Solstice 2006-2008, Sky 2007-2008

2.0L L4 VIN X Std 8

Print

Trouble Code: P0662



Engine Controls Ignition Relay Control Circuit

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0685



Engine Controls Ignition Relay Control Circuit

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0686



Engine Controls Ignition Relay Control Circuit Low Voltage

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0687



Engine Controls Ignition Relay Control Circuit High Voltage

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0689



Engine Controls Ignition Relay Feedback Circuit Low Voltage

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P068B



Engine Controls Relay Feedback Circuit High Voltage

Possible Causes:



Powertrain relay shorted to ground on the control circuit
 
Powertrain relay shorted to voltage or an open/high resistance
 
Powertrain relay has failed
 
ECM has failed
 

Trouble Code: P0690



Engine Controls Ignition Relay Feedback Circuit High Voltage

Possible Causes:



This test procedure assumes that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .
 
When disconnecting electrical connectors or removing fuses and relays from a fuse block, always inspect the component electrical terminals for corrosion and the mating electrical terminals for correct tension.
 

Trouble Code: P0691



Cooling Fan Speed Output Circuit Low Voltage

Trouble Code: P0692



Cooling Fan Speed Output Circuit High Voltage

Trouble Code: P0697



5-Volt Reference 3 Circuit

Possible Causes:



It may be possible to locate the fault by disconnecting one component at a time from the 5-volt reference circuit while viewing the 5-Volt Reference circuit parameter on the scan tool. The scan tool parameter would change from Fault to OK when the source of the fault is disconnected.
 
If all 5-volt reference components have been disconnected and a Fault is still indicated, the fault may exist in the wiring harness.
 

Trouble Code: P0698



5-Volt Reference 3 Low Voltage

Possible Causes:



It may be possible to locate the fault by disconnecting one component at a time from the 5-volt reference circuit while viewing the 5-Volt Reference circuit parameter on the scan tool. The scan tool parameter would change from Fault to OK when the source of the fault is disconnected.
 
If all 5-volt reference components have been disconnected and a Fault is still indicated, the fault may exist in the wiring harness.
 

Trouble Code: P0699



5-Volt Reference 3 High Voltage

Possible Causes:



It may be possible to locate the fault by disconnecting one component at a time from the 5-volt reference circuit while viewing the 5-Volt Reference circuit parameter on the scan tool. The scan tool parameter would change from Fault to OK when the source of the fault is disconnected.
 
If all 5-volt reference components have been disconnected and a Fault is still indicated, the fault may exist in the wiring harness.
 

Trouble Code: P06A6



Transmission Control Module (TCM) Requested MIL Illumination

Possible Causes:



MIL control circuit is shorted to ground
 
Check the TCM for any trouble codes in memory that are responsible for the request to turn on the MIL
 
TCM has failed
 

Trouble Code: P0700



Transmission Control Module (TCM) Requested MIL Illumination

Possible Causes:



DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.
 

Trouble Code: P0700



Clutch Switch Circuit Malfunction (M49/MM6)

Possible Causes:



Clutch switch circuit is open, shorted to ground or to power
 
Clutch switch power circuit is open (test the ENG IGN fuse)
 
Clutch switch is out of adjustment, damaged or has failed
 
ECM has failed
 

Trouble Code: P0703



Brake Switch Circuit 2

Possible Causes:



If a BCM has been replaced, the brake pedal position (BPP) sensor must be calibrated. Refer to Brake Pedal Position Sensor Calibration .
 
This DTC may be stored as a history DTC without affecting the operation of the ECM. If stored only as a history DTC, do not replace the BCM or ECM.
 

Trouble Code: P0711



Transmission Fluid Temperature (TFT) Sensor Performance

Possible Causes:



The DIC, if equipped, will display TRANSMISSION HOT - IDLE ENGINE when the transmission fluid temperature reaches 132°C (270°F). Ask the customer about possible overloading, exceeding the trailer towing limit, or towing in overdrive.
 

Trouble Code: P0712



Transmission Fluid Temperature (TFT) Sensor Circuit Low Voltage

Trouble Code: P0713



Transmission Fluid Temperature (TFT) Sensor Circuit High Voltage

Trouble Code: P0716



Input Speed Sensor Performance

Trouble Code: P0717



Input Speed Sensor Circuit Low Voltage

Trouble Code: P0719



TCC Brake Switch Circuit Low Input

Possible Causes:



TCC brake switch circuit is open or shorted to ground
 
TCC brake switch power circuit is open (test ABS or ERL fuse)
 
TCC brake switch is out of adjustment or damaged
 
ECM has failed
 

Trouble Code: P0722



Output Speed Sensor Circuit Low Voltage

Trouble Code: P0723



Output Speed Sensor Circuit Intermittent

Trouble Code: P0741



Torque Converter Clutch (TCC) System - Stuck Off

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0741



TCC System Mechanically Stuck Off

Possible Causes:



Converter clutch apply valve stuck in "off" (release) position
 
Misaligned or damaged valve body gasket
 
Restricted apply valve passage
 
TCC PWM valve exhaust orifice in damaged or it has failed
 
TCC solenoid valve mechanically stuck in "off" position
 

Trouble Code: P0742



Torque Converter Clutch (TCC) System - Stuck On

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0748



Pressure Control (PC) Solenoid Control Circuit

Trouble Code: P0751



1-2 Shift Solenoid (SS) Valve Performance - No First, Fourth or Fifth Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0752



1-2 Shift Solenoid (SS) Valve Performance - No Second or Third Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0756



2-3 Shift Solenoid (SS) Valve Performance - No First or Second Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0757



2-3 Shift Solenoid (SS) Valve Performance - No Third, Fourth or Fifth Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0761



4-5 Shift Solenoid (SS) Valve Performance - No Fourth Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0762



4-5 Shift Solenoid (SS) Valve Performance - No Fifth Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
Inspect transmission fluid lines to radiator. Lines may be pinched, plugged or twisted.
 
Refer to Shift Solenoid Valve State and Gear Ratio .
 

Trouble Code: P0806



Clutch Pedal Position (CPP) Sensor Circuit Performance

Trouble Code: P0807



Clutch Pedal Position (CPP) Sensor Circuit Low Voltage

Trouble Code: P0808



Clutch Pedal Position (CPP) Sensor Circuit High Voltage

Trouble Code: P080A



Clutch Pedal Position (CPP) Not Learned

Trouble Code: P0815



Upshift Switch Circuit

Trouble Code: P0816



Downshift Switch Circuit

 
label.common.footer.alt.autozoneLogo