Subaru Car 1998-05

Removal & Installation

Print

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box and lower metal bracket.
  4.  
  5. Disconnect the blower motor electrical harness.
  6.  
  7. Disconnect the flexible aspirator pipe from the blower motor base.
  8.  
  9. Remove the retainer screws, then lower the blower motor out.
  10.  
  11. Installation is the reverse of removal. Be sure to secure all components.
  12.  
  13. Test for proper blower motor operation.
  14.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box.
  4.  
  5. Disconnect the blower motor wiring harness.
  6.  
  7. Disconnect the aspirator pipe.
  8.  
  9. Remove the blower motor mounting screws.
  10.  
  11. Remove the blower motor assembly.
  12.  
  13. Installation is the reverse order of removal.
  14.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box.
  4.  
  5. Loosen the nut to remove the support beam stay.
  6.  
  7. Disconnect the blower motor wiring harness.
  8.  
  9. Disconnect the blower resistor connector.
  10.  
  11. Loosen the bolt and nut to remove the blower motor unit.
  12.  
  13. Installation is the reverse order of removal.
  14.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box and lower metal bracket.
  4.  
  5. Disconnect the blower motor electrical harness.
  6.  
  7. Disconnect the flexible aspirator pipe from the blower motor base.
  8.  
  9. Remove the retainer screws, then lower the blower motor out.
  10.  
  11. Installation is the reverse of removal. Be sure to secure all components.
  12.  
  13. Test for proper blower motor operation.
  14.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box and back pocket panel.
  4.  
  5. Disconnect the blower motor wiring harness.
  6.  
  7. Disconnect the aspirator pipe.
  8.  
  9. Remove the blower motor mounting screws.
  10.  
  11. Remove the blower motor assembly.
  12.  
  13. Installation is the reverse order of removal.
  14.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box stopper and then remove the glove box.
  4.  
  5. Disconnect the blower motor wiring harness.
  6.  
  7. Disconnect the aspirator pipe.
  8.  
  9. Remove the blower motor mounting screws.
  10.  
  11. Remove the blower motor assembly.
  12.  
  13. Installation is the reverse order of removal.
  14.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box lower cover.
  4.  
  5. Disconnect the blower motor wiring harness.
  6.  
  7. Remove the mounting screws and remove the blower motor.
  8.  
  9. Installation is the reverse order of removal.
  10.  

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the glove box.
  4.  
  5. Remove the wiring harness bracket mounting bolts.
  6.  
  7. Remove the nuts of the keyless unit stay and cruise unit stay.
  8.  
  9. Disconnect the sunroof electrical connector.
  10.  
  11. Disconnect the servo connector.
  12.  
  13. Disconnect the blower motor electrical harness.
  14.  
  15. Remove the blower motor mounting screws.
  16.  
  17. Disconnect the aspirator pipe.
  18.  
  19. Remove the blower motor unit.
  20.  
  21. Installation is the reverse order of removal.
  22.  



Click image to see an enlarged view

Fig. Climate control components-SVX


CAUTION
Some models may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in this section.

  1. Disconnect the negative battery cable. If equipped with a passenger side air bag, wait at least 10 minutes before doing any work on the vehicle to allow the air bag time to disarm.
  2.  
  3. Remove the glove box.
  4.  
  5. Remove the glove box lower support bracket.
  6.  
  7. Disconnect the blower motor electrical harness.
  8.  
  9. Remove the blower motor flexible vent tube.
  10.  
  11. Remove the blower motor mounting screws.
  12.  
  13. Remove the blower motor.
  14.  
  15. Installation is the reverse of removal. Tighten all components to specifications.
  16.  

 
label.common.footer.alt.autozoneLogo