Tercel 1995-1996

Seats

Print

Removal & Installation



Rear Bench Seat Back

Specific to:

Toyota Tercel 1995-1996


NOTE
The seat bottom cushion need not be removed for this procedure, but access is improved with the cushion removed.

  1. Remove the lower bolts holding the seat back to the body.
  2.  
  3. Pull outward and push upward on the bottom edge of the seat back. This will release the seat back from the L-shaped hangers holding it.
  4.  
  5. Remove the seat back from the car.

    Click image to see an enlarged view

    Fig. Exploded view of the rear seats

  6.  

To install:

  1. Carefully fit the seat back onto the hangers.
  2.  
  3. Swing the back down and into place.
  4.  
  5. Install the lower retaining bolts and tighten them to 69 inch lbs. (7.8 Nm).
  6.  

Rear Bench Seat Cushion

Specific to:

Toyota Tercel 1995-1996

  1. Pull forward on the seat cushion releases. These are small levers on the lower front of the cushion.
  2.  
  3. Pull upward on the front of the seat cushion and rotate it free. It is not retained or bolted under the seat back.
  4.  

To install:

  1. Fit the rear of the cushion into place under the seat back.
  2.  
  3. Push inward and downward on the front of the cushion until the releases lock into place. Make sure the seat is locked into place and the releases are secure.

    Click image to see an enlarged view

    Fig. Exploded view of the rear seats

  4.  

Split/Folding Rear Seat Back

Specific to:

Toyota Tercel 1995-1996

  1. Push the seat back forward into a folded position.
  2.  
  3. Remove the carpeting from the rear of the seat back.
  4.  
  5. At the side hinge, remove the bolt holding the seat back to the hinge.
  6.  
  7. At the center hinge, remove the bolts holding the seat back to the hinge.
  8.  
  9. Remove the seat back from the car.

    Click image to see an enlarged view

    Fig. Exploded view of the rear seats

  10.  

To install:

  1. Install the seat back and Install the bolts finger tight.
  2.  
  3. Tighten the side hinge bolt to 13 ft. lbs. (18 Nm).
  4.  
  5. Tighten the center hinge bolts to 69 inch lbs. (7.8 Nm).
  6.  
  7. Install the carpeting and trim on the rear of the seat back.
  8.  

Split/Folding Rear Seat Cushion

Specific to:

Toyota Tercel 1995-1996

  1. At the front lower edge of the seat cushion, remove the bolts holding the seat cushion to the body. The bolts may be concealed under carpeting or trim pieces.
  2.  
  3. Pull upward on the front of the seat cushion and rotate it free. It is not usually retained or bolted under the seat back.

    Click image to see an enlarged view

    Fig. Exploded view of the rear seats

  4.  

To install:

  1. Fit the rear of the cushion into place under the seat back.
  2.  
  3. Push inward and downward on the front of the cushion until it is in place and the bolt holes align.
  4.  
  5. Install the retaining bolts and tighten them to 13 ft. lbs. (18 Nm).
  6.  

Front Seats

Specific to:

Toyota Tercel 1995-1996

The front seats are removed by disconnecting the mounting bolts holding the seat to the floor rails. The bolts may be under plastic covers which can be popped off with a small prybar. The seat assembly will come out of the car complete with the tracks and adjuster. When reinstalling the seat, make certain that the bolts are properly threaded and tightened to 27 ft. lbs. (37 Nm). SEAT MOUNTING AND RETENTION IS A CRITICAL SAFETY ITEM. NEVER ATTEMPT TO ALTER THE MOUNTS OR THE SEAT TRACKS.

Click image to see an enlarged view

Fig. Exploded view of the front seat assembly

 
label.common.footer.alt.autozoneLogo