Disconnect the connector from the left seat belt retractor pretensioner.
  18.  

Zone 9



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Place the ignition switch to the OFF position.
  6.  
  7. Remove the passenger floor mat and remove the kick up panel covering the body control module (BCM) fuse center.
    WARNING
    This sensing and diagnostic module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  10.  
  11. Remove passenger sill plate and front seat back body panel.
  12.  
  13. Locate the right seat belt retractor pretensioner.
  14.  
  15. Remove the connector position assurance (CPA) from the right seat belt retractor pretensioner.
  16.  
  17. Disconnect the connector from the right seat belt retractor pretensioner.
  18.  

 
label.common.footer.alt.autozoneLogo