Toyota Celica 1986-1993 Repair Guide

Headliner

Print

REMOVAL & INSTALLATION



1986-89 Vehicles
WITH SUNROOF
  1. Remove the sliding roof halfway.
  2.  
  3. Remove the clips on the front part of the headlining.
  4.  
  5. Slide the headlining forward and pull it off in an upward direction to remove.
  6.  

To install:

  1. Install headlining:
    1. Open the sliding roof halfway.
    2.  
    3. Insert the headlining from the front portion of the roof, and then insert the sun shade lock spring case into the show link.
    4.  
    5. Tap the headlining clips into the sliding roof panel.
    6.  

  2.  

CONVERTIBLE
  1. Remove rear drain trough trim cover, after removing the three screws.
  2.  
  3. Remove the screws attaching the headliner to the tacking strip.
  4.  
  5. Unhook the headliner straps from auxiliary "B" pillar brace.
  6.  
  7. Remove No. 4 bow garnish/retainer by unzipping and lowering backlight and then removing the screws and snap. Detach the headliner from the No. 4 bow. Pull to break the cement bond.
  8.  
  9. Remove headliner from No. 1 bow by unlatching the top and lowering it halfway. Remove the eight screws from No. 1 bow retainer.
  10.  
  11. Detach headliner from No. 2 and No. 3 bows and remove it.
  12.  

To install:

  1. Install the headliner to No. 2 and No. 3 bows.
  2.  
  3. Attach the headliner No. 3 and No. 2 retainers to the No. 3 and No. 2 bows.
  4.  
  5. Position No. 1 bow headliner retainer to No. 1 bow and install the eight screws.
  6.  
  7. Install headliner to No. 4 bow as follows:
    1. Raise the top and latch it to the windshield header.
    2.  
    3. Brush an even amount of adhesive along rear surface on No. 4 bow.
    4.  
    5. Attach headliner to No. 4 bow. Starting at center working toward each end, pull headliner rearward while attaching to pull out wrinkles.
    6.  

  8.  
  9. Install No. 4 bow garnish/retainer as follows:
    1. Unzip and lower backlight
    2.  
    3. Position the No. 4 bow garnish/retainer to No. 4 bow.
    4.  
    5. Install the six screws and snap.
    6.  
    7. Zip the backlight back up in position.
    8.  

  10.  
  11. Position headliner reinforcement tab to tacking strip and install the screw.
  12.  
  13. Hook headliner straps to auxiliary "B" pillar brace.
  14.  
  15. Install the rear drain trough trim cover by positioning the trim cover to the rear drain trough and installing the three screws.
  16.  



Click image to see an enlarged view

Fig. Fig. 1 Removing headliner1986-89 convertible vehicles shown

1990-93 Vehicles
WITH SUNROOF
  1. Remove the sliding roof halfway.
  2.  
  3. Remove the clips on the front part of the headlining.
  4.  
  5. Slide the headlining forward and pull it off in an upward direction to remove.
  6.  

To install:

  1. Install headlining:
    1. Open the sliding roof halfway.
    2.  
    3. Insert the headlining from the front portion of the roof, and then insert the sun shade lock spring case into the show link.
    4.  
    5. Tap the headlining clips into the sliding roof panel.
    6.  

  2.  

CONVERTIBLE
  1. Unhook headliner straps from the top stack main pivot bracket.
  2.  
  3. Remove the screws attaching headliner to the back belt front trim garnish.
  4.  



Click image to see an enlarged view

Fig. Fig. 2 Removing headliner1990-93 convertible vehicles shown

  1. Remove headliner from No. 4 bow.
    1. Unlatch the top and lower it slightly.
    2.  
    3. Remove the seven screws and remove the No. 4 bow headliner retainer.
    4.  
    5. Detach the headliner from the No. 4 bow. Pull to break cement bond.
    6.  

  2.  
  3. Remove headliner from No. 1 bow.
    1. Lower the top halfway.
    2.  
    3. Remove the two clip retainers attaching the headliner to the No. 1 bow.
    4.  
    5. Remove the six screws and remove the No. 1 bow headliner retainer.
    6.  
    7. Detach the headliner from the No. 1 bow. Pull to break cement bond.
    8.  

  4.  
  5. Detach the headliner No. 2 and No. 3 bow retainers from the No. 2 and No. 3 bows and remove the headliner.
  6.  

To install:

  1. Install headliner to No. 2 and No. 3 bows.
    1. Unlatch the top and lower it halfway.
    2.  
    3. Align the center mark on the retainer with the center screw hole on the bow and attach the bow No. 2 and No. 3 headliner retainers to the No. 2 and No. 3 bows.
    4.  

  2.  
  3. Install headliner to No. 1 bow.
    1. Brush an even amount of adhesive along the rear surface of the No. 1 bow.
    2.  
    3. Raise top and latch it to the windshield header.
    4.  
    5. Align the center notch in the headliner with the center hole on the No. 1 bow and attach the headliner to the No. 1 bow. Starting at the center working toward each end, pull headliner forward while attaching to pull out wrinkles.
    6.  
    7. Install the No. 1 bow headliner retainer to No. 1 bow
    8.  
    9. Install the six screws.
    10.  
    11. Install the two clip retainers to attach the headliner to the No. 1 bow.
    12.  

  4.  
  5. Install headliner to No. 4 bow.
    1. Brush an even amount of adhesive along the rear surface of the No. 4 bow.
    2.  
    3. Align center notch in headliner with the center hole in the No. 4 bow and attach the headliner to No. 4 bow. Starting at the center and working toward each end, pull headliner rearward while attaching to pull out wrinkles.
    4.  
    5. Unlatch the top and lower it slightly.
    6.  
    7. Install the No. 4 bow headliner retainer to the No. 4 bow.
    8.  
    9. Install the seven screws.
    10.  

  6.  
  7. Install headliner to the back belt front trim garnish. Position the headliner reinforcement strap to the back belt front trim garnish and install the screw.
  8.  
  9. Hook headliner straps to the top stack main pivot bracket.
  10.  

 
label.common.footer.alt.autozoneLogo