Tercel 1995-1996

Engine Mounts

Print

Removal & Installation



3E-E Engine
  1. Disconnect the negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding.
  2.  
  3. Raise and safely support the vehicle.
    CAUTION
    Make certain vehicle is properly supported when raising the engine.

  4.  
  5. Raise the engine slightly to take the tension off the motor engine mounts.
    NOTE
    When raising the engine to replace the engine mounts, DO NOT place the jack directly under the oil pan or the crankshaft torsional damper. Use a block of wood between the engine and the jack to prevent damage at the jacking point.

  6.  
  7. Loosen and remove the insulator mounting through-bolt and nut. Raise the engine sufficiently to remove the engine mount. Raising the engine assembly higher than necessary may cause damage.
  8.  
  9. Remove the engine mount mounting bolts and remove the mount.
  10.  

To install:

  1. Install the engine mount with the mounting bolts.
  2.  
  3. Slowly and safely lower the engine to install the engine mount through-bolt. Install the bolt and nut.
  4.  
  5. The engine mounts are to be tightened to the following torque specifications:
    1. LH mounting bracket to transaxle-36 ft. lbs. (49 Nm)
    2.  
    3. LH insulator to bracket-35 ft. lbs. (47 Nm)
    4.  
    5. RH mounting bracket to engine mounting bracket-47 ft. lbs. (64 Nm)
    6.  
    7. RH mounting bracket to insulator nut-47 ft. lbs. (64 Nm)
    8.  
    9. RH mounting insulator through-bolt-54 ft. lbs. (73 Nm)
    10.  
    11. Rear mounting insulator to body-58 ft. lbs. (79 Nm)
    12.  
    13. Rear mounting insulator through-bolt-47 ft. lbs. (64 Nm)
    14.  

  6.  
  7. Safely lower and remove the engine jack.
  8.  
  9. Lower the vehicle and reconnect the negative battery cable.
  10.  

5E-FE Engine
Left Mount

Specific to:

Toyota Tercel 1996

  1. Disconnect the negative battery cable.
  2.  
  3. Raise and safely support the vehicle.
    CAUTION
    Make certain vehicle is properly supported when raising the engine.

  4.  
  5. Raise the engine slightly to take the tension off the motor engine mounts.
    NOTE
    When raising the engine to replace the engine mounts, DO NOT place the jack directly under the oil pan or the crankshaft torsional damper. Use a block of wood between the engine and the jack to prevent damage at the jacking point.

  6.  
  7. Remove the bolt holding the engine ground to the left-hand bracket.
  8.  
  9. Remove the five bolts and disconnect the left-hand engine mounting bracket from the engine and transaxle.
  10.  

To install:

  1. Install the left-hand engine mounting bracket to the engine and transaxle and install the five bolts. Tighten the bolts to 47 ft. lbs. (64 Nm).
  2.  
  3. Connect the ground strap to the bracket and install the bolt. Tighten the bolt to 35 ft. lbs. (49 Nm).
  4.  
  5. Lower the engine and connect the negative battery cable.
  6.  

Rear Mount

Specific to:

Toyota Tercel 1996

  1. Disconnect the negative battery cable.
  2.  
  3. Raise and safely support the vehicle.
    CAUTION
    Make certain vehicle is properly supported when raising the engine.

  4.  
  5. Raise the engine slightly to take the tension off the motor engine mounts.
    NOTE
    When raising the engine to replace the engine mounts, DO NOT place the jack directly under the oil pan or the crankshaft torsional damper. Use a block of wood between the engine and the jack to prevent damage at the jacking point.

  6.  
  7. Remove the through-bolt nuts and the through-bolts.
  8.  
  9. Remove the engine mount bolts.
  10.  
  11. Raise the engine enough to remove the engine mounts.
    NOTE
    Only raise the engine enough to remove the mounts. Raising the engine too far could result in damage to some of the engine components.

  12.  

To install:

  1. Install the engine mounts and the engine bolts. Tighten the bolts to going through the support brackets to 58 ft. lbs. (78 Nm) and the other bracket bolts to 67 ft. lbs. (90 Nm).
  2.  
  3. Install the through-bolt and torque the bolt to 54 ft. lbs. (73 Nm).
  4.  
  5. Lower the vehicle and connect the negative battery cable.
  6.  

Right Mount

Specific to:

Toyota Tercel 1996

  1. Disconnect the negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding.
  2.  
  3. Raise and safely support the vehicle.
    CAUTION
    Make certain vehicle is properly supported when raising the engine.

  4.  
  5. Raise the engine slightly to take the tension off the motor engine mounts.
    NOTE
    When raising the engine to replace the engine mounts, DO NOT place the jack directly under the oil pan or the crankshaft torsional damper. Use a block of wood between the engine and the jack to prevent damage at the jacking point.

  6.  
  7. Remove the bolt and disconnect the ground strap from the engine mount.
  8.  
  9. Remove the engine mount through-bolt, nut and two bolts.
  10.  
  11. Remove the engine mount from the engine.
  12.  

To install:

  1. Install the engine mount to the bracket by installing the through-bolt. Do not torque the bolt at this time.
  2.  
  3. Install the engine mount to the engine and install the four nuts and two bolts.
  4.  
  5. Tighten the bolts as follows:

    Bolts and nut to 47 ft. lbs. (64 Nm)
     
    Through-bolt: 54 ft. lbs. (73 Nm)
     

  6.  
  7. Lower the engine and connect the negative battery cable.
  8.  

 
label.common.footer.alt.autozoneLogo