Log In
Search suggestions

    My Vehicles

    2002 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl

    My Store

    1720 S RIDGEWOOD A
    (386) 427-1210

    CLOSED Open at 7:30 AM

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Suzuki Aerio, Verona 2002-06

    Removal & Installation

    Print


    NOTE
    Before servicing, or working around, the SRS system, turn the ignition switch OFF , disconnect the battery and wait at least three minutes.

    1. Before servicing the vehicle, refer to the Precautions Section.
    2.  

    The dashboard will need to be removed in order to remove the blower motor.

    1. Move the front seats back.
    2.  
    3. Remove or disconnect the following:

      The negative battery lead.
       
      The A-post panels of the dashboard
       
      The end covers on both sides

      Click image to see an enlarged view

      Fig. Location of A-post dash panels and end covers

       
      The soundproofing panels
       
      The courtesy lighting
       
      The On-Board Diagnostic (OBD) connector
       
      The steering wheel
       
      The combined instrument panel
       
      Gear selector assembly and steering wheel module
       
      The center console
       
      The dashboard environment panel
       
      The bracket for the road traffic information loudspeaker
       
      The connector for the hazard warning signal flasher
       
      Lift up and disconnect the sun sensor

      Click image to see an enlarged view

      Fig. Sun sensor removal

       

    4.  
    5. Remove or disconnect the following:

      Unhook the cable for the parking brake at the cable terminal by the release handle.
       
      Disconnect the cable for the gear selector lever lock.
       
      Detach the gear selector assembly (four screws). Turn the gear selector assembly a quarter turn with the control downwards towards the driver's seat.
       
      The glove compartment
       
      The connector for the passenger air bag module
       
      The lower mounting for the passenger air bag module. Remove the 2 screws
       
      The the 9 screws holding the dashboard
       
      Lift out dashboard.

      Click image to see an enlarged view

      Fig. Location of lower mounting for the passenger air bag module



      Click image to see an enlarged view

      Fig. Location of 5 of the 9 dashboard screws to be removed



      Click image to see an enlarged view

      Fig. Location of 4 of the 9 dashboard screws to be removed

       

    6.  
    7. Remove the fan motor from the climate control unit:
      NOTE
      Do not detach the air conditioning (A/C) pipes or the engine coolant hoses.

      1. Remove the drain hoses from the engine and filter housing.
      2.  
      3. Move the drain hoses out of the way.
      4.  
      5. Disconnect the electric connector at the fan motor.
      6.  
      7. Remove the 5 screws from the blower fan motor.
      8.  
      9. Detach and remove the blower fan motor and fan shroud.

        Click image to see an enlarged view

        Fig. Removing the fan motor from the climate control unit

      10.  

    8.  

    To install:

    1. Installation is the reverse of the removal procedure.
    2.  
    3. Install or connect the following:

      The blower fan motor and the cover on the climate control unit using the 5 screws
       
      The electrical connector for the blower motor
       
      The drain hose
       
      The climate control unit
       

    4.  
    5. Install or connect the following:
      NOTE
      Check that no wiring is trapped at the cable ducts.



      Lift the dashboard
       
      Pull the connector for the sun sensor out through the hole in the dashboard.
       



      The dashboard. Tighten the 9 M6 screws to 88 inch lbs. (10 Nm)
       
      The lower mounting for the passenger air bag module. Tighten the 2 M6 screws to 88 inch lbs. (10 Nm)
       
      The sun sensor
       
      The connector for the hazard warning signal flasher
       
      The cable for the parking brake. Hook the cable into place at the release handle
       
      The On-Board Diagnostic (OBD) connector
       
      The combined instrument panel
       
      The gear selector assembly and steering wheel module
       
      The steering wheel
       
      The bracket for the road traffic information loudspeaker
       
      The dashboard environment panel
       
      The gear selector assembly. Tighten the 4 M8 bolts to 18 ft. lbs. (24 Nm)
       
      The mechanical cable for the gear selector lever knob
       
      The center console
       
      The courtesy lighting
       
      The end covers of the dashboard on both sides
       
      The A-post panels
       

    6.  

    1. Disconnect negative (-) cable at battery.
    2.  
    3. Remove glove box.
    4.  
    5. Disconnect blower motor connector (1).
    6.  
    7. Remove blower motor (2).

      Click image to see an enlarged view

      Fig. Remove the blower motor

    8.  

    To install:

    Reverse removal procedure to install blower motor

     
    AutoZone Logo