Suzuki Vitara, Grand Vitara, XL7 2000-06

Timing Belt & Sprockets

Print

Removal & Installation



1.6L Engines

WARNING
Do not rotate the crankshaft counterclockwise or attempt to rotate the crankshaft by turning the camshaft sprocket.

  1. Remove the timing belt cover.
  2.  
  3. If the timing belt is not already marked with a directional arrow, use white paint, a grease pencil or correction fluid to do so.
  4.  
  5. Rotate the crankshaft clockwise until the timing mark on the camshaft sprocket and the -V- mark on the timing belt inside cover are aligned, and the punch mark on the crankshaft sprocket is aligned with the mark on the engine.
    WARNING
    Do not rotate the crankshaft or camshaft once the timing belt is removed, because the valves and pistons can come into contact, which may cause internal engine damage.

  6.  
  7. Disconnect one end of the tensioner spring. Loosen the timing belt tensioner bolt and stud, then, using your finger, press the tensioner plate up and remove the timing belt from the crankshaft and camshaft sprockets.
  8.  
  9. Remove the timing belt tensioner, tensioner plate and spring from the engine.
  10.  
  11. Install Suzuki tool 09917-68220, or equivalent, onto the camshaft sprocket to hold the camshaft from rotating. Loosen the camshaft sprocket retaining bolt, then pull the camshaft sprocket off of the end of the camshaft.
  12.  
  13. Remove the crankshaft timing belt sprocket by loosening the center bolt, while preventing the crankshaft from rotating. To hold the crankshaft from turning, use Suzuki tool 09927-56010, or equivalent, or a large prybar inserted in the transmission housing slot and the flywheel teeth. Pull the sprocket off of the end of the crankshaft. Be sure to retain the crankshaft sprocket key and belt guide for assembly.
  14.  
  15. If necessary, remove the timing belt inside cover from the cylinder head.
  16.  

To install:

Click image to see an enlarged view

Fig. Camshaft timing marks - Suzuki Vitara 1.6L 16-valve engine



Click image to see an enlarged view

Fig. Align the punch mark with the arrow for proper timing belt installation - Suzuki Vitara 1.6L 16-valve engine



Click image to see an enlarged view

Fig. Rotate the crankshaft clockwise until the camshaft and crankshaft timing marks are aligned - Suzuki Vitara 1.6L 16-valve engine

  1. If necessary, install the timing belt inside cover.
  2.  
  3. Slide the timing belt guide on the crankshaft so that the concave side faces the oil pump, then install the sprocket key in the groove in the crankshaft.
  4.  
  5. Slide the pulley onto the crankshaft, and install the center retaining bolt. Tighten the center bolt to 80 ft. lbs. (110 Nm). To hold the crankshaft from turning, use Suzuki tool 09927-56010, or equivalent, or a large prybar inserted in the transmission housing slot and the flywheel teeth.
  6.  
  7. Install the timing belt camshaft sprocket, ensuring that the slot in the sprocket engages the camshaft (pulley) pin; this ensures that the sprocket is properly positioned on the end of the camshaft. Secure the camshaft with the holding tool used during removal, then tighten the sprocket bolt to 44 ft. lbs. (60 Nm).
  8.  
  9. Assemble the timing belt tensioner plate and the tensioner, making sure that the lug of the tensioner plate engages the tensioner.
    WARNING
    If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  10.  
  11. Install the timing belt tensioner, tensioner plate and spring on the engine. Tighten the mounting bolt and stud only finger-tight at this time. Ensure that when the tensioner is moved in a counterclockwise direction, the tensioner moves in the same direction. If the tensioner does not move, remove it and the tensioner plate to reassemble them properly.
  12.  
  13. Loosen all rocker arm valve lash locknuts and adjusting screws. This will permit movement of the camshaft without any rocker arm associated drag, which is essential for proper timing belt tensioning. If the camshaft does not rotate freely (free of rocker arm drag), the belt will not be properly tensioned.
  14.  
  15. Rotate the camshaft sprocket clockwise until the timing mark on the sprocket and the -V- mark on the timing belt inside cover are aligned.
  16.  
  17. Using a wrench, or socket and breaker bar, on the crankshaft sprocket center bolt, turn the crankshaft clockwise until the punch mark on the sprocket is aligned with the arrow mark on the oil pump.
  18.  
  19. With the camshaft and crankshaft marks properly aligned, push the tensioner up with your finger and install the timing belt on the 2 sprockets, ensuring that the drive side of the belt is free of all slack. Release your finger from the tensioner. Be sure to install the timing belt so that the directional arrow is pointing in the appropriate direction.
    NOTE
    In this position, the No. 4 cylinder is at Top Dead Center (TDC) on the compression stroke.

  20.  
  21. Rotate the crankshaft clockwise 2 full revolutions, then tighten the tensioner stud to 97 inch lbs. (11 Nm). Then, tighten the tensioner bolt to 18 ft. lbs. (24 Nm).
  22.  
  23. Ensure that all 4 timing marks are still aligned as before; if they are not, remove the timing belt, and install and tension it again.
  24.  
  25. Install the timing belt cover and all related components.
  26.  

 
label.common.footer.alt.autozoneLogo